539859
1
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
GB -1-
Chart
(see at right for options description)
PROGRAM SELECTION
BUTTON
Push “P” button (repeatedly)
until selected program number
is shown on the display
(P1...Px) - see “Table of
programs” below.
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the program.
When the door is opened during a washing cycle, the
cycle is temporarily paused: the Start indicator blinks.
To resume the cycle push Start button and close
the door within 3 seconds.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute (0:01
is shown into the display). If pressed when the
dishwasher is switched off, it drains any possible
liquids from dishwasher (1 minute process).
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions.
Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test
and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
RECYCLING WATER SYSTEM: these programs save water in a dedicated tank.
A TANK CLEANING CYCLE (at least 45 min.) is automatically run every 30 cycles or after every power off, to assure the best product conditions.
Table of programs
Deter-
gent
Consumption
Drying
Phase
Programs
Available
options
Loading instructions
Litres kWh
Minutes
1)
P1
6th Sense
Power Clean
40°-70°C
Delay
Multizone
Power Clean
Use for normal soiled dishes with dried-on food.
Senses the level of soiling on the dishes and adjusts the
program accordingly. When the sensor is detecting
the soil level an animation appears in the display and
the cycle duration is updated. The Power Clean
option is activated automatically with this program. To
deactivate, press the Power Clean button on the
control panel.
X 7-14 1.00-1.65 80-165 Full
P2
Pre-Wash cold
Delay
Multizone
Crockery to be washed later. 4.0 0.03 14 NO
P3
Fragile 40°C
Delay
Multizone
Light soiling, for example glasses and cups. X 10.0 0.85 100 Light
P4
Rapid 45°C
Delay
Multizone
Lightly soiled crockery, with no dried-on food. X 11.0 0.80 30 NO
P5
Eco
2)
50°C
Delay
Multizone
Power Clean
Normally soiled crockery.
Energy-saving program.
X 7.0 0.92 245 Full
P6
Fast Daily 60°C
Delay
Multizone
Normally soiled crockery. X 10.0 1.30 80 Full
P7
Silent 50°C
Delay
Multizone
Normally soiled crockery, gentle and quiet thanks to
the lower spray pressure (39 dbA).
X 10.0 1.20 290 Light
P8
Intensive 65°C
Delay
Multizone
Power Clean
Recommended program for heavily soiled crockery,
especially suitable for pans and saucepans.
X 11.0 1.60 145 Full
P9
Steam
Delay
Multizone
Power Clean
Program including steam action dedicated for heavily
soiled crockery, pots and pans. Soaking or hand
pretreatment is no longer needed.
X 10.0 1.70 180 Full
P10
Hygiene
3)
Delay
Multizone
Power Clean
Normally or heavily soiled crockery, with additional
antibacterial wash. Program interruption (e.g. due to
door opening) can compromise elimination of germs.
X 13.0 1.50 118 Full
5019 396 03771
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS
QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
Options and display description
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE
CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER
30 SECONDS IF NO CYCLE HAS STARTED.
MULTIZONE
Allows you to choose the washing
zones. Press this button (repeatedly)
to select the wash zones:
both racks
only lower rack
only upper rack
- indicator lits
TABLET SETTING
This setting allows to
optimize the cycle
performances according
the type of detergent
used. Push the Tablet
button for 3 seconds (until
the indicator lights up)
if you are using the
combined detergents in
tablet (rinse aid, salt and
detergent in 1 dose).
If you are using powder
detergent or liquid
detergent, the Tablet
indicator on the control
panel has to be off.
DELAYED START
BUTTON
Push the button
(repeatedly) to delay the
start of the program.
Adjustable from 1 to 24
hours. With each press of
the button, the delayed
start indicator increases
by one hour and after
24 restarts from 0. Then
press the START button.
The dishwasher will start
after the set time.
POWER CLEAN
Thanks to the additional power jets
this option provides a more intensive
and powerful wash in the lower rack,
in the specific area. This option is
recommended for washing pots and
casseroles (see page 4). Press this
button to activate Power Clean (the
indicator lights up).
For non Power Clean loading to
achieve best cleaning performances
and resources optimization, Power
Clean should be switched off.
SALT INDICATOR
When lit (at the end of the cycle), the
salt reservoir needs to be refilled.
RINSE AID INDICATOR
When lit (at the end of the cycle), the
rinse aid dispenser needs to be refilled.
OPERATION
INDICATOR
A LED light
projected on the
floor indicates that
the dishwasher is
working.
Quick reference guide
Whirlpool is a registered trademark of Whirlpool USA
GB -2-
First time use
1
4
10
9
23
5
7
86
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5, 6, 7, 8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set only
before the first wash or if water
hardness has been changed
1
Visual indicator
(depending on
the model).
Unscrew cap.
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
green: OK.
clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next
press of the start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
At first time use, the salt
reservoir has to be filled
independently from water
hardness level (see
description below in step 1
“Daily check”).
1. Ask your water supply company what the water hardness is... 2. ...enter this value on
your dishwasher
Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness level
Insert value is shown in the
display
Gel or Powder (rinse
aid and salt)
Tablets
0 - 5 0 - 9 0 - 6.3 Soft 1
go to step 1 (see
“Daily check”)
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
if water is HARD
extra salt needs to
be added (go to
step 1, “Daily
check”)
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
Water hardness level is factory
set for medium-hard water
(level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration salt
since such detergents are not
effective enough at softening
hard water.
Once regeneration salt is added, immediately start a wash program (the “Pre-wash program alone is not sufficient). Residual saline solution or grains of salt can lead to
deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.
Fill the salt reservoir with water
before the first wash only.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
How to set water hardness in order to always assure the best cleaning results
GB -3-
Daily check
3
Check the rinse aid indicator to check the level
into the dispenser.
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when RINSE AID NEEDS
TO BE ADDED.
dark: OK. clear: NEEDS TO BE ADDED
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the
appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty
drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with
rinse aid incorporated tend to form excess suds.
Daily use
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A (press the
dedicated button).
Only fill the
detergent dispenser
prior to starting a
wash program.
Shut the cover by pressing
dedicated ribs.
If required,
open the
cover B
(press the
dedicated
button).
Add rinse aid
to the max.
line ~150 ml
The rinse aid dosage can be
adjusted to the detergent used.
The lower the setting, the less
rinse aid is dispensed (factory
setting: position 4).
Press the button to open the
cover B. Using a coin or similar
object, turn the arrow to the
desired setting. After adjusting
the rinse aid setting, shut the
cover again.
Visual
indicator
2
Insert detergent: Tablet / powder / liquid into the big chamber.
Please look for the recommendation of the detergent manufacturer on
the packaging of the detergent product.
Use only one tablet per one cycle, only
placed in detergent dispenser.
All types of tablets can be used, but for
2 in 1 type adding of salt is mandatory.
Some types of tablets may not dissolve
completely during the short cycles
(Rapid, Fragile, Handwash); placing the
tablet on the tub bottom can help
dissolving and washing.
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Whirlpool ADG 8558 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Whirlpool ADG 8558 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Whirlpool ADG 8558

Whirlpool ADG 8558 Snelstart handleiding - Nederlands - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info