575122
10
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
10
Oscillating Tool EN
OPERATION INSTRuCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The power tool is intended for sawing and
remodelling wooden materials, plastic,
plaster, non-ferrous metals and fasteners
(e.g. nails and clamps) as well as for working
on soft wall tiles and for dry grinding of small
surfaces. It is especially suitable for working
close to edges and for flush cutting.
1. MOUNTING ACCESSORIES
CAUTION: For all work or when
changing accessories, always wear
protective gloves. Avoid danger of injury
from the sharp edges of the accessories.
Accessories can become very hot while
working, presenting danger of burns! Make
sure the tool is unplugged prior to
changing accessories.
WARNING: To reduce the risk of
injury, do not let the sharp side of
the accessory face back toward the
user’s hand.
- Loosen the Flange
Use the Allen Key to rotate the Flange
clockwise. (See Fig. A)
- Insert Accessories
Insert the Accessory onto the Universal Fit
TM
Accessory Interface. (See Fig. B)
- Tighten the Flange
- Use the Allen Key to rotate the Flange
counterclockwise until accessory is tightened
securely. (See Fig. C)
NOTE: For prior model Worx Sonicrafter
hex-interface accessories and most other
non-WORX branded accessories, the Flange
must be completely removed to install
accessory (See Fig. D).
2. MOUNTING/CHANGING THE
SANDING SHEET (See Fig. E)
Align the sanding sheet and press it onto the
sanding pad by hand.
Firmly press the power tool with the sanding
sheet against a flat surface and briefly switch
the power tool on. This provides for good
adhesion and prevents premature wear.
If one point has become worn, pull off the
sanding sheet, turn it 120° and place it on
again.
NOTE: For other various brands’ sanding
pad, use small flange provided.
3.MOUNTING THE SUCTION DEVICE
(See Fig. F-J)
When vacuuming, mount the suction device
as shown in F-J.
NOTE: Using the sanding pad perforated. You
can only do the vacuuming after fitting the
dust collector.
4. OPERATING THE ON/OFF SWITCH
To start the machine, push the On/Off switch
forward so that the “I” is indicated on the
switch.
To switch off the machine, push the On/Off
switch toward the rear so that the “0” is
indicated on the switch.
5 USING THE VARIABLE SPEED DIAL
Select oscillation frequency (speed) while the
motor is running.
The Variable Speed Dial can be used to set
the optimum oscillating frequency according
to the accessories used and the respective
application.
High oscillation frequency:
Sanding, sawing, rasping and polishing stone
and metal.
Low oscillation frequency:
Scraping, polishing varnishes.
6. SANDING
Typical application: wood, metal; small areas,
especially corners, edges and places difficult
to access.
Select high oscillation frequency.
Sand with a constant movement and light
pressure.
Heavy pressure does not increase the
removal – the sanding sheet merely wears
faster.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worx WX676.7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worx WX676.7 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info