50963
11
Verklein
Vergroot
Pagina terug
1/53
Pagina verder
3.2 TARE
Function : Digital zero setting of the gross weight value with 0.1 scale division
accuracy. Allowed within the complete weighing range.
Taring : With tare command: X ! N CR (= set net), or built in into a setpoint
executive code. See table 7, 2
e
column on page 45.
If a tare is in operation, i.e. the weight reading is net, the gross weight value
always may be requested with: X ? G CR , the tare will not be deleted.
A tare is cancelled with command: X ! G CR (set gross)
3.3 DAMPING / FILTERS
Standard filter : Digital two pole filter from 0.13 Hz up to 4.02 Hz in 8 steps. Setting by
dil-switches 49 . . 52 on the main print board, see table 2 on page 40.
Adaptive filter : This progressive filter damps down the weight movements automatically with
more force as the weight movement tends to decrease.
This results in a major improvement of the time necessary for achieving a
“standstill” and prevents for blinking up and down of the weight reading.
The increased filtering of the adaptive filter is switched off immediately
if more than ½ scale division change in the weight value is measured longer
than ½ second. Pulsating changes however are neglected by integrating
calculation of the weight values.
The adaptive filter is default “on”, but may be disabled with command : ! E 3
(off), and reset with : ! E 2 (on).
Anti pulse filter : Effective only for the weight values sent to the setpoint comparator.
Pulsating weight changes are recalculated, based upon the steepness of the
pulse and the remaining increase of weight after a pulse. In this way the
kinetic energy of the pulse will be levelled, resulting in a correct weight value
that is used by the setpoint comparator.
Short “overshoots” of the measured weight value is strongly prevented by this
filteren, premature switching off of the setpoints is prevented.
The anti pulse filter is switched on with the start command code of the
setpoints, see table 8, last column on page 46.
Inflight filter : Effective only for the weight values sent to the setpoint comparator. This filter
measures continuously (426 x per second) the speed of the weight increase.
From the derivatives of these range of measured values, it calculates the
kinetic energy, pushing on the scale. The weight value of this energy is added
to the actual value, causing a premature cut off of the setpoints.
In this way course filling may last longer, and fine dosing time will be shorter,
since overshoot risk is strongly limited, it will speed up the capacity of filling.
The anti pulse filter system is incorporated in the inflight filter.
Since these filters are measuring continuously at high speed, a change in
weigh speed immediately will result in correction of the setpoint cut off values.
The inflight filter is switched on with the start command code of the
setpoints, see table 8, last column on page 46.
.
Manual 348-2 V 3.1 Page 11 01-06-2007
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Weightec 348 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Weightec 348 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Weightec 348

Weightec 348 Gebruiksaanwijzing - Nederlands - 49 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info