802458
1
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Operating Manual
ThermoCall TC1.1
Webasto Thermosystems (UK) Ltd.
Webasto House, White Rose Way
Doncaster Carrington, South Yorkshire DN4 5JH
Hotline+44 (1302)381101; Hotfax+44 (1302) 329804
www.webastouk.com
General Information
Dear Webasto Customer,
We thank you for purchasing this new Webasto original accessory.
This product provides you with a comfortable and innovative operating option for
your Webasto auxiliary heating. This operating manual supplements the
explanations by your installing Webasto workshop or service station and once
again, covers all the functions of the ThermoCall TC1.1.
Use
Y
our Webasto auxiliary heating or auxiliary ventilation can be controlled remotely
using DTMF data transmission via telephone. All mobile and fixed network
telephones that allow the transmission of multi-frequency dialing signals are
suitable as operating units.
When you call your ThermoCall TC1.1, the menu-guided system makes it simple for
you to operate your Webasto auxiliary heating/ventilation located in the vehicle. For
example, you can select the operating period or program an internal preset timer.
mode
NOTES:
Please always observe the general operating manual for your Webasto
auxiliary heating and the location of your vehicle before activating the TC 1.1.
In heating mode, the vehicle heating must be set to “warm” before leaving the
vehicle.
The vehicle blower must be set to heating and ventilation mode, (for a 3-level
blower to the 1st level and for a 4-level blower to the 2nd level).
For infinitely variable blowers, set it to at least 1/3 of the maximum.
For Thermo Top and Thermo Top T heating units, the operating period of 20
or 30 minutes must be set in the heating mode.
For Thermo Top Z/C and Thermo Top E heating devices, we recommend
setting the heating time to correspond to the travel time in order to prevent
discharging of the vehicle battery. For a daily travel time of approx. 30
minutes, we recommend limiting the operating period to a maximum of 30
minutes.
For air heaters and truck or bus water heaters, it is possible to program the
operating period up to 120 minutes.
ThermoCall TC1.1 is factory set to 30 minutes of heating.
Ident-Nr. 9005160A
Operation via Fixed Network or Mobile Telephone
Set your fixed network telephone to tone dialing (DTMF). You can find information
about this in the operating manual for your telephone.
This function is already configured for most mobile telephones.
After ordering it from your telephone carrier, you have been assigned a separate
ThermoCall telephone number.
Call the telephone number of your ThermoCall TC1.1. After the connection is
established, you will hear the greeting “WEBASTO THERMOCALL, WELCOME”,
followed by the prompt “PLEASE ENTER YOUR PASSWORD”.
Enter your password (2-digit code) and #. At the factory, the password is set to
“00” (00#). After a correct entry, the available commands are listed in an endless
loop or until the desired function is selected. If your entry is not correct or no
entry is made, you will hear the message “INCORRECT ENTRY” and the available
commands are repeated twice more. Afterward, the telephone connection is
disconnected. The existing menu structure automatically adapts to the current
status of the device.
Operation via Telephone
Function Command
Press Key No. Note
My ThermoCall TC1.1 telephone number:
ACTIVATE auxiliary heating 1
DE-ACTIVATE auxiliary heating / ventilation 1
ACTIVATE auxiliary ventilation 2
EXTEND OPERATING PERIOD for auxiliary
heating / ventilation 2 1
QUERY remaining operating period for
auxiliary heating / ventilation 3 1
ACTIVATE / DE-ACTIVATE internal preset
timer 4 2
QUERY CURRENT TIME 5
LOCATE VEHICLE POSITION 9 6
PROGRAMMING 0 3
Programming
You can reach the programming menu by entering 0 in the main menu
CHANGE PASSWORD
1 new password
(2 digits) # repeat new
password #
4
CHANGE OPERATING PERIOD for
auxiliary heating
2 2 or 3 digits
(10 -120 minutes) #
4 5
CHANGE OPERATING PERIOD for
auxiliary ventilation
3 2 or 3 digits
(10 –120 minutes) #
4 5
PROGRAM CURRENT CLOCK TIME
4 2 digits ( 23 hours)
and 2 digits ( 59 minutes)
4
ACTIVATION TIME for auxiliary
heating
5 2 digits ( 23 hours)
and 2 digits ( 59 minutes)
4
ACTIVATION TIME for auxiliary
ventilation
6 2 digits ( 23 hours)
and 2 digits ( 59 minutes)
4
QUIT PROGRAMMING 0
Operation via Push-Button Switch
A Push-Button is included in the delivery. This must be installed if you have no
preset timer or Telestart and is used to activate and display the current operating
mode of your auxiliary heating.
Pressing the button repeats the last control function that was activated via
telephone. If the system is activated by pressing the button, this ends the current
heating or ventilation cycle
LED steady light Æ Auxiliary heating active
LED blinking slowly Æ Auxiliary ventilation active
LED blinking fast Æ Immediately after button is pressed
Note Comment
1 Not present when the system was activated via the external preset
timer.
2
Switches the auxiliary heating or auxiliary ventilation on at the
programmed time for the programmed operating period.
IMPORTANT: Only one heating or ventilation process is activated.
For a repeat process, another activation of the preset timer is
required.
3 If no entry is made within 10 seconds, ThermoCall automatically
returns to the main menu.
4
If the entry was incorrect or no entry is made within 5 seconds,
ThermoCall returns to the programming menu with the message
“INCORRECT ENTRY”. The previous setting remains unchanged.
5
The entered minute value is saved as the new operating period for
the auxiliary heating or auxiliary ventilation. At the factory, the
heating and ventilation periods are set to 30 minutes.
6 If an external GPS- Modul is attached
Character Legend
01234
56789 Telephone keys (see telephone manual)
Press key(s)
“xx” ThermoCall text
# “Hash” key
ł Blank space (see telephone manual)
Less than or equal to
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Webasto ThermoCall TC1.1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Webasto ThermoCall TC1.1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0.19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Webasto ThermoCall TC1.1

Webasto ThermoCall TC1.1 Gebruiksaanwijzing - Nederlands - 4 pagina's

Webasto ThermoCall TC1.1 Gebruiksaanwijzing - Deutsch - 4 pagina's

Webasto ThermoCall TC1.1 Gebruiksaanwijzing - Français - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info