644355
9
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
Car AM/FM Radio with USB/SD Control
XM-2RSU418BT
2
Owner’ Manual
Contents
Warnings Before Installation...................................................3-5
Before You Install.......................................................................6
Installation .................................................................................7
Wiring Connections...........................................................8-9
Control of the Unit..................................................................10
Bluetooth Operation................................................................11
Basic Operation..................................................................12
Radio Operation....................................................................13
RDS Operation.......................................................................14
USB/SD Operation..................................................................15
Remote Control......................................................................16
Simple Troubleshooting Guide...............................................17
Specifications........................................................................18
Welcome!
Thank you for purchasing this high-technology car stereo with
USB, SD/MMC control. This unit can encode and record songs
and radio programmes to your USB Flash disk or SD/MMC
card. If there is any compatibility problems, we recommend you
to format your flashdisk/storage card in FAT32 mode before
using it. If the problem persisits, kindly consult your dealer for
assistance.
3
Owner’ Manual
Important Warnings to Take Note of BEFORE Com-
mencing Installation
Damage Caused By Incorrect Installation or Usage is
NOT Covered By Warranty. PLEASE Take The Time To
Read The Installation Notes Carefully.
To Validate The Warranty Please Ensure That The Unit
Is Installed By A Professional, VAT Registered Car Au-
dio Installation Company.
To avoid shorts in your vehicles electrical system, be sure
to disconnect the battery cable before beginning installa-
tion.
• This unit is intended for vehicles with a 12-volt battery and
negative grounding. Before installing the unit in a recreational
vehicle, truck, or bus, check that the battery voltage is 12 volts.
Remove the two transport screws from the top of the unit
before installation.
The black lead is ground. A good chassis ground requires a
tight connection to ground. The area should be free from rust,
paint or any form of dirt. Please ground this lead separately
from the ground of high-current products such as power amps.
If you ground the products together and the ground becomes
detached, there is a risk of damage to the products or fire.
• Be sure to connect the colour coded leads according to the dia-
gram. Incorrect connections may cause the unit to malfunction
or damage the vehicle’s electrical system. Cords for this product
and those for other products may be different colours even if they
have the same function. When connecting this product to an-
other product, refer to the supplied installation manuals of both
products and connect cords that have the same function.
• Be sure to connect the negative (-) speaker leads to the nega-
tive (-) speaker terminal. Never connect the negative (-) speaker
leads to chassis ground.
• The unit is only designed for use with 4 speakers. Do not com-
bine outputs for use with 2 speakers. Do not ground negative
speaker leads to the chassis ground.
• Speakers connected to this unit must be high-power units with
a minimum rating of 45W and impedance of 4 to 8 ohms. Con-
necting speakers with output and/or impedance values other
than those noted here will result in damage to the head unit
Warnings Before Installation
4
Owner’ Manual
and the speakers. Check the condition of your speakers care-
fully- connecting this unit to old or degraded speakers may re-
sult in a fault which will damage the audio IC and invalidate the
warranty.
• If this unit is installed in a vehicle that does not have an ACC
(accessory) position on the ignition switch, the red lead of the
unit should be connected to a terminal coupled with ignition
switch ON/Off operations. If this is not done, the vehicle battery
may be drained when you are away from the vehicle for several
hours.
• Secure the wiring with cable clamps or adhesive tape. To pro-
tect the wiring, wrap adhesive tape around them where they lie
against metal parts. To avoid short-circuiting, cover all discon-
nected lead with insulating tape. There is a possibility of short-
circuiting if the leads are not insulated.
• Route and secure all wiring so it cannot touch any moving
parts, such as the gear lever and handbrake. Do not route wir-
ing in places that get hot, such as near the heater outlet. If the
insulation of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle’s body.
• Don’t pass the yellow lead through a hole into the engine com-
partment to connect to the battery. This will damage the lead’s
insulation and cause a very dangerous short.
• Do not shorten any leads. If you do, the protection circuit may
fail to work when it should.
• Never feed power to other equipment by cutting the insulation
of the power supply lead of the unit and tapping into the lead.
The current capacity of the lead will be exceeded, causing over-
heating.
• Since a unique audio I/C circuit is employed, never wire so
the speaker leads are directly grounded or the left and right
– speaker leads are common.
• When this product’s source is switched ON, a control signal
is outputted through the orange lead. Connect to an external
power amp’s system remote control or the car’s Auto-antenna
relay control terminal (max. 300mA 12 V DC). If the car features
a glass antenna, connect to the antenna booster power supply
terminal.
• When an external power amp is being used with this system,
do not connect the orange lead to the amp’s power terminal.
Likewise, do not connect the orange lead to the power termi
nal
of the auto-antenna. Such connection could cause excessive
current
drain and a major malfunction. Refer to the relevant owner’s manual
Warnings Before Installation
5
Owner’ Manual
for details on connecting the power amp and other units, then make
the connections correctly.
Do not block any vents or heater panels. Blocking them will cause
heat to build up and may result in fire.
Make sure that the unit has a good chassis ground. A good ground
connection will eliminate most electrical noise. A good chassis
ground requires a tight connection to the vehicles metal chassis.
The area around the ground connection should be clean, bare metal
without rust, paint, plastic or dirt for a good electrical connection.
