50963
6
Verklein
Vergroot
Pagina terug
1/53
Pagina verder
1.5 MEASURING PRINCIPLE
The A/D converter proceeds according to the unique continuous integrating principle and converts at 436 Hz
the analogue weight signal into a 21 bits digital value.
The 348 has 5 different types of filters for stabilizing the weight data. Amongst these 3 filters especial for the
setpoint comparison with automatic overshoot compensation and one manual settable filter.
The 3 filters for the setpoint comparison are selected in the start command for the setpoints.
The complete A/D conversion, as well as the analogue amplifier system, operates at 218 Hz (sine wave) speed.
The loadcell excitation and the sense return system operate at the same frequency and sine wave.
The measuring system is based upon synchronic detection of the AC signal and continuous integrating ratio
measurement by the A/D converter.
The big advantages of using alternating current with sine wave are the highly insensitivity for disturbances from
external interferences, a very stable zero without any drift and the feature that the loadcell connections may be
made with screw terminals in stead of soldered connections.
1.6 ACCURACY / SPEED
The internal resolution is 2,000,000 counts (21 bit) with a instability (noise)of max 3 count.
The EC legal approval allows for a minimum signal of 0.3 µV per scale division at 5.6 V loadcell excitation.
For a 2 mV/V loadcell this more than 37,000 counts / divisions, resulting in an accuracy of 0.003% of the
measuring range of the loadcell.
The EC Metrology Legislation for Class III weighing instruments limits this value to a maximum of 10,000 counts.
On the internal calibration display the digital weight signal is presented in max. 150,000 divisions.
In the data output max. 15,000 scale divisions available.
The high speed of the complete system, the setpoint comparators included, is 436 Hz (2.3 msec.) and
is independent of the setting of the amplifier (min. 0.25 mV/V full scale input).
1.7 LOADCELL CAPACITY, DEAD LOAD
The input sensitivity may be raised up to 1/8 part of the measuring capacity of a loadcell.
This does not effect the accuracy and the available resolution. The dead load on the loadcell may be
compensated up to 50 % (1 mV/V) of the loadcell capacity. This too does not effect the available resolution of
15,000 external divisions over the chosen input sensitivity.
This means that loadcells with an up to 8 times higher capacity as needed may be applied, moreover with 50%
dead load, without loss of speed or accuracy. This is very important for safeguarding a loadcell against heavy
overload and dynamic impulses and vibrations, simply by choosing a far to high loadcell capacity.
1.8 METROLOGY LEGISLATION CE
Based upon the European Legislation, according to EN 45501 the 348-2 is EC approved and certified by Dutch
NMi Certin with nr. - TC 5164 as part of a weighing machine
- T 5170 as a complete not automatic weighing machine
for max. 10,000 divisions and 0.3 µV per division at >
5.6 VAC excitation and > 58 Ohm input impedance.
The length of the loadcell cable is not
limited. No special EMC precautions are required.
The CE marking of the 348-2 is based on EN 50081-1, EN 50082-1, EN 61000-3-2 and EN 45501.
Manual 348-2 V 3.1 Page 6 01-06-2007
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Weightec 348 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Weightec 348 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Weightec 348

Weightec 348 Gebruiksaanwijzing - Nederlands - 49 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info