809301
7
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
Prepare for operation
7
Worcester 2000 – 6 721 814 552 (2019/09)
3.2 Topping up the system pressure
Your installer should have informed you where to find the filling system
and instructed you in its use.
NOTICE:
System fill method
You must disconnect the external filling loop after re-pressurisation,
to comply with the Water Authority regulations.
External filling loop
Once the external filling loop and pressure gauge has been located,
follow the instructions for re-pressurising the system.
Refer to figure 3.
Unscrew the blanking cap [1].
Attach the hose [2] to the valve.
Usually one end of the hose is already connected to one of the
system fill isolation valves.
Ensure both ends [3] of the hose are screwed on hand tight.
Monitor the pressure gauge.
The system fill isolation valves [4] are in a closed position (the
handle/screwdriver slot is across the valve).
Turn the handle/screwdriver slot through 90° to open valves and
slowly fill the system.
The system fill isolation valves [5] are opened (the handle/
screwdriver slot is in-line with the valve).
The needle on the pressure gauge will start to rise.
Set the pressure between 1 and 1.5 bar pressure.
Turn the handles/screwdriver slots back, through 90°, to close the
valves.
The system fill isolation valves [6] are in a closed position (the
handle/screwdriver slot is across the valve).
Top up the system pressure, if as a result of the air bleeding the
pressure drops off.
Once the pressure has settled between 1 and 1.5 bar.
Ensure the valves are closed.
Remove the hose [2] and replace the blanking cap [1].
Fig. 3 External filling loop
If the pressure gauge reads more than 1.5 bar as a result of over filling:
Bleed one radiator until the pressure gauge returns to between 1 and
1.5 bar.
Keyless filling link
Locate the filling link (underneath the appliance on the right hand side)
and follow the instructions for re-pressurising the system.
Re-pressurise the system.
Pull the lever [1] down to start the filling process.
The needle on the pressure gauge will start to rise.
When the pressure, shown on the pressure gauge, reaches between
the 1 and 1.5 bar [2],
Release the lever [1] to stop the filling process.
Top up the system pressure, if as a result of the air bleeding the
pressure drops off.
Fig. 4
If the pressure gauge reads more than 1.5 bar as a result of over filling:
Bleed one radiator until the pressure gauge returns to between 1 and
1.5 bar.
0010015034-001
1
2
3
4
5
6
Min
1 bar
1.5 bar
Max
0010015050-001
11
Min
1 bar
1.5 bar
Max
2
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worcester-Bosch 2000 - GC2000iW C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worcester-Bosch 2000 - GC2000iW C in de taal/talen: Engels als bijlage per email.

De handleiding is 2.62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info