575001
11
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
11
Lithium-Ion Cordless Drill/Driver EN
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for driving in and
loosening screws as well as for drilling in
wood, metal and plastic.
ASSEMBLY AND OPERATION
Action Figure
BEFORE OPERATION
Removing the battery pack See Fig. A1
Charging the battery See Fig. A2
Installing the battery pack See Fig. A3
ASSEMBLY
CHUCK ADJUSTMENT
WARNING: Always lock off trigger
switch and disconnect tool from power
source when changing accessories. Always
ensure the bit is secure before starting the tool.
Damage to the Chuck or a loose bit may cause
possible personal injury.
--Removing the bits See Fig. B2
--Inserting the bits See Fig. B1
OPERATION
Forward/reverse rotation
control
WARNING: Never
change the direction
of rotation when the
chuck is rotating, wait
until it has stopped!
See Fig. C1,
C2, C3
TWO-SPEED GEAR
CONTROL
See Fig. D
TORQUE ADJUSTMENT
DRILLING,SCREWDRIVING,
HAMMER DRILLING
See Fig. E
Operating the on/off switch
WARNING: Do not
operate for long
periods at low speed
because excess heat will
be produced internally.
See Fig. F
LED Light Indicator
Before operation, the LED light will be
activated when the On/Off switch is slightly
depressed, and will automatically turn off 20
seconds after the On/Off switch is released.
The tool and battery are equipped with a
protection system. When the LED Light is
quickly flashing 3 seconds and turn off, the
system will automatically cut off power to
the tool to extend battery life. The tool will
automatically stop during operation if the tool
and/or battery are placed under one of the
following conditions:
Overloaded: The tool is operated in a
manner that causes it to draw an abnormally
high current. In this situation, release the
Trigger Switch on the tool and stop the
application that caused the tool to become
overloaded. Then pull the Trigger Switch again
to restart.
Overheated: Under the condition above, if
the tool does not start, the Tool and Battery are
overheated. In this situation, let the Tool and
Battery cool before pulling the Trigger Switch
again.
Low battery voltage: The remaining
Battery capacity is too low and the tool will not
operate. In this situation, remove and recharge
the Battery.
WARNING: To turn on the light, press
the On/Off switch and make sure the
Forward/Reverse Rotation Control is on
right/left position.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Worx-WX152.1

Zoeken resetten

  • Heb de worx wx152.1 in 2016 gekocht nu schakelaar stuk bij de Praxis geweest woord niet meer gerepareerd, schakelaar stuk moet ik de machine nu wegooien ? Gesteld op 5-5-2019 om 16:44

    Reageer op deze vraag Misbruik melden
    • Wat is hier u antwoord op ik ben net buiten de garantie en u zou 3 tot 5 jaar gerantie mee de dat ik geregistreerd stond dat ben ik toch door de rekening. Geantwoord op 15-5-2019 om 14:30

      Waardeer dit antwoord Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worx WX152.1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worx WX152.1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools als bijlage per email.

De handleiding is 4,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info