If noise is still experienced when the motor of the vehicle acceler-
ates, a choke should be placed in line with the power to the unit. The
installation company will know what is required.
When replacing the fuse(s) the replacement must be of the same
amperage as shown on the fuse holder. Never replace a fuse with
another of a different value. If the fuse blows again please contact
your installation company.
Do not block vents or heater panels. Blocking them will cause heat
to build up inside and may result in fire.
Double check that all wiring and connections are correct before re-
connecting the battery and turning on the unit.
After completing the installation and before operating the unit, recon-
nect the battery, Then press the (RES) button with a pointed object,
such as a ball-point pen to set the unit to its initial status. After push-
ing the button, wait a few seconds for the red light to flash.
Tools for Installation
• 2 removal wrenches are supplied for taking out the old unit and place
with this brand name car radio. The following tools and supplies may
also be needed for the installation:
Tools for Installation:
- Philips Screw-drivers
- Wire Stripper
- Wire Cutter
- Hammer
- Pencil
- Electrical Tape
- Electric Drill
Supplies for Installation:
- Machine Screws
- Crimp Connectors
- 14 Gauge Wire for Power
Connections
- 14-16 Gauge Speaker Wires
* The above are not supplied.
Warnings Before Installation
6
Owner’ Manual
Before You Install
2. Mark Polarity of the Speaker Wires
Automotive audio equipment installations can be troublesome at
times, even to the most experienced of installation technicians.
If you are not confident working with electrical wiring, removing
and reinstalling interior panels, carpeting, dashboards or other
components of your vehicle, please call your dealer in order to
have the unit professionally installed.
1. Remove the Old Unit from the Dashboard
DIN Front Mount
DO NOT DISCONNECT WIRES
AT THIS TIME!
IMPORTANT:
Remove the two transport screws from the top of
the unit before installing.
2. Insert the keys supplied with the
old unit into both sides of the unit
as shown in figure below until
they click. Pull to remove the old
unit from the dashboard.
1. Remove the outer trim frame.
1.
While the old unit is playing,
disconnect the wires from
one speaker
2. Take a length of masking
tape and fold it around the
wire so it forms a flag.
3. On the masking tape mark
the polarity of the speaker
wires (+ & - ), as well as left
or right, and front or rear.
4. Double check that you
marked the first speaker
correctly by checking that
the speaker wires are the
same at the head unit.
5. Repeat this procedure for
all of the speakers.
6. Mark the power, ground,
and any other wires also
.
Marking the polarity of the speaker wires will make it easier to
connect the existing speakers to your car radio.Consult wiring
diagram of existing head unit before disconnecting any wires.
If
you are not positive of the polarity of the existing wires from
the speakers to the head unit, install new wires.
7
Owner’ Manual
WARNING!
Disconnect negative battery terminal from battery
before starting installation. Consult the vehicle’s
owners manual for proper instructions.
NOTE: Mark the polarity of the existing speaker wires
before disconnecting battery.
NOTE: Remove the two transport screws from the top
of the unit before installing.
NOTE: Make sure there is enough space for the instal-
lation of this double-din unit.
SUPPLIED TOOLS
Installation
8
Owner’ Manual
Wiring Connections
Black Ground
Connect to vehicle body/chassis. Make sure that you have a good
chassis ground. This will eliminate most electrical noise from the
motor and alternator. A good chassis ground requires a tight con-
nection to ground. The area should be free from rust, paint or any
form of dirt.
Yellow Memory backup
Connect to electrical terminal always supplied with power regard-
less of ignition switch position.
Blue-White Remote
Connect to Auto-antenna or power amp control wire/remote con-
nection. Maximum current 300Ma 12 V DC.(Low Current)
Radio Antenna
Connector A
1. Rear right speaker(+)/Purple
2.
3. Front right speaker(+)/Grey
5. Front left speaker(+)/White
Rear right speaker(-)/Purple-Black
4. Front right speaker(-)/Grey-Black
6. Front left speaker(-)/White-Black
7. Rear left speaker(+)/Green
8. Rear left speaker(-)/Green-Black
Connector B
1. -
2. -
3. -
4. Battery 12V (+)/Yellow
5. Antenna power/Blue-White
6. -
7. ACC+/Red
8. Ground/Black
RCA OUT
Left=White
Right=Red
Make sure that you have a good chassis ground. Good
ground connections will eliminate most electrical noise prob-
lems. A good chassis ground requires a tight connection
to the vehicle’s metal chassis. The area around the ground
connection should be clean, bare metal without rust, paint,
plastic, dust, or dirt for a good electrical connection.
9
Owner’ Manual
Wiring Connections
Speaker Wiring Notes
Follow the above wiring diagram to install the head unit with
new or existing speakers.
• This unit is designed for use with four (4) speakers with imped-
ance between 4 Ohms to 8 Ohms.
An impedance load of less than 4 Ohms could damage the
unit
• Never bridge or combine the speaker wire outputs. When not
using four speakers, use electrical tape to tape the ends of the
unused speaker outputs to prevent a short circuit.
• Never ground the negative speaker terminals to chassis
ground.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Xomax XM-2RSU418BT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Xomax XM-2RSU418BT in de taal/talen: Engels als bijlage per email.

De handleiding is 0,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Xomax XM-2RSU418BT

Xomax XM-2RSU418BT Gebruiksaanwijzing - Deutsch - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info