697438
56
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
56
Fault finding and diagnosis
GREENSPRING CWi47 – 6 720 646 322 (2015/04)
Hot water temperature sensor (NTC) on
the hot water outlet of the appliance
detect a high temperature of the hot
water.
Temperature > 85 °C
1. Check the sensor is located and fixed correctly.
2. Check the electrical connections and connectors of the hot
water temperature sensor. Clean terminals. If the terminals are
corroded, replace the sensor and cables. Check electrical
resistance ( Fig.
3, [2]).*
3. Clean the water filter, any dirt in the taps and also the water
filters of the installation.
4. In areas where water has a high mineral content, periodic
descaling may be necessary.*
Cold water inlet temperature sensor
fault.
1. Check connector on wires coming from top of water valve for a
secure connection.
2. Sensor may trip if water temperature drops below 2 °C. Protect
heater from freezing conditions as any damage caused by freezing
conditions is not covered by the warranty.
3. Check temperature sensor for any visible damage.
Flue gas temperature sensor - the burner
will be locked if the reading gets over
90
°C.
1. Check and clean the primary heat exchanger.
2. Check and clean the condensing heat exchanger.
3. Reduce maximum output.
4. Reduce water temperature setpoint.
Burner backflow temperature sensor
over 130
°C.
The appliance will lock out the burner.
1. Check flue gas system.
2. Check if secondary fan connections are connected.
3. Check if flue requirements are met. Long flue lengths, flueing
with more than three elbows, blocked flue pipes or cross
ventilation may cause this fault.
4. Call Technical Support.
High temperature sensor (ECO) open
circuit (resets when lower temperatures
than 104
°C are detected).
1. Disconnect power supply and check wiring connections on the
overheat sensor and the two connectors on the control board.
(Fig.
2, [7]).
2. Check white wiring connections at the overheat sensor. Clean
the terminals. If badly corroded, replace sensor and wiring
harness.*
3. Check that flue requirements are met. Long flue lengths, flueing
with more than three elbows, blocked flue pipes or cross
ventilation may cause this fault.
4. Clean the water filter, any dirt in the faucets and also the water
filters in the installation.
5. In areas where water has a high mineral content, periodic
descaling may necessary.*
6. Disconnect power supply to the water heater. Open a hot water
tap for several minutes to allow cold water to pass through heat
exchanger. Close hot water tap and disconnect lead wires to
overheat sensor. Using a multimeter, check continuity through the
overheat sensor contacts. Replace sensor if continuity shows up.
Display Cause Solution
Table 28
* By qualified registered gas engineer only.
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worcester-Bosch GREENSPRING CWi47 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worcester-Bosch GREENSPRING CWi47 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info