Handleiding Whirlpool AWE 6517 (pagina 2 van 2) (Engels)

586256

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

5019 300 00388

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 5.0 50* 1.70 2:05

Cotton** 60 5.0 47 0.89 2:45

Cotton** 60 2.5 32 0.68 2:10

Cotton 40 5.0 47 0.65 2:00

Cotton** 40 2.5 32 0.52 1:45

Synthetics 60 2.5 50* 0.80 1:30

Synthetics 40 2.5 45 0.45 1:15

Delicates 40 1.5 50 0.55 0:45

Daily load 40 3.0 40 0.45 1:00

Quick wash 30 3.0 35 0.40 0:30

Wool 40 1.0 55 0.55 0:45

Handwash 40 1.0 40 0.40 0:35

Handwash 40 1.0 40 0.30 0:31

1. Load the machine, close the drum doors and check

that they are properly locked.

2. Add detergent and eventual additives as described on

the front page and in your Instructions for use.

3. Close the lid.

4. Turn the programme selector to the desired

programme and temperature. The lamp next to the

“Start/Pause” button flashes. The indication lamp

of the predefined spin speed lights up. If you do

not start the programe soon after having made your

choice, the washing machine will switch off

automatically after about a quarter of an hour. Switch

on the washing machine again by turning the

programe selector back to „Off/O“ and then to the

desired programe.

CONSUMPTION DATA

PREPARATION OF THE WASH CYCLE

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a

wash programme is running, the lid remains locked and

must on no account be forced open. In case you have

an urgent need to open it during a running programme,

refer to “Cancel (Reset) a running programme before

the end”.

“Intensive rinse” button

• Theamountofwaterisincreasedtoensureamore

intensive rinse.

• Thisoptionisparticularlysuitableforareaswithvery

soft water, washing baby linen and people with skin

allergies.

“Rinse Hold” button

• Thelaundryremainsinthelastrinsewaterwithout

progressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• Thisoptionisparticularlyrecommendedforthe

“Synthetics”, “Daily load” and “Delicates”

programmes.

• Itisusefulifyouwanttopostponespinningtoalater

time, or if you want to drain out only.

• Ifyouselect“RinseHold”,donotleaveitemsto

soak for too long.

• Assoon as the appliance stops in the rinse hold, the

“Rinse hold” lamp of the sequence indicator lights up

and the lamp next to the “Start/Pause” button flashes.

Terminate the “Rinse Hold” option:

• Pressthe“Start/Pause” button; the programme

will terminate automatically with the final spin cycle

for the present wash programme.

• Ifyoudonotwishtospintheclothes,turnthe

programme selector knob to the “Drain”

programme and press the “Start/Pause” button.

Whirlpool is a registered trademark of Whirlpool USA.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows

the current programme phase, running from left to right

through Wash, Rinse, Spin/Drain. When the programme

phrase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

PROGRAMME END

• The “Door open” indicator lights up. After about a

quarter of an hour, the washing machine will switch

off completely to save energy.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open for some time to allow the

interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme, any options and another

spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the

end. Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the door can be

opened.

SELECT THE DESIRED OPTION(S)

Selecting or deselecting an option can be done at

any time during the programme. The option will be

applied as long as the corresponding programme

phase has not been executed yet.

“Prewash” button

• Onlyforheavilysoiledloads(forexamplesand,

granular dirt) sensible. Increases the cycle time by

approximately 20 min.

“Half load” button

• Reduceswaterconsumption,aboveallduringrinsing.

• Suitableforlightlysoiledlaundryandsmallloads

(max. 3 kg).

“Variable spin” button

• Everyprogrammehasapredefinedspinspeed.

• Pressthebuttontosetanotherspinspeed.

• Ifspinspeed“0”isselected,thefinalspinningis

cancelled but intermediate spin peaks remain during

the rinse. The water is drained out only.

FAILURE INDICATIONS

In a case of any failures of irregularities, consult the

“Troubelshooting Guide” in Instruction for Use.

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the

home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type

of wash. Water and energy consumption refer to the default setting of the programmes; selecting special options or modifying spin

speed or temperature will change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that

time (see also “Troubleshooting Guide” in your Instructions for Use).

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared

cycle temperature.

Power consumption in off-mode 0.11 W / in left-on mode 0.11 W.

Whirlpool AWE 6517 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Whirlpool AWE 6517

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info