724619

Workzone CKT718A Handleiding

168
Verklein
Vergroot
Pagina terug
1/168
Pagina verder
Xfinity Li-ION 20V
Instruction Manual
7PC CORDLESS KIT
MODEL NUMBER
CKT718A
Version number: 004
1300 889 028
info.aldi@positecgroup.com
05/2019
2323CKT718A
2
The contents of all Instruction Manual
20V Battery And Battery Charger 01
20V Drill/Driver 02
20V Impact Driver 03
20V Circular Saw 04
20V Detail Sander 05
20V LED Torch 06
20V Bluetooth Speaker 07
20V USB Charger 08
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
JLH122200370S&
Z10&ABP1815MA
Version number: 004
Battery And Battery Charger
01
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
Welcome
Congratulations in choosing to buy a Workzone® Titanium Xnity Plus
20V Li-ion Battery and Battery Charger
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of our
philosophy of customer service and satisfaction, are backed by our
comprehensive 1 Year Warranty. We hope you will enjoy your purchase
for many years to come.
When you open your packaging, rst remove all items and check there
are no parts damaged or missing. If you nd anything wrong, do not
operate the product until the parts have been replaced or the fault has
been rectied. Failure to do so could result in serious personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
The product is guaranteed to be free from defects in workmanship and par rom the
date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T
conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
20V Battery And Battery Charger
ts for a period of 60 months f
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
Contents
Application 5
Package Content List 5
Parts description 6
Description of symbols 7
General safety warnings 8
Operation 11
Maintenance 13
Warranty 13
Environmental protection 15
Accessories and After Sales Parts 15
FAQ/Troubleshooting 15
Technical Specications 16
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
1. Application
Xnity Plus 20V Li-ion Battery and Battery Charger–
JLH122200370S&Z10&ABP1815MA
2. Package Content List
First time users or inexperienced operators pay particular attention to the
operation of the Xnity Plus 20V Li-ion Battery and Battery Charger , including
details of starting and stopping and correct use of the Xnity Plus 20V Li-ion
Battery and Battery Charger on pages 11-13, as well as the maintenance
instructions on pages 13.
NOTE: This product is for private domestic DIY use only. It is not suitable for
commercial or trade use.
This Xnity Plus 20V Li-ion Battery and Battery Charger is used for charging
and supplying power to the products enclosed in this 20V Cordless Kit.
The batteries and charger are to be used only for its prescribed purpose. Any
other use is deemed to be a case of misuse.
2 x 20V Li-Ion Batteries
1 x Battery Charger Adaptor
1 x Plug Pack Charger
1 x Instruction Manual
1 x Warranty Card & Certicate
• Remove all packing
materials
• Ensure all parts on the
contents list are present
• Check the appliance,
and all accessories for
transportation damages
WARNING! Please read and understand this instruction manual
before use and keep it for your future reference. Your power tool
should only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the supplied battery and
charger or any ALDI Xnity Plus 20V Li-ion Battery or Battery Charger.
Other type of battery packs may burst causing personal injury and
damage. The battery pack must be recharged only with the supplied
battery charger adaptor and plug pack charger or any ALDI Xnity
Plus 20V Battery or Battery Charger.
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
3. Parts description
1. Battery Charger Adaptor
2. Plug Park Charger
3. Charging indicator light
4. Battery pack
5. Battery pack release button
3
2
1
5
4
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
To reduce the risk of injury, user must read instruction manual
Warning
For indoor use only
Conforms to relevant standards for electrical safety and
electromagnetic compatibility
12 Month Warranty Period
Do not crush, disassemble, short terminals or dispose in re;
there is a risk of burns explosion or re.
Do not put in water.
Do not charge the battery pack if the ambient temperature is
less then 0°C or greater than 40°C.
Double Insulation. There are two independent barriers of insulation
to protect you from the possibility of electrical shock.
Polarity.
Waste electrical products should not be disposed of
with household waste.
12
Li-Ion
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
5. General safety warning
General Safety Warnings
WARNING Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
- This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
- Children should be supervised to ensure that they do not play
with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
Additional safety instructions for your Battery Charger
1. Before charging, read the instructions.
2. For charge Li-ion battery pack only.
3. Do not charge a leaking battery.
4. Do not use chargers for works other than those for which they
are designed.
5. Before charging, ensure your charger is matching the local AC
supply.
6. The charging device must be protected from moisture.
7. Do not use the charging device in the open.
8. Do not short out the contacts of battery or charger.
9. Respect the polarity “+/-“ when charging.
10. Do not open the unit and keep out of the reach of children.
11. Do not charge the batteries of other manufactures or ill-suited
models.
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
12. Ensure that the connection between the battery charger and
battery is correctly positioned and is not obstructed by foreign
bodies.
13. Ensure battery charger slots are free of foreign objects and
protected against dirt and humidity. Store in a dry and frost-free
place.
14. When charging batteries, ensure that the battery charger is in
a well-ventilated area and away from inflammable materials.
Batteries can get hot during charging. Do not overcharge
any batteries. Ensure that batteries and chargers are not left
unsupervised during charging.
15. Do not recharge non-rechargeable batteries, as they can
overheat and break.
16. Longer life and better performance can be obtained if
the battery pack is charged when the air temperature is
between 18°C and 24°C. Do not charge the battery pack in air
temperatures below 0°C, or above 40°C. This is important as it
can prevent serious damage to the battery pack.
17. Charge only battery pack/s of the same model provided by the
manufacturer and of models recommended by manufacturer.
Safety Warnings for battery pack
a) Do not dismantle, open or shred cells of the battery pack.
b) Do not short-circuit a battery pack. Do not store battery
packs haphazardly in a box or drawer where they
may short-circuit each other or be short-circuited by
conductive materials. When the battery pack is not in use,
keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
c) Do not expose battery pack to heat or fire. Avoid storage
in direct sunlight.
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
d) Do not subject battery pack to mechanical shock.
e) In the event of the battery leaking, do not allow the
liquid to come into contact with the skin or eyes. If
contact has been made, wash the affected area with
copious amounts of water and seek medical advice.
f) Seek medical advice immediately if a cell or battery pack
has been swallowed.
g) Keep battery pack/s clean and dry.
h) Wipe the battery pack terminals with a clean dry cloth if
they become dirty.
i) Battery pack/s need to be charged before use. Always
refer to the instructions and use the correct charging
procedure.
j) Do not maintain battery pack on charge when not in use.
k) After extended periods of storage, it may be necessary
to charge and discharge the battery pack several times to
obtain maximum performance.
l) Battery pack gives its best performance when it is
operated at normal room temperature (20 °C ± 5 °C).
m) When disposing of battery packs, keep battery packs of
different electrochemical systems separate from each
other.
n) Recharge only with the charger supplied or any ALDI
Xfinity Plus 20V Chargers. Do not use any charger
other than that specifically provided for use with the
equipment.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery
pack.
o) Do not use any battery packs which are not designed for
use with the equipment.
p) Keep battery packs out of the reach of children.
q) Retain the original product literature for future reference.
r) Remove the battery from the equipment when not in use.
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
s) Dispose of properly.
t) Do not mix cells of different manufacture, capacity, size
or type within a device.
u) Do not remove battery pack from its original packaging
until required for use.
v) Observe the plus (+) and minus (–) polarity markings
on the battery and ensure correct use.
6. Important information – Product care
This Battery uses Lithium Ion Battery Cells. Care must be taken to
ensure both the safety and life of the pack is maintained. Ensure you
have read all of the safety notes in the previous pages before using
the Battery, Charger Adaptor or Plug Pack Charger.
Treat the Battery, Charger Adaptor & Plug Pack Charger with care
and within the guidelines of this manual.
If the Battery, Charger Adaptor & Plug Pack Charger becomes
immersed in water or any fluids, or is subject to a severe drop or it
does not operate within the guidelines of this manual immediately
STOP using it and have it checked.
7. Operation
7.1 Charging the battery
WARNING: The charger and battery are specially designed to
work together so do not attempt to use any other devices. The
only other battery or chargers that these components are
compatible with is any ALDI Xfinity Plus 20V Li-ion Battery or Battery
Charger. Never insert or allow metallic objects into your charger or
battery connections because an electrical failure and hazard will occur.
NOTE:
a) Do not use any charger other than that specifically provided
for use with the equipment, or any ALDI Xfinity Plus 20V Li-ion
12
12
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
Battery and Battery Charger.
b) If the battery is very hot, remove the battery from the charger
adaptor and allow time for the battery to cool down before
recharging.
c) The battery in your new tool is not charged when it leaves the
manufacturer. Therefore it must be fully charged before using
for the first time.
d) Charge the battery to reach full or no less than half charge
before storage. If the tool will not be used for long periods of
time, charge the battery every 3-6 months.
7.2 How to charge your battery pack (see fig a)
Charging procedure
1. Connect the battery charger adaptor (1) into the plug pack
charger (2).
2. Connect the plug pack charger (2) in to the 240V mains power
outlet and turn on. A “green” light indicates power.
3. Slide the battery charger adaptor (1) onto the battery (4) by
aligning the guiding rails. A click indicates the battery is fitted.
4. The plug pack charger (2) light will change to “red”. The battery
is now in the charging process. When the light returns to
“green”, the battery (4) is fully charged.
NOTE: The power to the charger should be turned off when
unattended, with or without a battery inserted.
Ambient temperature ranges
The ambient temperature range for tool,
battery use and storage is 0
o
C-45
o
C.
The recommended ambient temperature
range for the charging system during
charging is 0
o
C-40
o
C.
13
13
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
WARNING: When battery charge runs out after continuous use
or exposure to direct sunlight or heat, allow time for the
battery to cool down before re-charging to achieve the full charge.
CHARGING INDICATOR
Light Status
Red on
Charging
Green on
Fully Charged
8. Maintenance
WARNING Remove the plug from the socket before
carrying out any adjustment, servicing or maintenance.
Your battery / charger adaptor & Plug Pack Charger require no
additional lubrication or maintenance. Never use water or chemical
cleaners to clean them. Wipe clean with a dry cloth. Always store in
a dry place.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
9. Warranty
Your new WORKZONE
®
TITANIUM Xfinity Plus 20V Li-ion Battery and
Battery Charger will more than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new Xfinity Plus 20V Li-ion Battery and Battery
Charger easy and safe to operate, and, with proper care, it will give
you many years of dependable service.
CAUTION. Carefully read through this entire instruction manual
14
14
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
before using your new WORKZONE
®
TITANIUM Xfinity Plus 20V
Li-ion Battery and Battery Charger. Take special care to heed the
Cautions and Warnings.
Your WORKZONE
®
TITANIUM Xfinity Plus 20V Li-ion Battery and
Battery Charger has many features that will make your job faster
and easier. Safety, performance, and dependability have been given
top priority in the development of this Xfinity Plus 20V Li-ion Battery
and Battery Charger , making it easy to maintain and operate.
Use only WORKZONE
®
TITANIUM replacement parts for your
product. Non-conforming parts or modifications made to parts will
void your warranty.
What your 1 year warranty means
Great care has gone into the manufacture of this product and it
should therefore provide you with years of good service when used
properly.
In the event of product failure within its intended use over the
course of as quickly as possible once it has been brought to our
attention. In the unlikely event of such an occurrence, or if you
require any information about the product please contact us via
our after sales support services, details of which can be found in this
manual and on the product itself. After Sales Support
TEL: 1300 889 028
Service Support
If you have any issues with the operation of your Battery or Charger,
please call us on 1300 889 028 for advice, or email us at
info.aldi@positecgroup.com
15
15
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
10.Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
11.Accessories and After Sales Parts
The following is available for purchase by visiting https://help.tools/
or calling our customer service hotline on: 1300 889 028
12. FAQ/Troubleshooting
Fault Cause Remedy
The Battery pack
gets warm when
charging.
It’s a result of the
stepping down of the
chemical reactions
inside the batteries
during the charging
process.
This is normal.
2. 2323-CH: 20V
Charger
1. 2323-BAT: 20V
Lithium Ion Battery
16
16
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
Undiagnosable Fault. The battery / charger
needs to be repaired
or replaced.
Contact Customer
Service.
For further inquiries or issues associated with your Battery or
Charger, call our Customer Service on 1300 889 028 or email us at
info.aldi@positecgroup.com
13. Technical Specifications
Charger
Plug Pack Charger Model JLH122200370S
Charger Adapter Model Z10
Charger input 100-240VAC~50-60Hz 15W
Charger output 22VDC 370mA
Charging time
Ready for use in 4-6 Hours
Protection class /II
Charger weight 0.49 kg
Other Compatible Charger Models All ALDI Xfinity Plus 20V
Lithium-Ion Chargers
Battery
Voltage
20V Max.
Battery capacity 1.5Ah, Li-Ion
Battery Model Number ABP1815MA
Battery weight 0.38 kg
Other Compatible Battery Models All ALDI Xfinity Plus 20V
Lithium-Ion Batteries
17
17
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
MODEL No.:
info.aldi@positecgroup.com
JLH122200370S&Z10&ABP1815MA • 2323 • 05/2019
This Xfinity Plus 20V Li-ion Battery and Battery Charger complies
with the following Standards:
1. Charger:
Safety: IEC60335-1
IEC60335-2-29
AS/NZS 60335.1
AS/NZS 60335.2.29
EMC: EN55014-1
EN55014-2
EN61000-3-2
EN61000-3-3
2. Battery:
IEC 62133-2: 2017
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
CDT218XA.9
Version number: 004
Cordless drill / driver
02
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Welcome
Congratulations in choosing to buy a Workzone® Titanium 20V Li-ion
Cordless Drill / Driver.
