638065
81
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
76
77
9.2.2 Adjusting the Damping Control
The damping is adjusted by valves inside. These valves are designed to
modify the flow rate of the oil and hence the speed with which the fork legs
move in and out. In this way it is possible to optimise the bicycle’s reaction
to obstacles. Furthermore, any oscillatory movement while pedalling can be
reduced. For long uphill rides involving hard pedalling out of the saddle it is
advisable to activate the lockout mechanism. On the other hand, for down-
hill rides on uneven ground it may be better to open the damping system
more or less completely.
Suspension forks with adjustable damping are fitted with an adjusting knob
that is (mainly) red to slow down or accelerate the rebound movement (a).
The second knob, if available, is to adjust the speed of the compression
movement (b).
The adjusting process changes the flow rate of the oil contained within
the suspension fork as it passes through valves and chambers internally.
Some models provide for separate adjustment of compression and rebound
damping. Experience has shown that it is best to begin with the compres-
sion stage entirely open and to first adjust the rebound stage.
Adjusting the suspension fork is a delicate job, as even a small change on
the adjuster can have a big effect. Try approaching the exact setting you
need in increments no larger than a quarter turn from the “Open”-position.
Rebound is considered satisfactory when the suspension fork cycles once
after descending from a high kerb. If you turn the knob too far, the oil inside
will flow very slowly and the rebound will be at maximum. This will result in a
sluggish rebound movement, and the suspension fork will not recover when
exposed to a quick series of impacts.
Turning the adjusting knob in the other direction reduces rebound, making
the suspension fork rebound faster.
Once this is done, adjust the compression stage. This is to control the rate
at which the suspension fork compresses. Adjusting the compression ad-
juster towards the closed or maximum position will give you a firmer, less
active ride. Take your bicycle for a test ride on different kinds of surface (c).
If the suspension fork hits the end of its travel (bottom out) several times, you
will need to change its spring rate (d).
If the damping does not suit your needs, inspite of your adjusting, or if in the
case of coil spring elements you need more than three to four turns for the
initial spring tension, you may need to replace the suspension elements. The
replacement is a job best left to your bicycle dealer.
Do not actuate the lockout function (of the suspension fork)
when riding over rough terrain, but only when riding over
smooth terrain (roads, smooth tracks) ((a) p. 77).
a
b
c
d
Do not turn any screws on your suspension fork in the vague
hope of adjusting it somehow. You could release the fasten-
ing mechanism, thus causing an accident. All manufacturers
normally mark adjustment devices with a scale or “+” and “-“
signs (b).
Suspension fork manufacturers normally include instructions
with their deliveries. Read them carefully before changing any
settings or doing any maintenance work on your rear shock.
A too strong damping of the fork can result in a sluggish re-
bound movement with a suspension fork that will not recover
when exposed to a quick series of impacts. Risk of an acci-
dent! Do not ride your bicycle, if the suspension fork bottoms
out. This could damage the suspension fork itself as well as the
frame.
When mounting a new front tyre, make sure there is enough
clearance between tyre and fork crown as the fork compresses
entirely. The front wheel might get jammed. Risk of an accident!
9.2.3 Adjusting the Travel
The travel of some suspension fork models allow travel adjustment. Some
models reducing the travel, make for an easier uphill riding. A reduced travel
may result in a modified spring characteristic of the fork making the fork
either softer or firmer. This can reduce the comfort of suspension.
With other models, changing the travel does not result in a modified spring
characteristic. The suspension fork provides an identic comfort of suspen-
sion with an however clearly reduced travel.
Do not ride with a reduced travel over rough terrain or downhill!
For more information on adjusting the travel, please read the
enclosed instructions of the suspension fork manufacturer!
9.2.4 Maintenance
Suspension forks are components of sophisticated design that require regu-
lar maintenance and care. This has led almost all suspension fork manufac-
turers to establish service centres where you can have your fork thoroughly
checked and overhauled at regular intervals according to use, e.g. once a
year. Be sure to have all bolted connections checked at regular intervals by
your bicycle dealer.
The following routines are essential for rear shock maintenance:
Make sure the sliding surfaces of the stanchion tubes are absolutely clean.
Clean the fork with water and a soft sponge after every ride (c). After wash-
ing your bicycle, spray the stanchion tubes of the suspension fork with a little
grease spray (d) or apply a very thin film of hydraulic oil.
a
b
c
d
81

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Winora Algemene bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Winora Algemene in de taal/talen: Engels als bijlage per email.

De handleiding is 4,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Winora Algemene

Winora Algemene Gebruiksaanwijzing - Deutsch - 144 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info