36011
36
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
34 FT-2800M OPERATING MANUAL
The FT-2800M’s scanning capability provides the operator with many convenient methods
of rapid frequency navigation.
BASIC SCANNER OPERATION
Before activating the scanner, make sure that the Squelch is set to silence the background
noise when no signal is present. Scanning is not possible while the Squelch is open (if noise
or signals are being heard).
Scanning may be started or stopped using the microphones
[
UP
]
or
[
DWN
]
button. The
following techniques are used for scanning:
r Pressing and holding in either the
[
UP
]
or
[
DWN
]
button for one second in the VFO
mode will cause upward or downward band scanning, respectively, to begin.
r Pressing and holding in either the
[
UP
]
or
[
DWN
]
button for one second in the Memory
mode will cause memory channel scanning toward a higher- or lower-numbered memory
channel, respectively.
r Scanning pauses when a signal opens the squelch, and the decimal point on the display
will blink. You can choose one of three scan-resume modes (described later).
r To halt the scan manually, the easiest way is to push the PTT switch on the microphone
momentarily (no transmission will occur while you are scanning). The scan may also be
halted manually by pressing the microphones
[
UP
]
or
[
DWN
]
button, or the
[
D/
MR
(
MW
)]
key.
SCAN-RESUME OPTIONS
Three scan-resume modes are available on the FT-2800M:
r In the “BUSY” mode, the scanner will remain halted for as long as there is carrier present
on the channel; after the carrier drops at the end of the other station’s transmission,
scanning will resume.
r In the “HOLD” mode, the scanner will halt on a signal it encounters. It will not restart
automatically; you must manually re-initiate scanning if you wish to resume.
r In the “5 SEC” mode, the scanner will halt for five seconds only, after which scanning
will resume (whether or not the other station is still transmitting).
The default scan-stop mode is “BUSY.” To change the scan-resume mode, use the following
procedure:
1. Press and hold in the
[
MHz
(
SET
)]
key for one second, then rotate the DIAL knob to
select “23 SCAN.”
2. Press the
[
MHz
(
SET
)]
key, then rotate the DIAL knob to select the desired scan-resume
mode (BUSY/HOLD/5 SEC).
3. Press and hold in the
[
MHz
(
SET
)]
key for one second to save the new setting and exit to
normal operation.
SCANNING
36

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-2800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-2800 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info