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of our
philosophy of customer service and satisfaction, are backed by our
comprehensive 5 Year Warranty. We hope you will enjoy your purchase
for many years to come.
When you open your packaging, rst remove all items and check there
are no parts damaged or missing. If you nd anything wrong, do not
operate the product until the parts have been replaced or the fault has
been rectied. Failure to do so could result in serious personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the
date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T
conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
20V Li-Ion Cordless Drill / Driver
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Contents
Application 5
Package Content List 5
Parts description 6
Description of symbols 7
General Safety Warnings 8
Important information – Product care 14
Assembly 15
Operation 16
Maintenance 23
Warranty 24
Environmental protection 25
FAQ/Troubleshooting 26
Technical Specications 28
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
1. Application
20V Li-ion Cordless Drill / Driver
2. Package Content List
First time users or inexperienced operators pay particular attention to the
operation of the 20V Li-ion Cordless Drill / Driver, including details of starting
and stopping and correct use of the 20V Li-ion Cordless Drill / Driver on pages
15-22, as well as the maintenance instructions on page 23.
Intended use of 20V Li-ion Cordless Drill / Driver
NOTE: This product is for private domestic DIY use only. It is not suitable for
commercial or trade use.
This 20V Li-ion Cordless Drill / Driver is used for driving in and loosening screws
as well as for drilling in wood, metal and plastic.
The tool is to be used only for its prescribed purpose. Any other use is deemed to
be a case of misuse.
1 x 20V Li-Ion Cordless Drill / Driver
1 x Belt clip
1 x Double ended bit
1 x Instruction manual
1 x Warranty Card & Certicate
• Remove all packing materials
• Ensure all parts on the contents
list are present
• Check the appliance, and all
accessories for transportation
damages
WARNING! Please read and understand this instruction manual
before use and keep it for your future reference. Your product
should only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the supplied 20V Li-Ion
battery or charger or any ALDI Xnity Plus range of 20V Li-Ion battery
packs. Other type of battery packs may burst causing personal injury
and damage. The battery pack must be charged using with ALDI
Xnity Plus 20V Li-Ion battery chargers.
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
3. Parts description
1. Keyless chuck
2. Torque setting / collar
3. Two-speed gear selector
4.
Forward/Reverse rotation control
5. Soft grip handle
6. Belt clip
7. Battery pack
8. Battery pack release button
9. LED light
10. Trigger switch
11. Double ended bit
9
10
7
6
5
11
8
4
1
2 3
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
To reduce the risk of injury, user must read instruction manual
Warning
Wear ear protection
Wear eye protection
Wear breathing protection
Conforms to relevant standards for electrical safety and
electromagnetic compatibility.
60 Months Warranty
60
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
5. General safety warning
General Power Tool Safety Warnings
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless) power
tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power
tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free
from oil and grease. Slippery handles and grasping surfaces
do not allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of injury
and fire.
c) When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk of
12
12
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
injury.
f) Do not expose a battery pack or tool to fire or excessive
temperature. Exposure to fire or temperature above 130 °C
may cause explosion.
g) Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs. Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
13
13
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
Drill safety warnings
1 ) Safety instructions for all operations
a) Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
or fasteners may contact hidden wiring or its own cord.
Cutting accessory or fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live” and could give the
operator an electric shock.
2) Safety instructions when using long drill bits
a) Never operate at higher speed than the maximum speed
rating of the drill bit. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the
workpiece, resulting in personal injury.
b) Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the
bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
c) Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing breakage
or loss of control, resulting in personal injury.
Screwdriver and impact wrench safety warning
1. Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool “live” and
could give the operator an electric shock
14
14
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
6. Important information – Product care
NOTE: For any issuses related directly to your purchased ALDI Xfinity
Battery / charger, contact the Customer Service of the manufacturer
as listed on the battery / charger packaging, manual or on the label
on the battery / charger.
This drill / driver uses Lithium Ion Battery Cells. Care must be taken
to ensure both the safety and life of the pack is maintained. Ensure
you have read all of the safety notes in the previous pages before
using the drill / driver.
Treat the battery pack with care and within the guidelines of this
manual.
If the battery pack does become immersed in water or any fluids,
or is subject to a severe drop or it does not operate within the
guidelines of this manual or the supplied manual, immediately stop
using the battery pack and have it checked.
Use only the batteries and charger included with this kit, or any
ALDI Xfinity Plus 20V Li-Ion range of batteries and chargers.
15
15
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
7. Assembly
7.1 Installing and Removing the Battery Pack(7)
a) To Remove the Battery Pack (7) (See Fig. A1)
Depress the battery pack release button (8) firmly first and then slide
the battery pack (7) out and away from the drill / driver.
b) To Install the Battery Pack (7) (See Fig. A2)
Slide the fully charged battery pack (7) onto the drill / driver with
sufficient force until it clicks into position.
A1 A2
1
2
16
16
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
8. Operation
8.1 Trigger Switch (10) (See Fig. B)
Press in the trigger switch (10) to start the drill / driver. Fully release
pressure from the trigger switch (10) to stop the drill / driver.
The trigger switch (10) is fitted with a brake function which stops your
chuck immediately when you quickly release the trigger switch (10).
It is also a variable speed switch that delivers higher speed and
torque with increased trigger pressure. Speed is controlled by the
amount of pressure on the trigger switch (10).
WARNING: Do not operate for long periods at low speed
as excess heat can be produced internally.
NOTE: The variable speed control fitted to this drill/driver is not
intended to be used for long periods of time during the operation
of the task being performed. Use the variable speed to start drill/
driving and screwing tasks, and then fully depress the trigger once
the task has started.
8.2 Switch Lock (See Fig. C)
The trigger switch (10) can also be locked into an OFF position with
the use of the forward/reverse rotational control (4). This helps to
reduce the possibility of accidental starting when not in use. To lock
the trigger switch (10), push the forward/reverse rotating control
(4) into the center position.In this position, the trigger switch (10)
cannot be activated.
B C
17
17
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
8.3 Forward / Reverse Rotational Selector (See Fig. D1, D2)
For drilling and screw driving use the forward rotation marked
“ ” (forward/reverse rotating control (4) is moved to the right
when looking at the drill from the front) (See D1). Only use reverse
rotation marked “ ” (forward/reverse rotating control (4) is
moved to the left when looking at the drill from the front) (See D2)
to remove screws or releasing a jammed drill bit.
WARNING: Never change the direction of rotation when
the chuck is rotating, wait until it has stopped!
8.4 Two-Speed Gear Selector (3) (See Fig. E)
The two-speed gearbox allows you to select a gear with the
optimum speed and torque to suit the application.
NOTE: When changing the two speed high / low gear selector (3),
ensure the drill/driver is not operating.
1. To select the LOW gear (low speed, high torque setting), push the
two-speed gear selector (3) backward,towards the back of the drill/
driver. The number “1” will be displayed.
2. To select the HIGH gear (high speed, low torque setting), push the
two-speed gear selector (3) towards the chuck.The number “2” will
be displayed.
Gear 1
Low speed range: for screwdriving or working with large drilling
diameter
D1 D2
18
18
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Gear 2
High speed range: for working with small drilling diameter
WARNING: To prevent gear damage, always allow the
chuck to come to a complete stop before changing the
direction of rotation or the two-speed gear selector.
8.5 Chuck Adjustment (See Fig. F)
1. Open the keyless chuck (1) by unscrewing it in an anti-clockwise
direction, holding the drill/driver as shown in Fig F. Do this sufficiently
enough to allow the drill/driver bit to enter the jaws of the chuck.
2. Ensure the drill/driver bit is fully inserted, so that the chuck jaws
grip the straight section of the bit.Rotate the keyless chuck (1) clock-
wise until the jaws tighten on the drill/driver bit.The collar of the
chuck needs to be tightened firmly to ensure the drill/driver bit is held
securely.
To remove the drill/driver bit, rotate sharply the chuck in an
anticlockwise direction, sufficiently enough to allow the drill/driver
bit to be removed.
E
F
OPEN
CLOSE
19
19
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
8.6 Torque Adjustment (See Fig. G)
(Screw driving force of your drill / driver)
The torque is adjusted by rotating the torque setting / collar (2).
The torque is greater when the torque setting / collar (2) is set on a
higher setting. The torque is less when the torque setting / collar (2)
is set on a lower setting.
Make the setting as follows:
1 - 4 for driving small screws
5 - 9 for driving screws into soft material
10 - 14 for driving screws into soft and hard material
15 - 19 for driving screws into hard wood
20 - 21 for driving larger screws
for heavy drilling
G
20
20
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
8.7 Automatic Spindle Lock (See Fig. H)
The automatic spindle lock allows you to use it as a regular
screwdriver. You can give an extra twist to firmly tighten a screw,
loosen a very tight screw or continue working when the battery
energy has expired. For manual screwdriver purposes, the chuck is
automatically locked when the tool is off.
8.8 Using The LED Light (9)
To turn on the LED light (9), press the trigger switch (10). When you
release the trigger switch (10), the LED light (9) will turn off.LED
lighting (9) increases visibility-great for dark or enclosed areas.
H
21
21
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
8.9 Belt Clip (6) (See Fig. I)
The side belt clip (6) is used to assist to clip the drill / driver to your
waist belt while working. To install, insert the assembly screw
through the belt clip screw hole into the retaining hole on the drill
/ driver, and using a philips head screwdriver (not supplied), tighten
the screw by turning in a clockwise direction.
NOTE: The belt clip (6) can be assembled onto either side of the drill.
IMPORTANT: When attaching or replacing the belt clip (6), use only
the assembly screw that is provided. Be sure to securely tighten screw.
8.10 Drilling
When drilling into a hard smooth surface, use a center punch to
mark the desired hole location. This will prevent the drill bit from
slipping off center as the hole is started.
Hold the drill / driver firmly and place the tip of the bit at the point
to be drilled.
Depress the trigger switch (10) to start the drill / driver.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side pressure
to elongate a hole.
When drilling in metal, only use HSS drill bits in good
condition. Always use a magnetic bit holder when using
short screwdriver bits (These bits not included).
I
22
22
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
8.11 Overload Protection
When overloaded, the motor comes to a stop. Relieve the load on
the machine immediately and allow cooling for approx. 30 seconds
at the highest no-load speed.
8.12 Temperature cut out
If the drill/driver is constantly overloaded, or the drill/driver is used
constantly at maximum rating in high ambient conditions, the battery
cells may overheat causing the battery pack to shut down.
When this occurs you will need to allow the battery cells to cool.
NOTE: The drill/driver will not restart until the battery pack has cooled.
To reduce the temperature of the cells remove the battery pack from
the drill/driver and place the battery pack in a free air environment, out
of direct sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in refrigerators or
freezers.When the battery pack has cooled down it can again be used
to operate the drill/driver, as long as the load or the conditions causing
the original excessive temperature has been corrected.
8.13 Low voltage cut out
The battery pack used on this tool is fitted with a low voltage cut out
feature within the circuitry.The low voltage cut out feature operates
when the voltage drops below a preset value. This feature automatically
stops the drill/driver from operating (similar to that of the overload
condition). When this condition occurs you will need to either insert
another battery into the drill/driver or recharge the existing battery.The
low voltage cut out feature has been added to maximise the life of the
battery cells in the battery. When this occurs, recharge the battery pack
by following the battery charging section in this manual.
NOTE: Attempting to restart the tool without either recharging the
battery or installing another battery (with charge) will lead to drill/
driver restarting and then stopping again, after only a few seconds of
operation.
23
23
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
9. Maintenance
WARNING: Remove the battery pack from the driver
before carrying out any adjustment, servicing or
maintenance.
Your drill / driver requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool.
Never use water or chemical cleaners to clean your power tool.
Wipe clean with a dry cloth.
Always store your power tool in a dry place.
Keep the motor ventilation slots clean.
Keep all working controls free of dust.
Occasionally you may see sparks through the ventilation slots. This is
normal and will not damage your power tool.
For battery tools
The ambient temperature range for tool and battery use and
storage is 0
o
C-45
o
C.
The recommended ambient temperature range for the charging
system during charging is 0
o
C-40
o
C.
24
24
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
10. Warranty
Your new WORKZONE
®
TITANIUM 20V Li-ion Cordless Drill / Driver
will more than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new 20V Li-ion Cordless Drill / Driver easy and
safe to operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual
before using your new WORKZONE
®
TITANIUM 20V Li-ion Cordless
Drill / Driver. Take special care to heed the Cautions and Warnings.
Your WORKZONE
®
TITANIUM 20V Li-ion Cordless Drill / Driver has
many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in the
development of this 20V Li-ion Cordless Drill / Driver, making it easy
to maintain and operate.
Use only WORKZONE
®
TITANIUM replacement parts for your
product. Non-conforming parts or modifications made to parts will
void your warranty.
25
25
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
What your 5 year warranty means
Great care has gone into the manufacture of this product and it
should therefore provide you with years of good service when used
properly. In the event of product failure within its intended use over
the course of the first 5 years after the date of purchase, we will
remedy the problem as quickly as possible once it has been brought
to our attention. In the unlikely event of such an occurrence, or if
you require any information about the product please contact us via
our after sales support services, details of which can be found in this
manual and on the product itself.
