638065
67
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
62
63
If you have a puncture whilst riding, do not pull the whole in-
ner tube out of the tyre. Leave the valve sticking through the
rim, inflate the inner tube and bring it close to your ear. In most
cases you can hear the air coming out. At home you can help
yourself with a bucket of water where you can locate the hole
by the bubbles. When you have found the hole, look for the cor-
responding place on the tyre and check it. Often, you will find
a foreign body sticking in the tyre, which ought to be removed.
Otherwise another puncture can occur.
When you have removed the tyre, you should also check the rim tape (a). It
should lie squarely in the trough of the rim, covering all spoke nipples, and
should not be torn anywhere or brittle. In the case of double wall rims the
tape must cover the entire rim base, but it should not be so broad as to
stand up along the inside edges of the rim trough. Rim tapes for this type of
rim should only be made of textile or durable plastic. If you are in doubt or if
you have any questions, please contact your bicycle dealer!
Replace spoilt rim tapes immediately.
If the fabric of the tyre is destroyed by the perforating object,
replace the tyre to be on the safe side.
Dismounting a Rohloff rear wheel requires special handling.
Please follow the enclosed Rohloff instructions!
7.5.3 Tyre Mounting (Clincher, Folding Tyres)
When mounting a tyre make sure no foreign matter, such as dirt or sand,
gets inside the tyre and you do not damage the inner tube in the process.
Slip one bead of the tyre onto the rim (b). Using your thumbs, press the
bead over the edge of the rim and then around the entire circumference.
This should normally be possible without using tools.
Stick the valve of the inner tube through the hole in the rim (c). Inflate the
inner tube slightly so that it becomes round and push it into the tyre all the
way round. Make sure not to leave any folds in the inner tube.
To finish mounting the tyre, start at the opposite side of the valve. Using
your thumbs, press as much of the second bead of the tyre over the edge of
the rim as you can (d). Make sure the inner tube does not get pinched and
squashed between tyre and rim. You can prevent this by pushing the inner
tube into the hollow of the tyre with a finger as you work along.
Work the tyre into the rim, approaching the valve symmetrically from both
sides. Towards the end, you will have to pull the tyre vigorously downwards
to make the already mounted portion of the tyre slip towards the deepest part
of the rim trough. This will ease the job noticeably on the last centimetres.
a
b
c
d
Before fitting the tyre completely on the rim check again whether the inner
tube lies properly inside the tyre and press the last stretch of tyre over the
edge of the rim using the balls of your thumbs (a).
If this does not work, you will have to use the tyre levers (b). Make sure the
blunt ends point towards the inner tube and the inner tube does not get
damaged.
Push the valve a little into the tyre so that the inner tube does not get caught
between the rim and the tyre beads. Check whether the valve stands up-
right. If not, dismount one bead again and reposition the inner tube. To
make sure the inner tube does not get pinched between rim and bead,
inflate the tyre a little and then move it sideways back and forth between
the sides of the rim. While doing this you can check whether the rim tape
has shifted.
Inflate the inner tube to the desired pressure. The maximum pressure is
indicated on the side of the tyre.
Check the seating of the tyre by means of the “witness line” running around
the side of the tyre just above the edge of the rim (c). The distance between
the line and the edge of the rim should be even around the entire circumfer-
ence of the tyre.
7.5.4 Removal of Tubeless Tyres (d)
Deflate the tyre completely. Press the tyre from the sides towards the centre
of the rim, until both beads lie slack in the centre of the rim. Start remov-
ing the tyre at the point opposite the valve and lift one tyre bead with your
fingers over the edge of the rim. Do not use tyre levers! Slip the entire tyre
bead over the rim. Then pull the other bead off the rim, as well.
7.5.5 Repair of Tubeless Tyres
In the event of a puncture tubeless tyres also work with an inserted inner
tube. First remove the perforating object, as far as available, from the tyre
and remove the valve from the rim. Insert a slightly inflated new inner tube
into the tyre. Mount the tyre as described below and make sure it is properly
seated in the rim and inflated to the specified pressure.
Tubeless tyres can be sealed on the inside with a conventional repair patch,
as well. Observe the instructions of the repair kit manufacturer.
Improper mounting can lead to malfunctioning or even result in
tyre failure. Therefore, be sure to follow the instructions of the
manufacturer enclosed with the delivery.
a
b
c
d
67

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Winora Algemene bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Winora Algemene in de taal/talen: Engels als bijlage per email.

De handleiding is 4,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Winora Algemene

Winora Algemene Gebruiksaanwijzing - Deutsch - 144 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info