574738

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
5019 300 01458
Whirlpool is a registered trademark of Whirlpool USA
Load the laundry, close the door and turn the programme selector to
the desired programme; the
“Start/Pause”
indicator blinks.
The
temperature
and
spin speed
shown on the display can be
altered by pressing the “Temperature” key or the “Spin” key
. If you do not use the “Dosing Aid” , add detergent now.
If the combination programme/option or option/option is not
possible, the indicator switches off automatically and a signal
sounds. To activate options around the display, just press the key
until the relevant symbol on the display lights up.
“Colours 15°” button
Saves energy used for water heating while maintaining a good wash
result.
Supports colour maintenance when washing coloured laundry.
Recommendable for lightly soiled laundry without stains.
Make sure that your detergent is suitable for cold wash
temperatures (15 or 20 °C).
Not selectable for Cotton 70 - 95°C.
“Rapid” button
Enables quicker washing by shortening the programme duration.
Recommendable for only lightly soiled laundry.
Not selectable for Cotton 70 - 95°C.
“Prewash” key
Adds a prewash cycle to the wash programme selected; prolongs
the programme by about a quarter of an hour.
Recommended for heavily soiled laundry (e.g. containing sand or
granular dirt).
“Intensive rinse” key
More water is added and rinse cycle is prolonged.
Particularly suitable for areas with very soft water or for washing
baby linen, and helps people with allergies.
“Soil level” key
Adapts the programme duration to the soil level of your laundry
(small = lightly, medium = normally, big = heavily soiled). Also
influences the detergent quantity recommendation when using the
“Dosing Aid” button.
Not all soil levels are selectable for each programme.
“Spin” key (incl. “Rinse Hold” )
Press the key to change the predefined spin speed. If you select spin
speed “0”, the final spinning is cancelled and the water is drained out
only. However, intermediate spin phases remain during the rinse.
If you select “Rinse hold” , the laundry remains in the last rinse
water without progressing to the final spin cycle, to avoid creasing
and prevent colours from changing. To activate the “Rinse hold”,
press the “Spin” key repeatedly until the “Rinse hold” symbol
on the display lights up.
- The programme stops to “Rinse hold” when
on the display
blinks; the
“Start/Pause”
indicator blinks as well.
- To terminate the “Rinse hold” by spinning the laundry, press
“Start/Pause”
- the laundry will be spun with the default spin
speed. You can also select another spin speed with the “Spin”
button before you start the spin cycle with
“Start/Pause”
.
- To terminate the “Rinse hold” by draining the water without
spinning, press the “Spin” button until spin speed “0” appears on
the display; then press
“Start/Pause”
to start the draining.
- Do not leave the laundry to soak for too long in the “Rinse hold”
(especially silk!).
You can postpone your programme to complete at a later time:
press the key to select in how many hours the programme shall be
finished. Thus, it allows you to have your laundry ready at a particular
time and to profit from more favourable energy rates during the
night, for example.
• The time until the “Cycle end” can be selected in full hour time
segments (1 to 24 h). When you press the key, the shortest
possible time will be displayed; keep on pressing the key to loop
through all the available times. To remove it again, keep on
pressing the key until you see the value “0:00”.
• When you have selected the desired time until the “Cycle end”,
press
“Start/Pause”
- the countdown will begin.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration (hours : minutes)
without “Rapid” with “Rapid”
Mixed 40 6.0 65 0.65 1:00 —
Cotton 95 9.0 90** 2.60 2:40 —
Cotton 60 9.0 60 1.60 2:20 1:45
Cotton 40 9.0 60 0.85 2:05 1:15
Synthetics 60 3.5 48** 0.95 1:37 1:12
Synthetics 40 3.5 45 0.55 1:20 0:55
Delicates 40 2.5 70 0.70 0:50 —
Wool/Handwash 40 2.0 45 0.60 0:40 —
White 40 9.0 85 0.85 2:20 —
Light colours 40 6.0 70 0.50 1:20 —
Dark 40 6.0 49 0.60 1:40 1:15
Cotton *
60 9.0 51 0.94 4:00 —
Cotton *
60 4.5 34 0.80 3:45*** —
Cotton *
40 4.5 34 0.77 3:45*** —
AquaEco 40 3.0 19 0.45 1:00 —
Speed 15 30 3.0 30 0.20 0:15 —
Big Items 40 3.0 70 0.75 1:30 —
Bedlinen 60 3.5 60 1.30 2:00 —
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water
supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature.
Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options
or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.
*** Automatic adaptation of programme duration after detection of wash load.
* Reference programmes for Energy Label.
LOAD LAUNDRY AND SELECT PROGRAMME
SELECT ANY DESIRED OPTION
SET CYCLE END
• During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.). If the
modifications prolong the programme duration so that it
overruns the originally set time until the “Cycle end”, the
programme will start immediately.
• Sometimes the programme may finish before the selected time
until the “Cycle end” has expired (e.g. for small loads). In this case,
the washing machine will tumble the laundry regularly to keep it
fresh, until the selected “Cycle end” time has expired. During
tumbling, the display will show an animation. The tumbling
phase can be stopped at any time either by pressing any button
or by rotating the programme selector; the animation will stop
and the door will unlock in about 1 minute as indicated on the
display.
With the “Dosing Aid”, you can make your washing machine indicate
you the recommended detergent quantity for your wash load,
depending on the soil level selected and the size of the load.
• Helps to save detergent and protect the environment and also
sensitive skin by avoiding detergent overdosing.
• Before you use this function, you must adapt the washing
machine to the dosing amounts which are recommended for the
detergents you use. Also check if your region’s water hardness
corresponds with the water hardness level “soft” of your washing