After Sales Support TEL: 1300 889 028
Service Support
If you have any issues with the operation of your product, please call
us on 1300 889 028 for advice, or email us at
info.aldi@positecgroup.com
11.Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
26
26
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
12.FAQ/Troubleshooting
1. REASONS FOR DIFFERENT BATTERY PACK WORKING TIMES
Charging time problems, as above, and having not used a battery pack
for a prolonged time will reduce the battery pack working time. This
can be corrected after several charge and discharge operations by
charging & working with your drill. Heavy working conditions such as
large screws into hard wood will use up the battery pack energy faster
than lighter working conditions. Do not re-charge your battery pack
below 0
o
C and above 40
o
C as this will affect performance.
2. WHY DOES THE DRILL NOT TURN ON WHEN I PRESS THE
TRIGGER SWITCH (10)?
The forward/reverse rotation control (4) may be positioned in the lock
function position. Unlock the forward/reverse rotation control (4) by
putting it into the required rotation position – forward or reverse.
Push the trigger switch (10) and the drill / driver will start to rotate.
3. HOW DO I SELECT DIFFERENT TORQUE POSITIONS?
Verify the torque position of the torque adjustment ring (2). You can
find the torque adjustment ring (2) between the chuck (1) and the
drill body. Rotate the torque adjustment ring (2) to align the numbers
(screw driving force) with the triangular indicator on the top of the
drill / driver. To adjust the torque setting, rotate the torque adjustment
ring (2). The higher the number, the higher the output torque.
4. HOW DO I ADJUST THE TORQUE?
To adjust the torque setting, rotate the torque adjustment ring (2).
Position 1 is the lowest torque (screw driving force) and position 21 is
the highest torque (screw driving force).
Controlling the torque allows for better control when using the
drill / driver on specific screwing tasks and assists in preventing over-
fastening and over-tightening.
27
27
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CDT218XA.9 • 2323 • 05/2019
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
For setting the torque position, first select a low setting on the torque
adjustment ring (2) and align the selected number with the triangular
indicator on the top of the drill / driver.
Slowly increase the torque setting to the desired level. It is suggested to
test the setting on scrap material first.
5. HOW DO I SELECT DRILL FUNCTION?
When using the drilling function the torque control has no effect to the
output of the drill. The drill function is used when using the drill to drill
holes in metal, non ferrous material, wood, plastic and similar materials.
Rotate the torque adjustment ring (2) so the symbol of the drill bit
aligns with the triangular indicator on the top of the drill / driver.
6. HOW DO I USE THE 2 GEARS ON THE DRILL?
To select LOW speed (mark is 1) (e.g. low speed, high torque setting),
push the gear selector forward, towards the chuck. The number “1” will
be displayed.
To select the HIGH speed (mark is 2) (e.g. high speed, low torque
setting), push the gear selector backwards. The number “2” will be
displayed.
NOTE: The gears cannot be changed if the on off switch (10) is
depressed.
7. WHAT IS THE FUNCTION OF THE FORWARD/REVERSE SWITCH?
Forward/Reverse rotation control (4) allows you to change the direction
of the motor while the trigger switch (10) is not depressed.
Drill / driving uses the forward mode. The reverse mode is intended for
the removal of screws and assisting to remove jammed drill/driver bits.
8. WHAT DO I DO IF I HAVE AN ISSUE WITH MY DRILL?
If you have any issues with your drill / driver, please contact our
Customer Service line on 1300 889 028.
28
28
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CDT218XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
13. Technical Specifications
Voltage 20V d.c.
No load speed 0-400/0-1500/min
Number of clutch positions 21+1
Max torque 28 N.m
Chuck capacity 10 mm
Max. drilling capacity
Steel 10 mm
Wood 25 mm
Machine weight 0.9 Kg
Product Dimensions (L x W x H): 190x75x225 mm
MD: EN62841-1
EN62841-2-1
AS/NZS62841-1
AS/NZS62841-2-1
EMC: EN55014-1
EN55014-2
This 20V Li-ion Cordless Drill / Driver complies with the
following Standards:
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
CID180XA.9
Version number: 004
Impact Driver
03
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Welcome
Congratulations in choosing to buy a Workzone® Titanium 20V Li-ion
Cordless Impact Driver.
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of our
philosophy of customer service and satisfaction, are backed by our
comprehensive 5 Year Warranty. We hope you will enjoy your purchase
for many years to come.
When you open your packaging, rst remove all items and check there
are no parts damaged or missing. If you nd anything wrong, do not
operate the product until the parts have been replaced or the fault has
been rectied. Failure to do so could result in serious personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the
date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T
conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
20V Li-Ion Cordless Impact driver
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Contents
Application 5
Package Content List 5
Parts description 6
Description of symbols 7
General Safety Warnings 8
Important information – Product care 13
Assembly 14
Operation 16
Maintenance 20
Warranty 21
Environmental protection 22
FAQ/Troubleshooting 23
Technical Specications 24
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
1. Application
20V Li-ion Cordless Impact driver
2. Package Content List
First time users or inexperienced operators pay particular attention to the
operation of the 20V Li-ion Cordless Impact Driver, including details of
starting and stopping and correct use of the 20V Li-ion Cordless Impact
Driver on pages 14-19, as well as the maintenance instructions on page 20.
Intended use of 20V Li-ion Cordless Impact Driver
NOTE: This product is for private domestic DIY use only. It is not suitable for
commercial or trade use.
This 20V Li-ion Cordless Impact Driver is used for fastening and loosening of bolts,
nuts and various threaded fasteners. This tool is not intended for use as a drill.
The tool is to be used only for its prescribed purpose. Any other use is deemed to
be a case of misuse.
1 x 20V Li-Ion Cordless Impact Driver
1 x Belt clip + assembly screw (not tted)
1 x 50mm drill bit
1 x Instruction manual
1 x Warranty Card & Certicate
• Remove all packing materials
• Ensure all parts on the
contents list are present
• Check the appliance, and all
accessories for transportation
damages
WARNING! Please read and understand this instruction manual
before use and keep it for your future reference. Your product
should only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the supplied 20V Li-
Ion battery and charger included in this kit or any 20V Li-Ion ALDI
Xnity Plus range of 20V Li-Ion battery packs. Other type of battery
packs may burst causing personal injury and damage. The battery
pack must be charged using with ALDI Xnity Plus 20V Li-Ion battery
chargers.
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
3. Parts description
1. Forward/Reverse Selector
2. Trigger Switch
3. Soft Grip Handle
4. Belt Clip
5. Battery Pack
6. Battery Pack Release Button
7. LED light
8. Hex Drive
3
2
7
6
5
8
4
1
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
To reduce the risk of injury, user must read instruction manual
Warning
Wear ear protection
Wear eye protection
Wear breathing protection
Conforms to relevant standards for electrical safety and
electromagnetic compatibility.
60 Months Warranty
60
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
5. General safety warning
General Power Tool Safety Warnings
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless) power
tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power
tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free
from oil and grease. Slippery handles and grasping surfaces
do not allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of injury
and fire.
c) When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk of
12
12
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
injury.
f) Do not expose a battery pack or tool to fire or excessive
temperature. Exposure to fire or temperature above 130 °C
may cause explosion.
g) Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs. Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
General Power Tool Safety Warnings
1. Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live” and could give the
operator an electric shock.
13
13
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
6. Important information – Product care
NOTE: For any issuses related directly to your purchased ALDI Xfinity
battery / charger, contact the customer service of the manufacturer
as listed on the battery / charger packaging, manual or on the label
on the battery / charger.
This Impact Driver uses Lithium Ion battery cells. Care must be taken to
ensure both the safety and life of the pack is maintained. Ensure you
have read all of the safety notes in the previous pages before using the
Impact Driver.
Treat the battery pack with care and within the guidelines of this
manual.
If the battery pack does become immersed in water or any fluids, or is
subject to a severe drop or it does not operate within the guidelines of
this manual or the supplied manual, immediately stop using the battery
pack and have it checked.
Use only the batteries and charger included with this kit, or any ALDI
Xfinity Plus 20V Li-Ion range of batteries and chargers.
14
14
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
7. Assembly
7.1 Inserting A Bit Holder, Socket Or Screwdriver Bit
(See Fig. A)
Pull the hex drive (8) sleeve (a) forward. Fully insert the desired bit
into the hex drive (8) and release the sleeve (a).
NOTE: To ensure the bit is secure, try pulling the bit after releasing
the sleeve (a) to make sure the bit is fully locked in the hex drive (8).
7.2 Removing A Bit Holder, Socket Or Screwdriver Bit
(See Fig. B)
Pull the hex drive (8) sleeve (a) forward. Remove the bit out of the
hex drive (8) and release the sleeve (a).
A B
a a
15
15
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
7.3 Installing and Removing the Battery Pack
a) To Remove the Battery Pack (5) (See Fig. C1)
Depress the battery pack release button (6) firmly, then slide the
battery pack (5) out away from the tool.
b) To Install The Battery Pack (5) (See Fig. C2)
Slide the fully charged battery pack (5) onto the tool with sufficient
force until it clicks into position.
C1 C2
1
2
16
16
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
D
8. Operation
8.1 Trigger Switch (2) (See Fig. D)
Press in the trigger switch (2) to start the Impact Driver, and fully
release pressure off the trigger switch (2) to stop the Impact Driver.
The trigger switch (2) is fitted with a brake function which stops the
chuck / hex drive immediately when you quickly release the trigger
switch (2).
The trigger switch (2) also operates the variable speed by applying
various pressure to the trigger. Higher speed and torque results with
increased trigger pressure. Speed is controlled by the amount of
pressure applied to the trigger switch (2).
WARNING: Do not operate for long periods at low speed
as excess heat can be produced internally in the motor.
8.2 Forward / Reverse Selector (See Fig. E1, E2)
For fastening bolts or nuts, press the forward / reverse selector (1) as
marked “ ” (forward/reverse selector (1) is moved to the right as
shown in Fig. E1). For reverse rotation marked “ ” the forward/
reverse selector (1) is moved to the left as shown in Fig. E2, to loosen
or remove bolts or nuts fullstop.
WARNING: Never change the direction of rotation when
the chuck is rotating, wait until it has stopped!
17
17
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
8.3 Trigger Switch (2) Lock (See Fig. F)
The trigger switch (2) can be locked into the OFF position. This helps
to reduce the possibility of accidental starting when not in use. To
lock the trigger switch (2), push the forward/reverse selector (1) into
the centre position.
8.4 Using The LED Light (7)
To turn on the LED light (7), press the trigger switch (2). When you
release the trigger switch (2), the LED light (7) will turn off.LED
lighting (7) increases visibility - great for dark or enclosed areas.
E1
F
E2
18
18
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
G
8.5 Belt Clip (4) (See Fig. G)
The side belt clip (4) is used to assist to clip the Impact Driver to
your waist belt while working. To install, insert the assembly screw
through the belt clip screw hole into the retaining hole on the
Impact Driver, and using a philips head screwdriver (not supplied),
tighten the screw by turning in a clockwise direction
NOTE: The belt clip (4) can be assembled onto either side of the
Impact Driver.
IMPORTANT: When attaching or replacing the belt clip (4), use only
the assembly screw that is provided. Be sure to securely tighten
screw.
8.6 Overload Protection
When in overload condition, the motor will come to a stop. Reduce
the load on the machine immediately and allow to cool for approx.
30 seconds at the highest no-load speed.
8.7 Temperature Cut Out
If the Impact Driver is constantly overloaded, or the Impact Driver is
used constantly at maximum rating in high ambient conditions, the
battery cells may overheat causing the battery pack to shut down.
When this occurs you will need to allow the battery cells to cool.
NOTE: The Impact Driver will not restart until the battery pack has
cooled.
To reduce the temperature of the cells remove the battery pack
from the Impact Driver and place the battery pack in a free air
19
19
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
environment, out of direct sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in refrigerators
or freezers.
When the battery pack has cooled down it can again be used to
operate the Impact Driver, as long as the load or the conditions
causing the original excessive temperature has been corrected.
8.8 Low Voltage Cut Out
The battery pack used on this tool is fitted with a low voltage cut
out feature within the circuitry.
The low voltage cut out feature operates when the voltage drops
below a preset value. This feature automatically stops the Impact
Driver from operating (similar to that of the overload condition).
When this condition occurs you will need to either insert another
battery into the Impact Driver or recharge the existing battery.
The low voltage cut out feature has been added to maximise the
life of the battery cells in the battery. When this occurs, recharge
the battery pack by following the battery charging section in this
manual.
NOTE: Attempting to restart the tool without either recharging
the battery or installing another battery (with charge) will lead to
Impact Driver restarting and then stopping again, after only a few
seconds of operation.
20
20
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
9. Maintenance
WARNING: Remove the battery pack from the driver
before carrying out any adjustment, servicing or
maintenance.
Your power tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool.
Never use water or chemical cleaners to clean your power tool.
Wipe clean with a dry cloth.
Always store your power tool in a dry place.
Keep the motor ventilation slots clean.
Keep all working controls free of dust.
Occasionally you may see sparks through the ventilation slots. This is
normal and will not damage your power tool.
For battery tools
The ambient temperature range for tool and battery use and
storage is 0
o
C-45
o
C.
The recommended ambient temperature range for the charging
system during charging is 0
o
C-40
o
C.
21
21
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
10. Warranty
Your new WORKZONE
®
TITANIUM 20V Li-ion Cordless Impact Driver
will more than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new 20V Li-ion Cordless Impact Driver easy and
safe to operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual
before using your new WORKZONE
®
TITANIUM 20V Li-ion Cordless
Impact Driver. Take special care to heed the Cautions and Warnings.
