Handleiding Whirlpool AWE 6720 (pagina 2 van 2) (Engels)

607062

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

5019 312 10610

1. Load the machine, close the drum doors and check

that they are properly locked.

2. Add detergent and additives into the dispenser to

no more than the “MAX” level mark, as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Stain remover agents

• Anti-scale agents (if necessary)

3. Close the lid.

4. Turn the programme selector to the desired

programme and temperature. The lamp next to the

“Start/Pause” button flashes. The indication lamp

of the predefined spin speed lights up.

CONSUMPTION DATA

Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in

compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to

the water supply pressure and temperature, the load and the type of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water

out.

** Reference Programme for Energy Label.

PREPARATION OF THE WASH CYCLE

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a

wash programme is running, the lid remains locked and

must on no account be forced open. In case you have

an urgent need to open it during a running programme,

refer to “Cancel (Reset) a running programme before

the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

“Intensive rinse” button

• The amount of water is increased to ensure a more

intensive rinse.

• This option is particularly suitable for areas with very

soft water, washing baby linen and people with skin

allergies.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• This option is particularly recommended for the

“Synthetics”, “Daily load” and “Delicates”

programmes.

• It is useful if you want to postpone spinning to a later

time, or if you want to drain out only.

• If you select “Rinse Hold”, do not leave items to

soak for too long.

• As soon as the appliance stops in the rinse hold, the

“Anticrease” lamp of the sequence indicator lights up

and the lamp next to the “Start/Pause” button

flashes.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme

will terminate automatically with the final spin cycle

for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the “Start/Pause” button.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

the rinse. The water is drained out only.

Whirlpool is a registered trademark of Whirlpool USA.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows

the current programme phase, running from left to right

through Wash, Rinse, Spin/Drain. When the programme

phrase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open for some time to allow the

interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme, any options and another

spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the

end. Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the lid can be

opened.

SELECT THE DESIRED OPTION(S)

Selecting or deselecting an option can be done at

any time during the programme. The option will be

applied as long as the corresponding programme

phase has not been executed yet.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time by

approximately 20 min.

“Eco” button

• With a modified temperature profile and a slightly

prologned washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

START DELAY

The “Start delay” allows to the user to run the machine

at his convenience, for example at night when electricity

is cheaper.

• Select programme, spin speed and options.

• Press the “Start Delay” button several times to

select a delay time of 1, 3, 6, 9 or 12 hours.

The corresponding indicator lamp lights up.

• Start the programme (see “Progremme Start”).

The indication next to the “Start delay” button lights

up and goes off when the programme starts.

• Once having pressed the “Start/Pause” button,

the countdown of the time delay begins. When the

programme starts, the start delay indicator light

goes off and is replaced by the programme sequence

indication.

• After the “Start/Pause” button has been pressed,

the number of hours preselected can be reduced by

pressing again the “Start delay” button.

To cancel the “Start delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another position

or press the “Reset” button.

..after having pressed the “Start/Pause” button:

• Press the “Reset” button for at least 3 second. The

start delay indicator light goes off.

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration***

(hours : minutes)

White Cotton 95 5.5 55* 1.70 1:55

Cotton 60 5.5 49 1.02 2:25

Cotton + Eco** 60 5.5 49 0.93 2:35

Cotton 40 5.5 53 0.55 2:00

Jeans 40 5.5 73 0.55 2:15

Synthetics 60 2.5 53* 0.85 1:30

Synthetics 40 2.5 47 0.50 1:15

Delicates 40 1.5 51 0.50 0:45

Daily load 40 3.0 43 0.48 1:00

Quick wash 30 3.0 36 0.30 0:30

Wool 40 1.0 53 0.50 0:45

Handwash 40 1.0 43 0.50 0:35

Handwash 30 1.0 42 0.30 0:35

Whirlpool AWE 6720 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Whirlpool AWE 6720

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info