673279
9
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
Belt sander EN
98
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for dry sanding–with
high removal capacity–of wood, plastic, metal,
filler as well as varnished surfaces.
1. ON/OFF SWITCH
Depress to start and release to stop your tool.
2. SWITCH LOCK-ON BUTTON
(See Fig. A)
Depress on/off switch (2) then lock on button
(3). Your tool is now locked on for continuous
use. To switch off your tool just depress and
release the on/off switch.
3. VARIABLE SPEED CONTROL DIAL
Adjust the variable speed control (1) to
increase or decrease the speed according to
the material and sanding belt specification
to be used (also possible during no load
operation). See the table below for general
guidance on speed selection. Avoid prolonged
use at very low speed as this may damage
your sanders motor.
Material Speed selection Belt grit
Solid wood 5-6 80
Veneer 2-4 150
Chipboard 1-5 60/80
Plastics 2-5 100
Steel 5-6 80
Paint
removal
6 40/60
Balsa wood 1-3 100
Acrylic 1-2 100
4. CHANGING A SANDING BELT (See Fig. B, C)
WARNING!WARNING! Remove the
main plug from the socket before
changing sanding belt.
Pull the lever (7) to release the belt tension.
Remove and fit a new belt over both rollers.
Ensure the direction of rotation arrows on the
belt and the sander are the same. Close the
lever to tension the belt.
5. BELT CENTERING CONTROL (See Fig. D)
WARNING! Wear eye protection
before carrying out a belt centering
adjustment.
Turn the machine upside down, hold it firmly
with one hand, start the motor and release the
switch immediately after observing tracking
of sanding belt. If abrasive belt runs outward,
turn tracking adjustment knob counter-
clockwise and clockwise if belt runs inward.
Adjust the belt until the outer edge of the belt
is even with the outer edge of the base-plate
(12). Belt life will be greatly increased by
keeping the tracking adjustment set properly.
6. DUST BAG (See Fig. E)
Always operate your sander with the dust bag
fitted. For the best performance always empty
the dust bag in time. Remove the shaft from
the dust bag and shake out dust. To remove
the bag, slide the mounting bracket out and
away from the sander. To refit the bag, firmly
push the mounting bracket into the location
on the sander housing.
7. ASSEMBLE THE DUST EXTRACTION
ADAPTER (See Fig. F, G)
Your sander is equipped with two dust
extraction adapters, which are designed for
connecting the hose of a vacuum cleaner.
Insert the 35mm adapter (13a) into the outlet
until it is secured (See F), then insert the 32
mm adapter (13b) into the back of the 35 mm
adapter (Fig. G).
8. DRIVE BELT REPLACEMENT.
WARNING! Remove the main plug
from the socket before carrying out
a drive belt replacement.
Remove the three screws and the belt cover.
Carefully cut the drive belt if not already
broken and remove from your belt sander. Fit
your new drive belt around the large pulley.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worx WX661.1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worx WX661.1 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info