Your WORKZONE
®
TITANIUM 20V Li-ion Cordless Impact Driver has
many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in the
development of this 20V Li-ion Cordless Impact Driver, making it easy
to maintain and operate.
Use only WORKZONE
®
TITANIUM replacement parts for your
product. Non-conforming parts or modifications made to parts will
void your warranty.
22
22
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
What your 5 year warranty means
Great care has gone into the manufacture of this product and it
should therefore provide you with years of good service when used
properly. In the event of product failure within its intended use over
the course of the first 5 years after the date of purchase, we will
remedy the problem as quickly as possible once it has been brought
to our attention. In the unlikely event of such an occurrence, or if
you require any information about the product please contact us via
our after sales support services, details of which can be found in this
manual and on the product itself.
After Sales Support TEL: 1300 889 028
Service Support
If you have any issues with the operation of your product, please call
us on 1300 889 028 for advice, or email us at
info.aldi@positecgroup.com
11.Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
23
23
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CID180XA.9 • 2323 • 05/2019
MODEL No.:
CID180XA.9 • 2323 • 05/2019
12.FAQ/Troubleshooting
1. REASONS FOR DIFFERENT BATTERY PACK WORKING TIMES
Charging time problems, as above, and having not used a battery
pack for a prolonged time will reduce the battery pack working time.
This can be corrected after several charge and discharge operations
by charging & working with your driver. Heavy working conditions
such as large screws into hard wood will use up the battery pack
energy faster than lighter working conditions. Do not re-charge
your battery pack below 0
o
C and above 40
o
C as this will affect
performance.
2. WHY DOES THE DRIVER NOT TURN ON WHEN I PRESS THE
TRIGGER SWITCH (2)?
The forward/reverse selector (1) is positioned in the lock function.
Unlock the forward/reverse selector (1) by putting it into the required
rotation position. Push the trigger switch (2) and the driver will start
to rotate.
3. WHAT IS THE FUNCTION OF THE FORWARD/REVERSE
SELECTOR (1)?
Forward/reverse selector (1) allows you to change the direction of the
motor while the trigger switch (2) is not depressed.
Driving uses the forward mode. The reverse mode is intended for the
removal of bolts, nuts and various threaded fasteners.
4. WHAT DO I DO IF I HAVE AN ISSUE WITH MY DRIVER?
If you have any issues with your driver, please contact our Customer
Service line on 1300 889 028.
24
24
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CID180XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
13. Technical Specifications
Rated voltage 20V d.c.
Rated no-load speed 0-2600/min
Impact rate 3400 bpm
Max torque 110 N.m
Chuck size 1/4” hex
Machine weight 0.91 kg
Product Dimensions (L x W x H): 155x80x225 mm
Safety: EN62841-1
EN62841-2-2
AS/NZS62841.1
AS/NZS62841.2.2
EMC: EN55014-1
EN55014-2
This 20V Li-ion Cordless Impact Driver complies with the
following Standards:
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
CSC165XA.9
Version number: 004
165mm Circular Saw
04
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Welcome
Congratulations in choosing to buy a Workzone® Titanium Xnity Plus
20V Li-Ion 165mm Circular Saw.
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of our
philosophy of customer service and satisfaction, are backed by our
comprehensive 5 Year Warranty. We hope you will enjoy your purchase
for many years to come.
When you open your packaging, rst remove all items and check there
are no parts damaged or missing. If you nd anything wrong, do not
operate the product until the parts have been replaced or the fault has
been rectied. Failure to do so could result in serious personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the
date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T
conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
20V Li-Ion 165mm Cordless Circular Saw
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Contents
Application 5
Package Content List 5
Parts description 6
Description of symbols 8
Product Safety 9
Safety instructions for all saws 13
Important information – Product care 16
Assembly 17
Operation 18
Maintenance 23
Warranty 23
Environmental protection 24
FAQ/Troubleshooting 25
Technical Specications 28
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
1. Application
20V Li-Ion 165mm Cordless Circular Saw
2. Package Content List
First time users or inexperienced operators pay particular attention to
the operation of the 20V Li-Ion 165mm Circular Saw, including details of
starting and stopping and correct use of the 20V Li-Ion 165mm Circular Saw
on pages 18-22, as well as the maintenance instructions on page 23.
Intended use of 20V Li-Ion 165mm Circular Saw
NOTE: This product is for private domestic DIY use only. It is not suitable for
commercial or trade use.
The 20V Li-Ion 165mm Circular Saw is intended for light use around the
home and domestic applications. It is particularly useful for trimming
plywood and similar sheet material. It is NOT suitable for metal cutting
blades or discs.
1 x 20V Li-Ion 165mm Circular Saw
1 x 5mm Hex key
1 x Saw blade
1 x Parallel guide
1 x Dust Extraction adapter
1 x Instruction manual
1 x Warranty Card & Certicate
• Remove all packing materials
• Ensure all parts on the contents
list are present
• Check the appliance, and all
accessories for transportation
damages
WARNING! Please read and understand this instruction manual
before use and keep it for your future reference. Your product
should only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the ALDI Xnity Plus
range of 20V Li-Ion battery packs. Other type of battery packs may
burst causing personal injury and damage. The battery pack must be
charged using with ALDI Xnity Plus 20V Li-Ion battery chargers.
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
3. Parts description
1. Lock-O Button
2. Trigger Switch
3. Front Handle
4. Spindle Lock Button
5. Base Plate Angle Scale
6. Base Plate Bevel Lock Knob
7. Parallel Guide Lock Knob
8. Cutting Mark - 45°
9. Cutting Mark - 0°
10. Parallel Guide
11. Base Plate
12. Lower Guard Lever
13. Lower Blade Guard
14. Fixed Guard
15. Dust Extraction Adapter
16. Battery Pack
17. Battery Pack Release Button
18. Inner Flange (See Fig. B3)
19. Saw Blade
20. Outer Flange (See Fig. B3)
21. Blade Bolt (See Fig. B3)
22. Cutting Depth Scale (See Fig. C)
23. Cutting Depth Lock Knob (See Fig. C)
24. Hex key (See Fig. K)
25. Blade rotation indicator
26. Main handle
27. Spindle
28. Parallel guide notches
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
13
1 263 2
272528
9
8 10
17
6
7
5
4
16
15
12
19
11
14
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
To reduce the risk of injury, user must read instruction
manual
Warning
Wear ear protection
Wear eye protection
Wear breathing protection
Conforms to relevant standards for electrical safety and
electromagnetic compatibility.
60 Months Warranty
Wear protective gloves when handling the saw blade.
The blade has sharp edges.
60
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
5. Product Safety
General safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
Keep your hair and clothing away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power
tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained
power tools.
12
12
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free
from oil and grease. Slippery handles and grasping surfaces
do not allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of injury
and fire.
c) When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk of
injury.
13
13
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
f) Do not expose a battery pack or tool to fire or excessive
temperature. Exposure to fire or temperature above 130 °C
may cause explosion.
g) Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs. Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
Safety instructions for all saws
a) DANGER: Keep hands away from cutting area and the
blade. Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they cannot
be cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot
protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth should be
visible below the workpiece.
d) Never hold workpiece in your hands or across your leg
while cutting. Secure the workpiece to a stable platform. It
is important to support the work properly to minimise body
exposure, blade binding, or loss of control.
e) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting tool
14
14
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
may contact hidden wiring or its own cord. Contact with a
“live” wire will also make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
f) When ripping always use a rip fence or straight edge guide.
This improves the accuracy of cut and reduces the chance of blade
binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the
mounting hardware of the saw will run off-centre, causing loss of
control.
h) Never use damaged or incorrect blade washers or bolt. The
blade washers and bolt were specially designed for your saw, for
optimum performance and safety of operation.
Further safety instructions for all saws
Kickback causes and related warnings
— kickback is a sudden reaction to a pinched, bound or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator;
— when the blade is pinched or bound tightly by the kerf closing
down, the blade stalls and the motor reaction drives the unit
rapidly back toward the operator;
— if the blade becomes twisted or misaligned in the cut, the teeth
at the back edge of the blade can dig into the top surface of the
wood causing the blade to climb out of the kerf and jump back
toward the operator.
Kickback is the result of saw misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
a) Maintain a firm grip with both hands on the saw and
position your arms to resist kickback forces. Position your
body to either side of the blade, but not in line with the
blade. Kickback could cause the saw to jump backwards, but
15
15
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
kickback forces can be controlled by the operator, if proper
precautions are taken.
b) When blade is binding, or when interrupting a cut for any
reason, release the trigger and hold the saw motionless
in the material until the blade comes to a complete stop.
Never attempt to remove the saw from the work or
pull the saw backward while the blade is in motion or
kickback may occur. Investigate and take corrective actions to
eliminate the cause of blade binding.
c) When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are not
engaged into the material. If saw blade is binding, it may
walk up or kickback from the workpiece as the saw is restarted.
d) Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag under their
own weight. Supports must be placed under the panel on both
sides, near the line of cut and near the edge of the panel.
e) Do not use dull or damaged blades. Unsharpened or
improperly set blades produce narrow kerf causing excessive
friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking levers must be
tight and secure before making cut. If blade adjustment
shifts while cutting, it may cause binding and kickback.
g) Use extra caution when sawing into existing walls or
other blind areas. The protruding blade may cut objects that
can cause kickback.
Safety instructions for circular saw with inner pendulum guard
Lower guard function
a) Check lower guard for proper closing before each use. Do
not operate the saw if lower guard does not move freely
and close instantly. Never clamp or tie the lower guard
into the open position. If saw is accidentally dropped, lower
guard may be bent. Raise the lower guard with the retracting
16
16
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
handle and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the
guard and the spring are not operating properly, they
must be serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a build-up
of debris.
c) Lower guard may be retracted manually only for special
cuts such as “plunge cuts” and “compound cuts.” Raise
lower guard by retracting handle and as soon as blade enters
the material, the lower guard must be released. For all other
sawing, the lower guard should operate automatically.
d) Always observe that the lower guard is covering the
blade before placing saw down on bench or floor.
An unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of the time
it takes for the blade to stop after switch is released.
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW
1. Only use saw blades recommended in the specification.
2. Do not use any abrasive wheels.
3. Use only blade diameter(s) in accordance with the markings.
4. Identify the correct saw blade to be used for the material to be cut.
5. Use only saw blades that are marked with a speed equal or
higher than the speed marked on the tool.
6. Important information – Product care
NOTE: For any issues related directly to your 20V Li-Ion 165mm
Circular Saw, contact the Customer Service of the manufacturer
as listed on the packaging, manual or on the label on the cordless
circular saw.
This 20V Li-Ion 165mm Circular Saw uses Lithium Ion Battery Cells.
Care MUST be taken to ensure both the safety and life of the pack
is maintained. Ensure you have read all of the safety notes in the
17
17
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
previous pages before using the 20V Li-Ion 165mm Circular Saw.
Treat the battery pack with care and within the guidelines of this
manual.
If the battery pack does become immersed in water or any fluids,
or is subject to a severe drop or it does not operate within the
guidelines of this manual or the supplied manual, immediately STOP
using the battery pack and have it checked.
7. Assembly
NOTE: Before using the tool, read the instruction manual
carefully.
7.1 To remove the battery pack (See Fig. A1)
Depress the battery pack release button (17) firmly, then slide the
battery pack (16) out away from the tool.
7.2 To install the battery pack (See Fig. A2)
Slide the fully charged battery pack (16) onto the tool with
sufficient force until it clicks into position.
A1 A2
18
18
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
8. Operation
8.1 Changing The Saw Blade (See Fig. B1, B2, B3)
WARNING: Before undertaking any maintenance or
adjustment, ensure the battery is removed.
Wear protective gloves when mounting the saw blade.
Danger of injury when touching the saw blade.
Only use saw blades that correspond with the technical
specification data for this tool.
Do not under any circumstances use grinding discs as the
cutting tool.
For changing the saw blade, it is best to place the machine on with
the motor end cap on a flat surface with the blade and blade guard
area facing upwards.
Removing the saw blade
WARNING: Always ensure that the saw is switched of and the
battery pack (16) is removed before making any adjustments.
Press the spindle lock button (4) and keep it depressed.
The spindle lock button (4) may be activated only when the saw
blade (19) is at a standstill.
Loosen the blade bolt (21) in a clockwise direction using the
supplied hex key (24). Remove the outer flange (20). Using the lower
B1 B2 B3
19
19
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
guard lever (12), tilt back the lower blade guard (13) and hold it
firmly in this position. Remove the saw blade (19).(See Fig.B1,B2)
Mounting the saw blade
WARNING: Always ensure that the saw is switched off and the
battery pack (16) is removed before making any adjustments.
Clean the saw blade (19) inner flange (18), outer flange (20) and the
blade bolt (21). Using the lower guard lever (12), tilt back the lower
blade guard (13) and hold it firmly in this position. Place the saw
blade (19) onto the inner flange (18). Ensuring that the direction of
the cutting teeth on the saw blade match the direction of the blade
rotation indicator (25), place the blade over the outer flange (20)
then insert the blade bolt (21). Press in the spindle lock button (4) to
lock the spindle (27), then use the supplied hex key (24) to tighten
the blade bolt (21) in an anti-clockwise direction with 1/4 turn more
than finger tight.
NOTE: Take care that the mounting positions of the inner
flange and outer flange are correct.( See Fig.B3)
NOTE: When mounting: Ensure that the cutting direction of
the teeth (direction of arrow on saw blade) and the blade
rotation indicator (25) on the blade guard match.
