575073
13
Verklein
Vergroot
Pagina terug
1/172
Pagina verder
Mini multi-function saw EN
13
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE:
The machine is intended for lengthways
and crossways cutting of wood with straight
cutting lines, alumunium, PVC pipe and tile,
etc., while resting firmly on the work piece.
1. INSTALL/CHANGE THE BLADE
(See Fig. A)
WARNING: Be sure to wear
protective work gloves while
handling a saw blade. The blade can
injure unprotected hands.
WARNING: This tool will be
extremely hot after use. Be sure
to let saw, blade and blade spindle
clamping screw cool before changing
blades.
a. Unplug the saw.
WARNING: To prevent personal
injury, Always disconnect the plug
from power source before assembling
parts, making adjustments or changing
blades.
b. Loosen the blade spindle clamping screw
using the two hex keys included. Place
one key into the blade spindle clamping
screw and the other key into the back of the
spindle assembly. (See Fig. A)
c. Turn the key that is in the clamping screw
clockwise while holding the other key
stationary.
d. Remove the screw and the blade clamping
washer. (See Fig. B)
e. Set the depth of cut scale to the maximum
depth of 22mm. Release the blade release
lever and rasie the base with the finger
lift bracket to expose the blade below the
base.
f. Grasp the blade with your gloved hand
and remove the blade, or install the blade,
through the blade slot in the base.
g. Place the new saw blade through the blade
slot in the base and onto the spindle shaft.
NOTE: The teeth of the blade should
point upward at the front of the saw as
shown in (See Fig. B).
NOTE: The warning copy and the Blade
Rotation Arrow shown on the blade should
face outward towards the operator so it can
be viewed (See Fig. C).
h. Replace the blade clamping washer .
i. Replace the spindle screw and hand tighten
it in a counterclockwise direction.
j. Use the two hex keys to tighten the spindle
clamping screw thoroughly.
k. Place the two hex keys back in the case.
NOTE: Never use a blade that is too thick to
allow the blade clamping washer to engage
with the flat side of the spindle.
2. MAKING DEPTH OF CUT
ADJUSTMENTS (See Fig. D)
NOTE: Always use the correct blade depth
setting. The correct blade depth setting for all
cuts should not be more than 6 mm below the
material being cut. Allowing more depth will
increase the chance of kickback and cause the
cut to be rough. Your saw is equipped with
a depth of cut scale that provides increased
depth of cut accuracy. The depth of cut scale
is located on the top of the upper blade guard
(See Fig. D).
Our suggest cut depth:
Max. cut depth
Wood 0-22mm
Alu 0-3mm
PVC pipe 0-12mm
Tile 0-8mm
TO SET THE BLADE DEPTH (Fig. E1, E2)
Determine the desired depth of cut. Unlock
the depth of cut and length of cut Indicator
adjustment/Lock lever. Slide the depth of cut
indicator to the desired depth of cut. Lock
down the depth of cut adjustment / lock lever.
The length of cut indicator (See Fig.D) is ideal
for plunge or pocket cutting into the middle
(or interior) of the work piece when you need
to know where the cut will begin and where
it will end. This feature allows you to pinpoint
the location where the blade will plunge into
the work piece, based on the blade depth that
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worx WX424.2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worx WX424.2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info