638065
44
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
40
41
Check the pads for wear by inspecting the thickness of the braking material
attached to the backing plate within the brake calliper (a) or view through the
window on the upper side of the calliper (b). If there is approximately 1mm of
material left on each brake pad, remove the pads according to the manufac-
turer’s instructions, check them thoroughly and replace them, if necessary.
Dirty brake pads and rotors can lead to drastically reduced
braking power. Therefore, make sure the brake remains free of
oil and other fluids, especially when you clean your bicycle or
grease the chain. Dirty brake pads can under no circumstances
be cleaned, they must be replaced! Rotors can be cleaned with
warm water and mild soap. There are also special brake clean-
ers available.
Loose connections and leaky brake lines drastically impair brak-
ing power. If you find leaks in the brake system or buckled lines,
contact your bicycle dealer immediately.
The manufacturers of hydraulic disc brakes usually deliver their
products with detailed instructions. Be sure to read them care-
fully before removing a wheel or doing any maintenance work.
5.3.2 Checking and Readjusting Mechanical
Disc Brakes
Regularly check whether you get a positive braking response before the
lever touches the handlebars.
Make sure the brake cables are in sound condition!
To a certain extent, wear of the brake pads can be compensated directly at
the hand lever. Unscrew the union nut on the bolt through which the cable
enters the lever and then unscrew the bolt until the lever has the desired
travel (c). Retighten the lock nut by taking care that the slot of the bolt does
not face upward or forward, as this would permit an unnecessarily high
amount of water or dirt to enter (d).
Now check the functioning of the brake and see to it that the brake pads
do not drag on the rotor ((a) p. 41) when you release the brake lever and let
the wheel spin.
Repeated readjustment at the brake lever makes the arm on the brake cal-
liper change its position. This can reduce braking power and result in a
complete brake failure in an extreme case!
Some systems must be readjusted directly at the brake calliper
to compensate wear. For more information please read the en-
closed manual of the brake manufacturer.
a
b
c
d
Some models offer further ways of adjusting the brakes directly at the brake
calliper, though this requires a certain amount of skill. In any case, be sure
to read the original instructions of the brake manufacturer before adjusting
the brakes. If you are in doubt or if you have any questions, please contact
your bicycle dealer!
Damaged cables (b) should be replaced immediately, as they
can snap.
Repeated readjustment at the brake lever can drastically reduce
the maximum braking performance.
The manufacturers of mechanical disc brakes usually deliver
their products with detailed instructions. Be sure to read them
carefully before removing a wheel or doing any maintenance
work.
If your brake system works with DOT brake fluid, the latter needs
to be replaced regularly according to the intervals prescribed by
the manufacturer.
a
b
44

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Winora Algemene bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Winora Algemene in de taal/talen: Engels als bijlage per email.

De handleiding is 4,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Winora Algemene

Winora Algemene Gebruiksaanwijzing - Deutsch - 144 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info