machine - if not adapt it.
• Select programme and options and set cycle end before
activating the “Dosing Aid”.
For any details, refer to the separate “Dosing Aid” Instructions for Use.
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pressing the
“Favourites”
key .
• Select the desired programme, temperature, spin speed and
option(s), press and hold the
“Favourites”
key for at least 3
seconds. The heart symbol on the display shortly blinks and
then lights up - the programme setting is saved.
Next time you want to use your individual programme setting, select
the programme,
shortly
press the
“Favourites”
key and start by
pressing
“Start (Pause)”
.
If you want to replace the saved programme setting by another one:
• Proceed as already described above - the previously saved
programme setting will be replaced by the new one.
Before starting a programme, the indicator lights to show that the
door can be opened. As long as a wash programme is running, the
door remains locked and must on no account be forced open. In case
you have an urgent need to open it during a running programme,
refer to “Reset a running programme before the end”.
The “Eco monitor” gives you a rough feedback about the power
consumption of the programme setting you selected.
As soon as you turn the programme selector to any programme, the
“Eco monitor” is on.
The indicator on the left is to show that the “Eco monitor” is active.
The four indicators next to it show the degree of consumption: the
less power your programme setting is forecasted to consume, the
less indicators will light up. This depends on the programme,
temperature and options selected, and also on the size of the wash
load. For that reason, the forecasted degree of power consumption
may adapt when the washing machine detects the wash load.
When you select a programme, the drum light will slowly go on to
assure a good visibility during laundry loading.
After starting your programme with
“Start/Pause”
, the drum light
will fade on and off while the washing machine detects the laundry
load. Subsequently, it will go off.
When the programme is finished, the light goes on again for a short
time; afterwards it will go off automatically to save energy. If you
want to switch it on again for unloading your laundry, just press any
option button or turn the programme selector (but not to “Off/O”).
The drum light will blink fast when a failure is detected.
Open the tap and press the
“Start/Pause”
button . The
“Start/
Pause”
indicator lights up. The display shows the remaining
programme time. During detection of the laundry load and new
calculation of the programme time, an animation appears on the
display.
Prevents children from starting a wash cycle or changing the
settings of a running programme. Cannot be activated or
deactivated when the programme selector is in the “Off/O” position.
To activate the child lock:
• Turn the programme selector to a programme position, or run a
programme as usual.
• Press and hold the 2 buttons marked with the key symbol
simultaneously for a few seconds. A key symbol will appear on
the display to indicate that the child lock is active.
Any time you try to change a programme setting with active child lock, a
signal will sound; it cannot be changed anymore. The only change
possible is to switch the washer off by turning the programme selector to
the “Off/O” position. To deactivate the child lock, proceed in the same way
as for activating it (signal will sound twice).
Press and hold the marked buttons simultaneously for a few seconds
to switch off the peep sound of the buttons and at the end of the
programme; a long signal sounds. To switch it on again, proceed in
the same way; a short signal sounds twice.
If one of the failure indicators lights up, or in case of any malfunction,
consult the “Troubleshooting Guide” in your Instructions for Use.
Spin speed on display blinks:
Unbalance during spinning.
• The “Programme finished” indicator lights up. The display
shows “End”.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
The symbol will light up at the end of the programme if you used too
much detergent. Use less detergent next time.
1. Press the
“Start/Pause”
button to pause the programme.
The indicator blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the
“Start/Pause”
button again. The new programme
continues at the same position where the previous programme
was interrupted. Do not add detergent for this programme.
The
“Reset/Drain”
button cancels a programme before the
end.
•Press and hold the
“Reset/Drain”
button for a few
seconds; an animation appears on the display. The water is
drained out; it may last some time until you can open the door.
DETERGENT DOSING RECOMMENDATION
SAVE YOUR FAVOURITE PROGRAMMES
“DOOR OPEN” INDICATOR
ECO MONITOR
DRUM LIGHT
PROGRAMME START
CHILD LOCK
SOUND OFF
FAILURE INDICATORS
PROGRAMME END
DETERGENT OVERDOSAGE INDICATOR
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE THE
END
- the sensor technology adapts water, energy and programme duration to the size of your wash load
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Whirlpool-Pure-90140---6TH-SENSE-InfiniteCare-1400

Zoeken resetten

6
12
18

  • Ik heb whirlpool wasmachine 6sense
    1400 en 6kg heb hem schoongemaakt met hg onderhoudmonteur nu als hij op spoelen gaat stopt hij ermee en brand service lampje wat nu help. Gesteld op 8-4-2020 om 23:50

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Gebruiksaanwijzing - Nederlands - 11 pagina's

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Snelstart handleiding - Nederlands - 2 pagina's

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Gebruiksaanwijzing - Deutsch - 11 pagina's

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Snelstart handleiding - Deutsch - 2 pagina's

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Gebruiksaanwijzing - English - 12 pagina's

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Gebruiksaanwijzing - Français - 11 pagina's

Whirlpool Pure 90140 - 6TH SENSE InfiniteCare 1400 Snelstart handleiding - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info