8.2 Adjusting the cutting depth (See Fig. C)
WARNING: Always ensure that the saw is switched off and the
battery pack (16) is removed before making any adjustments.
Turn the cutting depth lock knob (23) in an anti-clockwise direction,
and raise the saw body away from the base plate (11). Set the depth
of cut using the cutting depth scale (22) and then turn the cutting
depth lock knob (23) in a clockwise direction to lock. Always add
3mm to your depth of cut so that the blade can cut through the
material.
20
20
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
8.3 Base plate angle adjustment (See Fig. D1, D2)
WARNING: Always ensure that the saw is switched off and the
battery pack (16) is removed before making any adjustments.
Turn the base plate bevel bevel lock knob (6) in an anti-clockwise
direction to loosen the angle scale. Tilt the base plate (11) away
from the machine until the required cutting angle is adjusted on the
base plate angle scale (5). Tighten the base plate bevel lock knob (6)
by turning it in a clockwise direction. Do not use the cutting depth
scale (22) when making bevel cuts due to possible inaccuracy.
C D1 D2
8.4 Dust/chip extraction (See Fig. E)
WARNING: Always ensure that the saw is switched off and the
battery pack (16) is removed before making any adjustments.
To attach the dust extraction adapter (15), place over the dust
extraction port recess area, lining up the screw holes on the adapter
and the holes on the recess. Insert the assembly screws and tighten
in a clockwise direction using a philips head screwdriver (not
supplied). Ensure the fit is secure.
To remove the dust extraction adapter (15), loosen the assembly
screws using a philips head screwdriver (not supplied) in an
anticlockwise direction. Remove the screws, and remove the dust
extraction adapter (15) from the recess.
Directly connect a suitable vacuum hose to the adapter.
NOTE: There is an arrow on the surface of the adapter which shows
which direction to tighten on the hose.
22
23
21
21
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
The dust extraction adapter (15) must not be mounted when
there is no external dust extraction connected. Otherwise
there is danger of the extraction system becoming clogged.
Clean the dust extraction adapter (15) regularly to ensure optimum
dust extraction. The vacuum cleaner / dust extraction device must be
suitable for the material to be worked.
8.5 Hand grip position (See Fig. F)
Always hold your saw firmly with both hands when operating.
E F
8.6 Switching on and off (See Fig. G)
Your switch is locked off to prevent accidental starting. Depress the
lock off button (1) then press in the trigger switch (2) and release
the lock off button (1). The power is now locked on. To switch off,
just release the trigger switch (2).
The blade may continue to rotate after switching off. Wait until the
machine comes to a complete stop before setting down.
8.7 Cutting guide (See Fig. H1, H2)
WARNING: Always ensure that the saw is switched of and the
battery pack (16) is removed before making any adjustments.
There are 2 x cutting mark notches (8 -45°, 9 - 0°) on the front of the
base plate for use with the parallel guide (10). For straight cuts, use
the 0º cutting mark (9) to align with your parallel guide scale. For a
45º bevel cut, use the 45º cutting mark (8) to align the the parallel
guide scale. Always make a trial cut to check the setting.
22
22
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
G H1 H2
0
o
45
o
8.8 Parallel guide adjustment (See Fig. I)
WARNING: Always ensure that the saw is switched off and the
battery pack (16) is removed before making any adjustments.
This is used for making cuts parallel to a workpiece edge at a chosen
distance. Slide the parallel guide (10) arm through the fixture to
achieve the required cutting distance then tighten the parallel guide
locking knob (7) in a clockwise direction to clamp. It can be used from
both sides of the base plate (11). For straight cuts, use the 0° guide
mark to align with the parallel guide scale. For a 45° bevel cut, use the
45° cutting mark (8) to align with your parallel guide scale. Securely
clamp the parallel guide (10).
NOTE: It is best to carry out a trial cut before cutting your work piece.
8.9 Bevel cuts (See Fig. J1, J2)
Set the required bevel angle between 0° and 45°. Do not use the
depth of cut scale when making bevel cuts due to possible inaccuracy.
I
J1 J2
23
23
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
8.10 Hex key storage (See Fig. K)
The supplied hex key (24) provided can be placed in the area under
the machine motor.
K
9. Maintenance
WARNING! Always ensure that the cordless circular saw
is switched off and the battery pack is removed before
making any adjustment.
Your power tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in a dry place. Keep
the motor ventilation slots clean. Keep all working controls free of
dust. Occasionally you may see sparks through the ventilation slots.
This is normal and will not damage your power tool.
10. Warranty
Your new WORKZONE
®
TITANIUM 20V Li-Ion 165mm Circular Saw
will more than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new 20V Li-Ion 165mm Circular Saw easy and safe
24
24
24
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
to operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual
before using your new WORKZONE
®
TITANIUM 20V 165mm Circular
Saw. Take special care to heed the Cautions and Warnings.
Your WORKZONE
®
TITANIUM 20V Li-Ion 165mm Circular Saw has
many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in the
development of this 20V Li-Ion 165mm Circular Saw, making it easy
to maintain and operate.
Use only WORKZONE
®
TITANIUM replacement parts for your
product. Non-conforming parts or modifications made to parts will
void your warranty.
11. Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
What your 5 year warranty means
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly.
In the event of product failure within its intended use over the
course of as quickly as possible once it has been brought to our
attention. In the unlikely event of such an occurrence, or if you
require any information about the product please contact us via
our after sales support services, details of which can be found in this
manual and on the product itself.
After Sales Support TEL: 1300 889 028
25
25
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
Service Support
If you have any issues with the operation of your product, please call us
on 1300 889 028 for advice, or email us at info.aldi@positecgroup.com
Accessories and After Sales Parts
The following is available for purchase by visiting https://help.tools/
or calling our customer service hotline on: 1300 889 028
1. CSC165XA.9-BL: 165mm Blade
12. FAQ/Troubleshooting
Working Hints For Your Cordless Circular Saw
• Always use a blade suited to the material and material thickness
to be cut.
The quality of cut will improve as the number of blade teeth
increase.
• Always ensure the work-piece is firmly held or clamped to prevent
movement.
• Support large panels close to the cut line. Any movement of the
material may affect the quality of the cut.
The blade cuts on the upward stroke and may chip the uppermost
surface or edges of your work piece when cutting,
• Ensure the upper surface is a non visible surface of your work
piece.
26
26
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Troubleshooting
Fault Cause Remedy
The Battery pack gets
warm when charging.
It’s a result of the stepping
down of the chemical
reactions inside the
batteries during the
charging process.
This is normal.
Undiagnosable Fault.
The tool needs to be
repaired.
Return the tool to a
service centre for repair
or contact Customer
Service.
The machine does
not start up when
operating the on/off
switch.
Low battery. Charge the battery.
Defective motor.
Contact Customer
Service.
Cutting depth is less
than is set.
Sawdust accumulated at
the rear of the base.
Shake out sawdust.
Consider connecting
a vacuum for dust
collection.
Blade spins or slips
Blade is not tightly
engaged with the spindle.
Re-assemble the blade as
described in ASSEMBLY
section.
Blade does not cut a
straight line.
Blade is dull.
Mount a new, sharp
blade on the saw.
Blade is not mounted
properly.
Check that blade is
properly mounted.
Saw is not being guided
properly.
Use a parallel guide.
Blade kicks back
when beginning a
cut.
Blade is not spinning fast
enough.
Allow the saw blade to
reach full speed prior to
beginning a cut in the
material.
27
27
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CSC165XA.9 • 2323 • 05/2019
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
Significantly reduced
cutting efficiency.
Low battery. Charge the battery.
Worn blade. Replace a new blade.
Defective motor.
Contact Customer
Service.
The machine is
blocked frequently.
Large size of iron piece in
the workpiece (eg nail).
Check the workpiece.
Low battery. Charge the battery.
Defective motor.
Contact Customer
Service.
Blade guard cannot
open or rebound.
Defective guard.
Contact Customer
Service.
During use, the
machine cannot push
forward.
Workpiece is blocking the
machine.
Check the workpiece.
For further inquiries or issues associated with your tool, call our
Customer Service on 1300 889 028 or email us at
info. aldi@positecgroup.com
28
28
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CSC165XA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
13. Technical specifications
Voltage 20V d.c.
No load speed 4000/min
Blade size 165mm
Cutting capacity:
- Max. Cutting depth at 90° 53mm
- Max. Cutting depth at 45° 36mm
Blade Teeth 24T
Blade Bore 20mm
Blade – Width of cut 1.6mm
Bevel capacity 0-45
o
Machine weight 2.54kg
Product Dimensions (L x W x H)
340 x230 x255mm
Safety:
EN62841-1
EN62841-2-5
AS/NZS62841.1
AS/NZS62841.2.5
EMC:
EN55014-1
EN55014-2
This 20V 165mm Circular Saw complies with the following
Standards:
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
CPS18WA.9
Version number: 004
Cordless Sander
05
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Welcome
Congratulations in choosing to buy a Workzone® Titanium 20V Li-Ion
Cordless Detail Sander.
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of our
philosophy of customer service and satisfaction, are backed by our
comprehensive 5 Year Warranty. We hope you will enjoy your purchase
for many years to come.
When you open your packaging, rst remove all items and check there
are no parts damaged or missing. If you nd anything wrong, do not
operate the product until the parts have been replaced or the fault has
been rectied. Failure to do so could result in serious personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the
date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T
conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
20V Li-Ion Cordless Detail Sander
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Contents
Application 5
Package Content List 5
Parts description 6
Description of symbols 7
Product Safety 8
Important information – Product care 12
Assembly 13
Operation 16
Maintenance 17
Warranty 18
Environmental protection 19
Accessories and after sales parts 19
Frequently Asked Questions 20
Troubleshooting 21
Technical Specications 22
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
1. Application
20V Li-Ion Cordless Sander
2. Package Content List
First time users or inexperienced operators pay particular attention to the
operation of the 20V Li-Ion Cordless Sander, including details of starting and
stopping and correct use of the 20V Li-Ion Cordless Detail Sander on pages
13-17, as well as the maintenance instructions on page 17.
Intended use of 20V Li-Ion Cordless Detail Sander
NOTE: This product is for private domestic DIY use only.
It is not suitable for commercial or trade use.
This 20V Li-Ion Cordless Detail Sander is used for dry sanding of wood, plastic,
ller and coated surfaces.
The sander is to be used only for its prescribed purpose. Any other use is
deemed to be a case of misuse.
1 x 20V Li-Ion Cordless Detail Sander Skin
1 x Dust bag
3 x Sanding paper (60G/80G/120G)
1 x Finger pad
3 x Finger sanding paper (60G/80G/120G)
• Remove all packing materials
• Ensure all parts on the contents
list are present
• Check the appliance, and all
accessories for transportation
damages
WARNING! Please read and understand this instruction manual
before use and keep it for your future reference. Your product
should only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the supplied 20V Li-Ion
battery or charger or any ALDI Xnity Plus 20V Li-Ion battery packs.
Other type of battery packs may burst causing personal injury and
damage. The battery pack must be recharged only with the supplied 20V
Li-Ion charger or any ALDI Xnity Plus 20V Li-Ion battery chargers.
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
3. Parts description
1. On-o switch
2. Soft grip handle
3. Battery pack
4. Dust bag
5. Detail sanding plate
6. Base locking lever
7. SDS Finger pad
8. Dust bag port
9. Hook and Loop base
10. 3 x Sanding paper
(60G/80G/120G )
11. 3 x Finger sanding paper
(60G/80G/120G)
12. Battery pack release button
10
11
5
9
1
2
6
7
4
8
3
12
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
To reduce the risk of injury, user must read instruction
manual
Warning
Wear ear protection
Wear eye protection
Wear breathing protection
Conforms to relevant standards for electrical safety and
electromagnetic compatibility.
60 Months Warranty
60
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
5. Product Safety
General safety warnings
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Keep your hair and clothing away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power
tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained
power tools.
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free
from oil and grease. Slippery handles and grasping surfaces
do not allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of injury
and fire.
c) When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk of
injury.
12
12
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
f) Do not expose a battery pack or tool to fire or excessive
temperature. Exposure to fire or temperature above 130 °C
may cause explosion.
g) Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs. Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
6. Important information – Product care
For any issuses related directly to your Battery / charger, contact
the Customer Service of the manufacturer as listed on the battery /
charger packaging, manual or on the label on the battery / charger.
This Detail Sander uses Lithium Ion Battery Cells. Care MUST be taken
to ensure both the safety and life of the pack is maintained. Ensure you
have read all of the safety notes in the previous pages before using the
Detail Sander.
Treat the battery pack with care and within the guidelines of this manual.
If the battery pack does become immersed in water or any fluids,
or is subject to a severe drop or it does not operate within the
guidelines of this manual or the supplied manual, immediately STOP
using the battery pack and have it checked.
Use only the batteries and charger included with this kit, or any
ALDI 20V Li-Ion Xfinity Plus batteries and chargers.
13
13
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
7. Assembly
NOTE: Before using the tool, read the instruction book
carefully.
7.1. Fitting The Sanding Paper (See Fig. A1, A2)
WARNING: Always ensure that the sander is switched off and
the battery pack is removed before making any adjustments.
Fit the sanding paper (10) over the hook and loop base (9) so that
it covers the entire area. Make sure the sanding paper (10) is even
with the edges of the sanding plate (5), and that the dust collection
holes in the hook and loop base (9) and sanding paper (10) are
aligned.
WARNING: Never use your sander without sandpaper (10)
applied to the detail sanding plate (5)
NOTE: Before fitting a new sanding sheet, remove any dust and dirt
from the detail sander plate.
