315150
12
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
29
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (depending on model) point to the source of the fault.
Fault description table.
a.
*
Water inlet fault (no or insufficient water
supply)
Switch off the washing machine by pressing the
“On/Off”
button and unplug it.
Check whether:
the water tap is fully turned on, and the water
supply pressure is sufficient.
the water inlet hose is kinked.
the mesh filter in the water inlet hose is blocked
(see “Care and maintenance”).
the water in the water inlet hose is frozen.
the washing machine has a safety hose and the
safety valve is open (red indicator in the safety
valve inspection window). In this case replace it
with a new safety hose.
Reconnect the washing machine.
Press the
“On/Off”
button to continue with the
programme (do not add detergent for this
programme).
If the fault re-occurs, contact After-Sales (see
“After-Sales Service”).
b.
*
Draining out fault
Switch off the washing machine by pressing the
“On/Off”
button and unplug it.
Check whether:
the drain hose is kinked (see “Installation”).
the pump impeller is obstructed (see “Cleaning
the foreign body trap”).
the water in the drain hose is frozen.
If water has remained in the drum, you can drain
it by following the instructions in the chapter
“Draining residual water”.
IMPORTANT:
Before draining, allow the wash
water to cool down.
Reconnect the washing machine.
Press the
“On/Off”
button to continue with the
programme (do not add detergent for this
programme).
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”).
c.
*
Electrical module fault
Switch the washing machine off. Switch the
washing machine on by pressing the
“On/Off”
button twice.
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”).
d.
*
Water stop fault
(depending on model)
In addition to the fault indicators the pump operates.
The “Water Stop“ fault may have been triggered by:
1.
Too much foam.
2.
A leak in the inlet hose or in the washing
machine.
Switch the washing machine off by pressing the
“On/Off“
button, unplug the washing machine
and turn off the water tap.
Tilt the washing machine forwards carefully to
allow the water to evacuate from the bottom tray.
Then:
1.
Reconnect the washing machine.
2.
Turn on water supply (if
“On/Off“
button is not
pressed, but the machine begins to fill, turn off
the water supply tap and contact After-Sales
Service).
3.
Press the
“On/Off”
button. Reselect the desired
programme, add detergent, if necessary, and
press the
“Start“
button to restart the
programme.
If the fault occurs again, contact After-Sales
Service (see “After-Sales Service“).
The pilot lamp of the “Start” button and the
following spin speed indicator lamps are
flashing
Fault description
1st (“0”) “Water inlet fault”
1st (“0”) + 2nd “Draining fault”
Other combinations Electrical components fault”
1st (“0”) + 4th Water Stop fault
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Whirlpool awa 6095 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Whirlpool awa 6095 1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info