579833
13
Verklein
Vergroot
Pagina terug
1/61
Pagina verder
5. Setting up the device
WARNING!
Electric shock and risk of burns
Connecting the control unit incorrectly poses a risk of
injury and damage to the device. Risk of burns from the
soldering tool while the control unit is operating.
5Read the enclosed instructions, the safety instructions
included in these operating instructions as well as
the instructions for your control unit all the way through
and observe the specified precautionary measures
before operating the control unit.
5Always place the soldering tool in the safety rest
when not in use.
5Disconnector is not for mains disconnection!
5Switch off disconnector when not in use
("0" position).
1. Carefully unpack the device.
2. When fitting the new soldering tip, make sure that
the soldering tip is inserted all the way up to the stop
in a single smooth action. Operating
the soldering iron with a soldering tip that is not fully
inserted can cause malfunctions.
Important:
Always ensure that the soldering tip is seated properly.
3. Place the soldering tool in the safety rest.
4. Check whether the mains supply voltage matches the
specification indicated on the rating plate and whether
the disconnecting switch (6) is off, battery version only.
5. Connect the control unit to the mains power using the
power pack (26). Set the disconnecting switch (6) to
"I" to charge the battery. The display (1) shows "OFF".
6. BAT (10) is flashing to indicate charging process.
7. Press the + (2) and (3) buttons for approx. 1 sec to
switch "ON" the device, "ON" appears on the display (1).
The electronics automatically switch to the actual value
display.
6. Operation
6.1 Setting the temperature
Setting the temperature individually
1. Press the + or - button.
The display switches to the setpoint value. The temperature
symbol (8) flashes.
2. Press the + or - button to set the required setpoint
temperature
- Touching the button briefly alters the setpoint value
by one degree Celsius / Fahrenheit
- Pressing the button permanently alters the setpoint
value in rapid pass mode.
The actual value appears on the display again approx. 2
seconds after the buttons are released.
6.2 Soldering
Handling soldering tips
- Coat the tin-plated soldering tip with solder when
heating the iron for the first time to remove any oxide
films or impurities from the soldering tip that have
accumulated during storage.
- During pauses between soldering and before storing
the soldering iron, ensure that the soldering tip is
wellcoated.
- Do not use aggressive fluxing agents.
- Always ensure that the soldering tip is seated properly.
- Select the lowest possible working temperature.
- Select the largest possible soldering tip shape for the
application.
Rule of thumb: approx. as large as the component
or mounting surface on the printed circuit board
- Coat the soldering tip well to ensure efficient heat
transfer between the soldering tip and soldering point.
- Switch off the system if you do not intend to use the
soldering iron for longer periods or activate the
Weller temperature reduction function.
- Coat the tip before placing the soldering iron in the
safety rest.
- Apply the solder directly at the soldering point, not on
the soldering tip.
- Do not subject the soldering tip to physical force.
9
English
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Weller WSM 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Weller WSM 1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info