A1 A2
7.2. Attaching the dust bag (See Fig. B)
WARNING: Always ensure that the sander is switched off and
the battery pack is removed before making any adjustments.
Your sander is equipped with a dust bag (4). To attach, insert the
dust bag (4) into the dust bag port (8) fully until the dust bag (4) is
securely in place.
WARNING: To prevent the possibility of sanding dust or
foreign body being thrown into your face or eyes, never
14
14
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
attempt to use your sander without the dust bag properly installed.
NOTE: Always wear a dust mask.
7.3. Emptying / Removing the dust bag (See Fig. C)
WARNING: Always ensure that the sander is switched off and
the battery pack is removed before making any adjustments.
For more efficient operation, empty the dust bag (4) after every
5-10 minutes of operation. This will permit the air to flow through
the dust bag (4) more effectively. Pull the dust bag (4) out and away
from the rear of the detail sander, and shake out the dust from the
dust bag (4). It is recommended to clean the dust bag (4) regularly
for better performance.
B C
7.4. SDS finger pad (See Fig. D1, D2, D3)
WARNING: Always ensure that the sander is switched off and
the battery pack is removed before making any adjustments.
1) To access the finger pad (7), raise the base locking lever (6)
upwards towards the top of the sander.
2) Pull the SDS finger pad (7) out.
3) To re-secure the SDS finger pad (7) in position, push the base
locking lever (6) down until secure.
15
15
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
D1 D2 D3
7.5. Selecting the right sand paper
Selecting the correct grit of sandpaper is an extremely important
decision that will allow you to achieve the best quality sanding finish.
Coarse grit will remove the most material and finer grit will give you
the best finish in all sanding operations. The condition of the surface
to be sanded will determine which grit will do the job.
If the surface is rough, start with coarse grit and sand until the
surface is uniform. Then use a medium grit to remove any scratches
left by the coarse grit. Complete using a finer grit for finishing the surface.
NOTE: Always continue sanding with each grit until the
surface is uniform.
7.6 To install the battery pack (See Fig. E1)
WARNING: Ensure the on/off switch (1) is in the OFF position
before attaching the battery pack.
Slide the fully charged battery pack (3) onto the sander with
sufficient force until it clicks into position.
7.7 To remove the battery pack (See Fig. E2)
Depress the battery pack release button (12) firmly, then slide the
battery pack (3) out and away from the sander.
16
16
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
E1 E2
1
2
8. Operation
8.1. On/Off Switch (See Fig. F)
To start the sander, press the on/off switch (1) on the position
marked “I”.
To stop the sander, press the on/off switch (1) on the position
marked “O”.
8.2. Flush sanding facility (See Fig. G)
Your sander can sand flush on three sides of the sanding plate which
allows easy access to corners and edges.
F G
17
17
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
8.3. Orbital sanding
Your sander operates in small circular rotations which allows
efficient material removal.
Operate the sander in long sweeping movements across your
workpiece and even across the grain. For a finer finish, always use a
fine grain sandpaper and only move the sander in the direction of
the grain and never across the grain.
Do not allow the sander to remain in the same position otherwise
you will remove material and create an uneven surface.
8.4. SDS finger pad (See fig. H1, H2)
This sander has a finger pad (8), which is suitable for fine sanding in
corners, edges, or hard-to reach areas. Start the sander then apply
the finger pad to the work piece.
H1 H2
9. Maintenance
Remove the battery pack from the tool before carrying out
any adjustment, servicing or maintenance.
Your power tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in a dry place. Keep
the motor ventilation slots clean. Keep all working controls free of
dust. Occasionally you may see sparks through the ventilation slots.
This is normal and will not damage your power tool.
18
18
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
For battery tools
The ambient temperature range for tool and battery use and
storage is 0
o
C-45
o
C.
The recommended ambient temperature range for the charging
system during charging is 0
o
C-40
o
C.
Storage & Transport
Always empty and clean the dust collection box thoroughly upon
completion of a sanding operation before placing the sander in storage.
When storing or transporting the sander ensure the battery is
detached from the sander, and that the on/off switch (1) is in the OFF
position. This prevents any accidental starting of the sander.
10. Warranty
Your new WORKZONE
®
TITANIUM 20V Li-Ion Cordless Detail Sander
will more than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new 20V Li-Ion Cordless Detail Sander easy and
safe to operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual
before using your new WORKZONE
®
TITANIUM 20V Li-Ion Cordless
Detail Sander.
Take special care to heed the Cautions and Warnings.
Your WORKZONE
®
TITANIUM 20V Li-Ion Cordless Detail Sander has
many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in the
development of this 20V Li-Ion Cordless Detail Sander, making it easy
to maintain and operate.
Use only WORKZONE
®
TITANIUM replacement parts for your product.
Non-conforming parts or modifications made to parts will void your
warranty.
19
19
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
What your 5 year warranty means
Great care has gone into the manufacture of this product and it
should therefore provide you with years of good service when used
properly. In the event of product failure within its intended use over
the course of the first 5 years after the date of purchase, we will
remedy the problem as quickly as possible once it has been brought
to our attention. In the unlikely event of such an occurrence, or if
you require any information about the product please contact us via
our after sales support services, details of which can be found in this
manual and on the product itself.
After Sales Support TEL: 1300 889 028
Service Support
If you have any issues with the operation of your product, please call
us on 1300 889 028 for advice, or email us at
info.aldi@positecgroup.com
11. Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
12. Accessories and after sales parts
The following are available for purchase by visiting https://help.tools/
or calling our customer service hotline on: 1300 889 028
1. Various Sandpaper 2. 2323-CPS18WA.9-DB: Dust Bag
20
20
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
13. Frequently Asked Questions
WORK HINTS FOR YOUR SANDER
• If your sander becomes too hot, run it at no load (running just the
motor, and not using it) for 2-3 minutes to cool the motor.
• Always ensure the work-piece is firmly held or clamped to prevent
movement.
Any movement of the material may affect the quality of the sanding
finish.
• Start your sander before sanding and turn off only after stopping
sanding. For best results, sand wood in the direction of the grain.
• Do not start sanding without sandpaper fitted.
• Do not allow the sandpaper to wear away, it will damage the
base-plate. The product warranty does not cover base-plate wear
and tear.
• Use coarse grit paper to sand rough surfaces, medium grit for
smooth surfaces and fine grit for the final surfaces. If necessary, first
make a test on scrap material.
• Use only good quality sandpaper.
• The sanding efficiency is controlled by the sandpaper not the
amount of force you apply to the tool. Excessive force will reduce
the sanding efficiency and cause motor overload.
• Replacing the sanding paper regularly will maintain optimum
sanding efficiency.
• Do NOT sand asbestos material in ANY form.
• Always wear a dust mask, hearing protection and safety eye
protection during sanding procedures.
• Sand hard-to-reach places using the SDS finger pad (7).
• Check and empty the dust bag (4) at regular intervals.
21
21
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CPS18WA.9 • 2323 • 05/2019
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
14. Troubleshooting
Fault Cause Remedy
The Battery pack gets
warm when charging.
It’s a result of the stepping
down of the chemical reactions
inside the batteries during the
charging process.
This is normal.
Undiagnosable Fault. The tool needs to be repaired.
Contact Customer
Service
Low efficiency in
sanding
Too much dust in the dust bag.
Clean and empty
the dust bag.
The sander does not
start up after turning
on.
Battery depleted. Charge the battery.
Defective on/off switch.
Contact Customer
Service.
Defective motor.
Contact Customer
Service.
The sander stops
during use.
Low battery. Charge the battery.
Workpiece sanding is
not smooth. Sanding
marks are appearing .
Rough sanding paper. The
density of grit is too low.
Change to a proper
sanding paper with
a higher grit.
Low sanding efficiency.
Worn sanding paper.
Replace it with new
sanding paper.
The density of grit of the
sanding paper is too high.
Change to a
sanding paper with
lower grit.
22
22
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CPS18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
15. Technical specifications
Voltage 20V d.c.
No load speed 13000/min
Base size 140*140*80mm
Orbital diameter 1.5mm
Tool weight 1.23kg
Product Dimensions (L x W x H):
260 x125 x120mm
Safety: IEC 62841-1
IEC 62841-2-4
AS/NZS 62841.1
AS/NZS 62841.2.4
EMC: EN 55014-1
EN 55014-2
This 20V Li-ion Cordless Detail Sander complies with the
following Standards:
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
CLP18WA.9
Version number: 004
Cordless LED Torch
06
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Welcome
Congratulations in choosing to buy a Workzone® Titanium 20V Li-Ion
Cordless LED torch.
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of our
philosophy of customer service and satisfaction, are backed by our
comprehensive 5 Year Warranty. We hope you will enjoy your purchase
for many years to come.
When you open your packaging, rst remove all items and check there
are no parts damaged or missing. If you nd anything wrong, do not
operate the product until the parts have been replaced or the fault has
been rectied. Failure to do so could result in serious personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the
date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T
conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
20V Li-Ion Cordless LED torch
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Contents
Application 5
Package Content List 5
Parts description 6
Description of symbols 7
General safety warnings 8
Important information-Product care 10
Assembly 10
Operation 11
Maintenance 14
Warranty 15
Environmental protection 16
FAQ/Troubleshooting 17
Technical Specications 18
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
1. Application
20V Li-Ion Cordless LED Torch
2. Package Content List
First time users or inexperienced operators pay particular attention to the
operation of the 20V Li-Ion Cordless LED Torch, including details of starting
and stopping and correct use of the 20V Li-Ion Cordless LED Torch on pages
10-13, as well as the maintenance instructions on page 14.
Intended use of 20V Li-Ion LED torch
NOTE: This product is for private domestic DIY use only. It is not suitable for
commercial or trade use.
This 20V Li-Ion Cordless LED Torch is used for lighting.
1 x 20V Li-Ion Cordless LED Torch Skin
1 x Belt clip + assembly screw
(not tted)
1 x Hanging hook (tted)
1 x Instruction Manual
1 x Warranty Card
• Remove all packing materials
• Ensure all parts on the contents
list are present
• Check the appliance, and all
accessories for transportation
damages
WARNING! Please read and understand this instruction manual
before use and keep it for your future reference. Your power tool
should only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the supplied battery or
any 20V Li-Ion Xnity Plus batteries. Other type of battery packs may
burst causing personal injury and damage. The battery pack must be
recharged only with the supplied 20V Li-Ion charger, or any ALDI 20V
Li-Ion Xnity Plus charger.
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
3. Parts description
1. LED light
2. Torch head
3. Pivot joint
4. ON/OFF Switch
5. Handle
6. Belt clip retainer
7. Battery pack release button
8. Battery Pack
9. Hanging hook
10. Belt clip
7
8
9
6
5
3
2
10
4
1
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
Warning
To reduce the risk of injury, user must read instruction manual.
Class III
Do not stare at the operating light source
60 Months Warranty
Replace any cracked protective shield
Regulatory Compliance Mark. Appliance complies with
requirements of electrical approval & EMC in Australia.
60
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
5. General safety warning
SAFETY POINTS FOR YOUR FLASHLIGHT/ WORKLIGHT
SAFETY RULES FOR CORDLESS PORTABLE HAND-HELD LIGHT
CHARGE BATTERY BEFORE FIRST USE
CAUTION: Read, understand and follow all Safety Rules and
Operating Instructions in this Manual before using this product.
SAVE THESE INSTRUCTIONS!
READ ALL INSTRUCTIONS!
SAFETY INSTRUCTIONS
WARNING: Be sure to read and understand all
instructions in this manual before using this portable
hand-held light. Failure to follow all instructions may result
in electric shock, fire and/or serious personal injury.
1. Know your cordless portable hand-held light. Read
operator’s manual carefully.
Learn its applications and limitations, as well as the specific
potential hazards related to this light.
2. Use only recommended battery pack and charger.
Any attempt to use another battery pack will cause damage to
the portable hand-held light and could possible explode, cause a
fire, or personal injury.
Model Battery Pack charger
CLP18WA.9 ABP1815MA JLH122200370S&Z10
3. Remove battery pack from portable hand-held light
before replacing bulb or performing any routine
maintenance or cleaning.
4. Do not disassemble the portable hand-held light.
5. Do not place portable hand-held light or battery pack near fire
or heat. They may explode. Also, do not dispose of a worn out
battery pack by incineration, even if it is severely damaged or
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
completely worn out. The battery may explode in fire.
6. Do not operate portable hand-held light or charging
stand/transformer near flammable liquids or in gaseous
or explosive atmospheres. Internal sparks may ignite fumes.
7. To reduce the risk of electric shock, do not put portable
hand-held light in water or other liquid. Do not place or
store portable hand-held light where it can fall or be pulled into
a tub or sink.
8. Do not permit children to use portable hand-held light
unsupervised. It is not a toy. The temperature of the bulb
will become hot after being on only a short period of time. This
hot temperature can cause burn injury if touched.
9. DO NOT USE OR PERMIT USE OF PORTABLE HAND-HELD
LIGHT IN BED OR SLEEPING BAGS. This portable hand-held
light lens can melt fabric and a burn injury could result.
10. Keep light dry, clean, and free from oil and grease. Always
use a clean cloth when cleaning. Never use brake fluid, gasoline,
petroleum-base products or any strong solvent to clean the
portable hand-held light.
11. The light source of this luminaire is not replaceable;
when the light source reaches its end of life the whole
luminaire shall be replaced.
