575152
10
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
Rotary Hammer EN
1110
9. DRILLING FUNCTION (See Fig. G, H)
1)Press the lock button (A) and rotate the
selector switch to make sign “ point to
the triangle. (See Fig. G)
2)Turn the hammer or drilling action selector
switch pointing to the drilling action
position. (See Fig. H)
3)You are now set up for drilling function.
10. CHISEL FUNCTION (See I, J)
1)For chipping, grooving or demolition
operation, press the lock button (A) and then
rotate the selector switch make sign
pointing to the triangle. (See Fig. I)
2)Turn the hammer or drilling action selector
switch pointing to the hammer action
position. (See Fig. J)
3)You are now set up for chisel work using
Chisel action.
WARNING: You must make
sure that the selector switch
is positively locked in chisel mode
position. If not, it could cause a hazard.
11. DUST COVER (See Fig. K)
Use the dust cover to prevent dust from
falling over the tool and on your self when
performing overhead drilling operations.
Attach the dust cover to the bit as shown in
the K.
12. LUBRICATION MACHINE (See Fig. L)
The machine is grease-lubricated. A grease
refill is only required during hammer work
efficiency is low. Open the grease box lid
at the top of the hammer using the pin
spanner provided. Then refill approx 30g
grease provided with your tool. The grease
specification is general purpose lithium based.
Use only Worx genuine hammer grease
(optional accessory).
CAUTION: Keep the container of grease
away from children.
13. TO REPLACE THE BRUSHES
(See Fig. M, N)
Disconnect the plug from the power supply.
Unscrew the carbon brush cap with
screwdriver.
Remove the carbon brush. Check the length
of the brush and replace if under 6mm. When
brushes need replacement always renew both
brushes, even if one is still more than 6mm
long.
Completely screw down the carbon brush cap.
Check that the tool is working. Before use,
allow it run for a few minutes to enable the
brushes to settle.
WORKING HINTS FOR
YOUR TOOL
1. Reduce the pressure on the drill bit when it
is about to break through. This will prevent
the drill from jamming.
2. When drilling a large hole, first drill a pilot
hole using a smaller drill bit.
3. Always apply pressure to your drill bit in a
straight line, and if possible at right angles
to the workpiece.
4. Never change the operating mode whilst
the drill is running.
5. Do not apply excessive pressure to the tool
when chiseling. Expressive force does not
speed up the work.
MAINTENANCE
Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Occasionally you may see sparks through the
ventilation slots. This is normal and will not
damage your power tool.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order to
avoid a hazard.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Worx-WX333

Zoeken resetten

  • De boor zou li en re om moeten kunnen draaien. Ik vind nergens een knop om de draai richting te wijzigen. Hoe krijg ik dit voor elkaar ? Gesteld op 22-10-2021 om 17:38

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worx WX333 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worx WX333 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools als bijlage per email.

De handleiding is 2,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info