724617
19
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
16V Lithium-ion Cordless Drill
AFTER SALES SUPPORT
(toll free) MODEL No.: CDT214XA • 05/2019 • 1956
e-mail: info.aldi@positecgroup.com
AUS
17
1300 889 028
AUS
CAUTION. Do not continue to overload the drill/driver and constantly reset the
overload. Doing this will cause the battery cells to over heat.
Temperature cut out
If the drill/driver is constantly overloaded, or the drill/driver is used constantly at
maximum rating in high ambient conditions, the battery cells may overheat causing
the battery pack to shut down.
When this occurs you will need to allow the battery cells to cool.
NOTE: The drill/driver will not restart until the battery pack has cooled. To reduce the
temperature of the cells remove the battery pack from the drill/driver and place the
battery pack in a free air environment, out of direct sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in refrigerators or freezers.
When the battery pack has cooled down it can again be used to operate the
drill/driver, as long as the load or the conditions causing the original excessive
temperature has been corrected.
Low voltage cut out
The battery pack used on this tool is tted with a low voltage cut out feature within
the circuitry.
The low voltage cut out feature operates when the voltage drops below a preset
value. This feature automatically stops the drill/driver from operating (similar to that
of the overload condition). When this condition occurs you will need to either insert
another battery into the drill/driver or recharge the existing battery.
The low voltage cut out feature has been added to maximise the life of the battery
cells in the battery (8). When this occurs, recharge the battery pack by following the
battery charging section in this manual.
NOTE: Attempting to restart the tool without either recharging the battery or
installing another battery (with charge) will lead to drill/driver restarting and then
stopping again, after only a few seconds of operation.
Ambient temperature ranges
The ambient temperature range for tool, battery use and storage is 0
o
C-45
o
C.
The recommended ambient temperature range for the charging system during
charging is 0
o
C-40
o
C.
Operation
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Workzone CDT214XA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Workzone CDT214XA in de taal/talen: Engels als bijlage per email.

De handleiding is 2,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info