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
6. Important information – Product care
This LED torch uses Lithium Ion Battery Cells. Care MUST be taken to
ensure both the safety and life of the pack is maintained. Ensure you
have read all of the safety notes in the previous pages before using
the LED Torch.
Treat the battery pack with care and within the guidelines of this manual
If the battery pack does become immersed in water or any fluids,
or is subject to a severe drop or it does not operate within the
guidelines of this manual or the supplied manual, immediately stop
using the battery pack and have it checked.
7. Assembly
NOTE: Before using the tool, read the instruction book
carefully.
There is no assembly required for use of this LED Torch.
7.1 Charging your Battery pack (8)
WARNING: The charger and battery pack (8) are specially designed
to work together so do not attempt to use any other devices.
Never insert or allow metallic objects into your charger or battery pack
(8) connections because an electrical failure and hazard will occur.
Note:
a)
Do not use any charger other than that specifically provided for use
with the equipment, or any 20V Li-Ion ALDI Xfinity Plus Batteries.
b) If the battery pack (8) is very hot, remove the battery pack (8)
from the charger and allow time for the battery to cool down
before recharging.
c) The battery pack (8) in your new tool is not charged when it
leaves the manufacturer. Therefore it must be fully charged
before using for the first time.
d) Charge the battery pack (8) to reach full or no less than half
charge before storage. If the tool will not be used for long
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
periods of time, charge the battery every 3-6 months.
7.2 To remove the battery pack (See Fig. A1)
Depress the battery pack release button (7) firmly, then slide the
battery pack (8) out away from the LED torch.
7.3 To install the battery pack (See Fig. A2)
Slide the fully charged battery pack (8) onto the LED torch with
sufficient force until it clicks into position.
8.Operation
8.1 ON/OFF Switch(4)
Press the on/off switch (4) to turn on the LED Torch. (See Fig. B)
Press the on/off switch (4) again to turn OFF the LED Torch. (See Fig.
B)
ON/OFF
Switch
A1 A2
B
12
12
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
8.2 Adjusting the Torch Head (2) position.
Adjust the torch head (2) position by rotating the pivoting head
from the pivot joint (3). (See Fig. C) The torch pivoting head rotates
to provide light in the range of -10° to 100°.
8.3 Carrying and Suspending the torch
CAUTION: When the LED Torch hangs by the belt clip (10)
or the hanging hook (9). Do not shake the LED Torch or the
object from which it hangs. Do not hang the torch from any
electrical wires or anything that is not secure. Personal injury
or property damage may occur.
CAUTION: Only use the belt clip (10) or the hanging hook (9)
for hanging the LED Torch. The belt clip (10) and hanging
hook (9) are not intended to support additional weight. Do
not attach or hang anything additional to the torch or risk
breakage may occur.
CAUTION: Do not use the belt clip (10) or hanging hook (9) to
reach with or to support your weight in any situation.
8.4 Hanging hook (9)
The torch may be carried or hung by the hanging hook (9) (See Fig.
D1). When not in use, the hanging hook (9) may be folded down
(See Fig. D2).
C
13
13
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
8.5 Belt clip (10) (See Fig. E)
WARNING! To reduce the risk of serious personal injury,
ensure the screw holding the belt clip (10) is secure.
The side belt clip (10) is used to assist to clip the torch to your waist
belt while working. To install, insert the assembly screw through the
belt clip screw hole into the retaining hole on the torch, and using a
philips head screwdriver (not supplied), tighten the screw by turning
in a clockwise direction
NOTE: The belt clip (10) can be assembled onto either side of the
LED torch.
IMPORTANT: When attaching or replacing the belt clip (10), use
only the assembly screw that is provided. Be sure to securely tighten
screw.
D1 D2
E
9
9
14
14
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
9.Maintenance
Warning! Always ensure that the LED Torch is switched
off and the battery pack is removed before making any
adjustment.
Cleaning
Your LED torch requires no additional lubrication or maintenance.
There are no user serviceable parts in your LED torch. Never use
water or chemical cleaners to clean your LED torch. Wipe clean with
a dry cloth. Always store your power tool in a dry place. Keep all
working controls free of dust.
Storage & Transport
When not in use, the LED Torch should be stored in a dry, frost free
location not within the reach of children.
When storing or transporting the LED Torch ensure the battery is
detached from the torch. This prevents any accidental starting of
the LED Torch.
For Battery tools
The ambient temperature range for the use and storage of tool and
battery is 0°C-45°C.
The recommended ambient temperature range for the charging
system during charging is 0°C-40°C.
15
15
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
10.Warranty
Your new WORKZONE
®
TITANIUM 20V Li-Ion LED Torch will more
than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new 20V Li-Ion LED Torch easy and safe to
operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual
before using your new WORKZONE
®
TITANIUM 20V Li-Ion LED Torch.
Take special care to heed the Cautions and Warnings.
Your WORKZONE
®
TITANIUM 20V Li-Ion LED Torch has many features
that will make your job faster and easier. Safety, performance, and
dependability have been given top priority in the development of
this 20V Li-Ion Cordless LED Torch, making it easy to maintain and
operate.
Use only WORKZONE
®
TITANIUM replacement parts for your
product. Non-conforming parts or modifications made to parts will
void your warranty.
16
16
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
What your 5 year warranty means
Great care has gone into the manufacture of this product and it
should therefore provide you with years of good service when used
properly.
In the event of product failure within its intended use over the
course of as quickly as possible once it has been brought to our
attention. In the unlikely event of such an occurrence, or if you
require any information about the product please contact us via
our after sales support services, details of which can be found in this
manual and on the product itself.
After Sales Support TEL: 1300 889 028
Service Support
If you have any issues with the operation of your product, please call
us on 1300 889 028 for advice, or email us at
info.aldi@positecgroup.com
11.Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
17
17
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
CLP18WA.9 • 2323 • 05/2019
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
12. FAQ/Troubleshooting
Fault Cause Remedy
The Battery pack
gets warm when
charging
It’s a result of the stepping
down of the chemical
reactions inside the
batteries during the
charging process
This is normal
Undiagnosable
fault
The tool needs to be
repaired
Contact Customer
Service
18
18
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
CLP18WA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
13. Technical Specification
Rated Voltage 20V d.c.
Rated Power 3 W
Lumen 250LM
Running time 8 h
Machine weight 0.71 kg
Product Dimensions (L x W x H) 150*75*240 mm
Safety: EN 60598-1
EN 60598-2-4
EN 62493
AS/NZS 60598.1
AS/NZS 60598.2.4
EMC: EN 55015
EN 61547
EN 61000-3-2
EN 61000-3-3
This 20V Li-ion Cordless LED torch complies with the
following Standards:
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
TRD18SA.9
Version number: 004
Bluetooth Speaker
07
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Welcome
Congratulations in choosing to buy a Workzone® Titanium 20V Li-Ion
Bluetooth Speaker.
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of our
philosophy of customer service and satisfaction, are backed by our
comprehensive 5 Year Warranty. We hope you will enjoy your purchase
for many years to come.
When you open your packaging, rst remove all items and check there
are no parts damaged or missing. If you nd anything wrong, do not
operate the product until the parts have been replaced or the fault has
been rectied. Failure to do so could result in serious personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the
date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T
conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
20V Li-Ion Bluetooth Speaker
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Contents
Application 5
Package Content List 5
Parts description 6
Description of symbols 7
General Safety Warnings 8
Important information – Product care 9
Assembly 10
Operation 11
Maintenance 13
Warranty 14
Environmental protection 15
FAQ/Troubleshooting 16
Technical Specications 17
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
1. Application
20V Li-Ion Bluetooth Speaker
2. Package Content List
First time users or inexperienced operators pay particular attention to the
operation of the 20V Li-Ion Bluetooth Speaker, including details of starting
and stopping and correct use of the 20V Li-Ion Bluetooth Speaker on pages
11-12, as well as the maintenance instructions on page 13.
Intended use of 20V Li-Ion Bluetooth Speaker
NOTE: This product is for private domestic DIY use only. It is not suitable for
commercial or trade use.
The 20V Li-Ion Bluetooth Speaker is intended for playing music or amplifying
the sound by connecting other Bluetooth-enabled electronic devices.
1 x 20V Li-Ion Bluetooth Speaker
1 x Instruction manual
1 x Warranty Card & Certicate
• Remove all packing materials
• Ensure all parts on the contents
list are present
• Check the appliance, and all
accessories for transportation
damages
WARNING! Please read and understand this instruction manual
before use and keep it for your future reference. Your product should
only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the supplied 20V Li-Ion
battery or charger or any ALDI Xnity Plus range of 20V Li-Ion battery
packs. Other type of battery packs may burst causing personal injury
and damage. The battery pack must be charged using with ALDI
Xnity Plus 20V Li-Ion battery chargers.
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
3. Parts description
1. Bluetooth speaker
2. Battery pack
3. Battery pack release button
4. On/O, Pause/Play Switch
5. Volume adjustment buttons
6. Power indicator light
Volume adjustment buttons: (the left volume button is to decrease volume
and is also used to revert to the previous song; the right volume button is to
increase volume and is also used to play the next song)
5
4
3
6
2
1
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
To reduce the risk of injury, user must read instruction manual
Warning
CAUTION: To prevent electric shock hazard, do not connect
to mains power supply while grille is removed.
Electric shock
Conforms to relevant standards for electrical safety and
electromagnetic compatibility.
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
5. General safety warning
SAFETY WARNING
SAVE THESE INSTRUCTIONS!
READ ALL INSTRUCTIONS!
Safety instructions
WARNING: READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result in
electric shock, fire and / or serious personal injury.
1) Do not use this apparatus near water.
2) Clean only with dry cloth.
3) Ventilation should not be impeded by covering any open vents
on the product.
4) Do not use near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
5) Only use attachments/accessories specified by the manufacturer.
6) Remove the battery during lightning storms or when unused for
long periods of time.
7) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
8) The apparatus shall not be exposed to dripping or, splashing and
that no objects filled with liquids, such as vases, shall be placed
on the apparatus.
9) The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
CAUTION: Danger of explosion if a non specified battery is used on
this product. Use only the supplied 20V Li-Ion battery or any ALDI
Xfinity Plus 20V Li-Ion batteries.
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
6. Important information – Product care
NOTE: For any issues related directly to your 20V Li-Ion Bluetooth
Speaker, contact the Customer Service of the manufacturer as listed
on the 20V Li-Ion Bluetooth Speaker packaging, manual or on the
label on the 20V Li-Ion Bluetooth Speaker.
This 20V Li-Ion Bluetooth Speaker uses Lithium Ion Battery Cells.
Care must be taken to ensure both the safety and life of the pack
is maintained. Ensure you have read all of the safety notes in the
previous pages before using the 20V Li-Ion Bluetooth Speaker.
Treat the battery pack with care and within the guidelines of this
manual.
If the battery pack does become immersed in water or any fluids,
or is subject to a severe drop or it does not operate within the
guidelines of this manual or the supplied manual, immediately stop
using the battery pack and have it checked.
Use only the supplied 20V Li-Ion battery and charger or any ALDI
Xfinity Plus 20V range of batteries and chargers.
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
7. Assembly
NOTE: Before using the bluetooth speaker, read the
instruction book carefully.
7.1 To Remove the Battery Pack (See Fig. A1)
Depress the battery pack release button (3) firmly, then slide the
battery pack (2) out away from the bluetooth speaker.
7.2 To Install the Battery Pack (See Fig. A2)
Slide the fully charged battery pack (2) onto the bluetooth speaker
with sufficient force until it clicks into position.
A1 A2
1
2
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
8. Operation
8.1. ON/OFF SWITCH (SEE FIG. B)
1. Install the battery pack (2).
2. Press the On/Off switch (4) for approx. 3 seconds to turn on power
for the bluetooth speaker (1). You will hear a sound, and the power
indicator light (6) will illuminate flashing blue. The light will flash
quickly in 0.5 second intervals.
3. Press the On/Off switch (4) for approx. 3 seconds to turn off power
for the bluetooth speaker (1). You will hear a sound, and the power
indicator light (6) will turn off.
4. When the battery is low on charge or nearly empty, the power
indicator light (6) will flash quickly.
8.2 Connecting Electronic Device
1. Turn on power to the Bluetooth function of your electronic
device.
2. Find “Bluetooth Speaker” shown on your device and link to it.
When you link to the bluetooth speaker (1) it will make a sound,
and the light will start flashing slower.
3. Once the bluetooth speaker (1) is connected to your device and
playing music, the power indicator light (6) will remain constant and
will not be flashing.
B
12
12
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
8.3 Adjusting the Volume (SEE FIG. C1, C2)
1. Press the right button (5) to increase the volume. When the
bluetooth speaker (1) has reached its maximum volume, you will
hear a beep, and the power indicator light (6) will flash once.
2. Press the left button (5) to lower the volume. When the bluetooth
speaker (1) is at the lowest volume, you will hear a beep, and the
power indicator light (6) will flash slowly.
8.4 Selecting the Functions
1. Quick pressing of the On/Off switch (4) will pause the music being
played on the bluetooth speaker (1). By quickly pressing the On/Off
switch (4) again, the music will resume.
2. By pressing the right volume button (5) for approx. 3 seconds, you
will proceed to the next song.
3. By pressing the left volume button (5) for approx. 3 seconds will
return to the previous song.
C1 C2
13
13
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
9. Maintenance
Warning! Always ensure that the 20V Li-Ion Bluetooth
speaker is switched off and the battery pack is removed
before making any adjustment.
Your Bluetooth speaker requires no additional lubrication or
maintenance.
There are no user serviceable parts in your Bluetooth speaker. Never
use water or chemical cleaners to clean your Bluetooth speaker.
Wipe clean with a dry cloth. Always store in a cool, dry place.
Storage & Transport
When not in use, the Bluetooth speaker should be stored in a dry,
frost free location not within the reach of children.
When storing or transporting the Bluetooth speaker ensure the
battery is detached from the speaker. This prevents any accidental
starting of the Bluetooth speaker.
For Battery tools
The ambient temperature range for the use and storage of tool and
battery is 0°C-45°C.
The recommended ambient temperature range for the charging
system during charging is 0°C-40°C.
14
14
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
10. Warranty
Your new WORKZONE
®
TITANIUM 20V Li-Ion Bluetooth Speaker will
more than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new 20V Li-Ion Bluetooth Speaker easy and safe
to operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual
before using your new WORKZONE
®
TITANIUM 20V Li-Ion Bluetooth
Speaker. Take special care to heed the Cautions and Warnings.
Your WORKZONE
®
TITANIUM 20V Li-Ion Bluetooth Speaker has
many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in the
development of this 20V Li-Ion Bluetooth Speaker, making it easy to
maintain and operate.
Use only WORKZONE
®
TITANIUM replacement parts for your
product. Non-conforming parts or modifications made to parts will
void your warranty.
15
15
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
What your 5 year warranty means
Great care has gone into the manufacture of this product and it
should therefore provide you with years of good service when used
properly.
In the event of product failure within its intended use over the course
of as quickly as possible once it has been brought to our attention.
In the unlikely event of such an occurrence, or if you require any
information about the product please contact us via our after sales
support services, details of which can be found in this manual and on
the product itself. After Sales Support TEL: 1300 889 028
Service Support
If you have any issues with the operation of your product, please call us
on 1300 889 028 for advice, or email us at info.aldi@positecgroup.com
11.Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
16
16
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
12. FAQ/Troubleshooting
Fault Cause Remedy
The Battery pack
gets warm when
charging.
It’s a result of the stepping
down of the chemical
reactions inside the batteries
during the charging process.
This is normal.
Undiagnosable
Fault.
The tool needs to be
repaired.
Contact Customer
Service.
Mobile device
cannot be linked
to the speaker by
Bluetooth.
The speaker has already
been linked to another
device.
Check and disconnect the
Bluetooth connectivity of
the other device.
The device is placed too far
away from the speaker.
Place nearer to the
speaker.
Defective Bluetooth
function.
Contact Customer
Service.
Strong electromagnetic
interference in the
environment
Check what the source
of interference is. It may
be charger or computer
or any high-powered
household electrical
appliances. Place the
speaker far away from
the source.
The speaker switch
off automatically.
Low battery. Charge the battery.
Defective battery.
Contact Customer
Service, or the battery
manufacturer.
For further inquiries or issues associated with your tool, call our Customer
Service on 1300 889 028 or email us at info.aldi@positecgroup.com
17
17
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
TRD18SA.9 • 2323 • 05/2019
MODEL No.:
TRD18SA.9 • 2323 • 05/2019
13. Technical Specifications
Voltage 20V d.c.
Bluetooth version 4.2
Machine weight 0.24 Kg
Product Dimensions (L x W x H): 125x75x95 mm
Safety: IEC 60065
AS/NZS 60065
EMC: EN55032
EN55035
EN 61000-3-2
EN 61000-3-3
EMF: EN 50663
EN 62479
RED: EN 300 328
EN 301 489-1
EN 301 489-17
This 20V Li-Ion Bluetooth Speaker complies with the
following Standards:
Xfinity Li-ION 20V
Instruction Manual
IMPORTANT
Read carefully before use
Keep for future reference
MODEL NUMBER
ACG118PA
Version number: 004
USB CHARGER
08
2
2
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
ACG118PA • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
Welcome
Congratulations in choosing to buy a Workzone® Titanium 20V Li-Ion
USB Charger
All products bought to you by Workzone® Titanium are manufactured
to the highest standards of performance and safety and, as part of
our philosophy of customer service and satisfaction, are backed by
our comprehensive 5 Year Warranty. We hope you will enjoy your
purchase for many years to come.
When you open your packaging, rst remove all items and check
there are no parts damaged or missing. If you nd anything wrong,
do not operate the product until the parts have been replaced or
the fault has been rectied. Failure to do so could result in serious
personal injury.
3
3
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
ACG118PA • 2323 • 05/2019
MODEL No.:
ACG118PA • 2323 • 05/2019
Contents
Application 4
Package Content List 4
Parts description 5
Description of symbols 6
General safety warnings 7
Important information – Product care 8
Operation 8
Maintenance 9
Warranty 9
Environmental protection 10
FAQ/Troubleshooting 11
Technical Specications 11
4
4
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
ACG118PA • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
1. Application
20V Li-Ion USB Charger
2. Package Content List
First time users or inexperienced operators pay particular attention to the
operation of the 20V Li-Ion USB Charger, including details of starting and
stopping and correct use of the 20V Li-Ion USB Charger on page 8, as well as
the maintenance instructions on page 9.
Intended use of 20V Li-Ion USB Charger
NOTE: This product is for private domestic DIY use only. It is not suitable for
commercial or trade use.
This 20V Li-Ion USB Charger is used for charging or supplying power to
mobile phones (Android and iPhone) or any USB device that meets the
technical parameter of 5V Output.
1 x 20V Li-Ion USB Charger
1 x Instruction manual
1 x Warranty Card & Certicate
• Remove all packing
materials
• Ensure all parts on the
contents list are present
• Check the appliance,
and all accessories for
transportation damages
WARNING! Please read and understand this instruction manual before
use and keep it for your future reference. Your 20V Li-Ion USB Charger
should only be passed on together with this instruction manual.
WARNING! To reduce risk of injury, only use the supplied battery
and charger in this kit or any ALDI Xnity Plus range of 20V battery
packs. Other type of battery packs may burst causing personal injury
and damage. The battery pack must be charged using ALDI Xnity
Plus 20V battery chargers.
5
5
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
ACG118PA • 2323 • 05/2019
MODEL No.:
ACG118PA • 2323 • 05/2019
3. Parts description
1. Charging turn on button
2. Charger base
3. USB charging ports
4. Battery pack
5. Battery power indicator
6. Battery pack release button
5 1
2
3
4
6
6
6
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
ACG118PA • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
4. Description of symbols
The instruction manual, rating plate, or on the product itself, may
show these symbols. These represent important information about
the product or instructions on its use.
Warning
For indoor use only
Read the operator’s manual.
Conforms to relevant standards for electrical safety and
electromagnetic compatibility.
60 Months Warranty
Fuse
60
T 2A
7
7
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
ACG118PA • 2323 • 05/2019
MODEL No.:
ACG118PA • 2323 • 05/2019
5. General safety warning
General Safety Warnings
WARNING Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
- This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
- Children should be supervised to ensure that they do not play
with the appliance.
Additional safety instructions for your charger
1. Before charging, read the instructions.
2. Do not use charger for works other than those for which they
are designed.
3. The charging device must be protected from moisture.
4. Do not use the charging device in the open.
5. Do not open the unit and keep out of the reach of children.
6. Ensure that the connection between the charger and your
equipment is correctly positioned.
7. Keep charger’s slots free of foreign objects and protect against
dirt and humidity. Store in a dry and frost-free place.
8. When charging your equipment, ensure that the charger
is in a well-ventilated area and away from inflammable
materials. Ensure that your equipment and charger are not left
unsupervised during charging.
9. Longer life and better performance can be obtained if your
equipment is charged when the air temperature is between 15
o
C
and 25
o
C. Do not charge your equipment in air temperatures
8
8
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
ACG118PA • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
below 0
o
C, or above 40
o
C.
10. Disconnect from your equipment when not charging or the
charging is over.
6. Important information – Product care
NOTE: For any issuses related directly to your Battery, contact the
Customer Service of the manufacturer as listed on the battery
packaging, manual or on the label on the battery.
This Charger uses Lithium Ion Battery Cells. Care MUST be taken to
ensure both the safety and life of the pack is maintained. Ensure you
have read all of the safety notes in the previous pages before using
the Charger.
Treat the battery pack with care and within the guidelines of this
manual.
If the battery pack does become immersed in water or any fluids,
or is subject to a severe drop or it does not operate within the
guidelines of this manual or the supplied manual, immediately STOP
using the battery pack and have it checked.
7. Operation
7.1. To install or remove the battery pack
To install the battery pack
Slide the fully charged battery pack (4) onto the USB Charger with
sufficient force until it clicks into position.
To remove the battery pack
Depress the battery pack release button (6) firmly, then slide the
battery pack (4) out away from the USB charger.
NOTE: Remove the USB charger from the battery pack (4) when not
in use.
7.2. USB Charging Ports (6)
The USB charger is equipped with 2 USB charging ports (3) and
delivers 2.0 A total current per USB port.
9
9
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
ACG118PA • 2323 • 05/2019
MODEL No.:
ACG118PA • 2323 • 05/2019
NOTE: To achieve longer USB charger life, don’t plug in mobile
phones or other devices that exceed charging current on the battery
charger’s label. To charge, insert the USB plug into one of the
charging ports (3).
7.3. Charging Turn On Button (1)
Your charger is equipped with a charging turn on button (1).
First install the USB charger onto a battery pack, then connect your
USB charging cable end into one of the charging ports (3). Press the
charging turn on button (1) to start charging. The battery power
indicator (5) will illuminate for three seconds to show the battery
power. During charging, press the charging turn on button (1) to
check the battery power remaining.
8. Maintenance
There are no serviceable parts inside your battery charger.
Any adjustment, servicing or maintenance should be performed by
an authorized repair agent, so do not attempt to repair your battery
charger.
The USB Charger requires no additional lubrication or maintenance.
Never use water or chemical cleaners to clean your USB Charger.
Wipe clean with a dry cloth. Always store your USB Charger in a dry
place.
9. Warranty
Your new WORKZONE
®
TITANIUM 20V Li-Ion USB Charger will more
than satisfy your expectations.
It has been manufactured under stringent WORKZONE
®
TITANIUM
Quality Standards to meet superior performance criteria.
You will find your new 20V Li-Ion USB Charger easy and safe to
operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual
10
10
AFTER SALES SUPPORT
1300 889 028 (toll free)
MODEL No.:
ACG118PA • 2323 • 05/2019
e-mail:
info.aldi@positecgroup.com
before using your new WORKZONE
®
TITANIUM 20V Li-Ion USB
Charger. Take special care to heed the Cautions and Warnings.
Your WORKZONE
®
TITANIUM 20V Li-Ion USB Charger has
many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in
the development of this 20V Li-Ion USB Charger, making it easy to
maintain and operate.
Use only WORKZONE
®
TITANIUM replacement parts for your
product. Non-conforming parts or modifications made to parts will
void your warranty.
10. Environmental protection
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling centre and disposed of in an
environmentally safe way.
What your 5 year warranty means
Great care has gone into the manufacture of this product and it
should therefore provide you with years of good service when used
properly.
In the event of product failure within its intended use over the
course of as quickly as possible once it has been brought to our
attention. In the unlikely event of such an occurrence, or if you
require any information about the product please contact us via
our after sales support services, details of which can be found in this
manual and on the product itself.
After Sales Support TEL: 1300 889 028
Service Support
If you have any issues with the operation of your product, please call
us on 1300 889 028 for advice, or email us at
info.aldi@positecgroup.com
11
11
AFTER SALES SUPPORT
1300 889 028 (toll free)
e-mail:
info.aldi@positecgroup.com
ACG118PA • 2323 • 05/2019
MODEL No.:
ACG118PA • 2323 • 05/2019
11. FAQ/Troubleshooting
Fault Cause Remedy
The Battery pack
gets warm when
charging.
It’s a result of the stepping
down of the chemical reactions
inside the batteries during the
charging process.
This is normal.
The fault cannot
be rectified.
The tool needs to be repaired.
Contact Customer
Service.
USB port is not
charging
Battery has no charge
Recharge the
battery
The USB plug being used
exceeds the output requirement
of the USB charger.
Do not use this
plug on this device
For further inquiries or issues associated with your tool, call our Customer
Service on 1300 889 028 or email us at info.aldi@positecgroup.com
12. Technical Specifications
Input 20V d.c. 1.5Ah
Output 5VDC 2A(in total)
USB charging port 2
Tool Weight 0.08 kg
Product Dimensions (L x W x H)
125 x 75 x 65mm
This 20V Li-Ion USB charger complies with the following Standards:
Safety:
IEC62368-1
AS/NZS 62368.1
EMC:
EN55035
EN55032
ALDI guarantees that our exclusive brand products are
developed to our stringent quality specifications. If you are
not entirely satisfied with this product, please return it to your
nearest ALDI store within 60 days from the date of purchase
for a full refund or replacement, or take advantage of our after
sales support by calling the supplier‘s Customer Service Hotline.
WORKZONE
®
TITANIUM is a registered trademark of ALDI Stores
Made in China
WORKZONE
®
TITANIUM is a registered trademark of ALDI Stores
DISTRIBUTED BY:
ALDI STORES
1 SARGENTS ROAD, MINCHINBURY NSW 2770
www.aldi.com.au
AUS
1300 889 028
info.aldi@positecgroup.com
05/2019
2323CKT718A
… 168

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Workzone CKT718A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Workzone CKT718A in de taal/talen: Engels als bijlage per email.

De handleiding is 12,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info