120859

Wave Ceptor 2554 Handleiding

2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
USER’S GUIDE 2554
2
About the Receive Indicator
The receive indicator shows the strength of the calibration signal being received. For best
reception, be sure to keep the watch in a location where signal strength is strongest.
Weak
Strong
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receive indicator to indicate signal strength.
• Use the receive indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• The receive indicator remains on the display in all modes following reception of the
time calibration signal and calibration of the watch’s time setting. The receive
indicator does not appear if signal reception was unsuccessful or after manual
adjustment of the current time setting.
About Auto Receive
When auto receive is turned on, the watch automatically starts to receive the time
calibration signal when the time in the Timekeeping Mode reaches 2:00 AM, 4:00 AM
and 6:00 AM each day (calibration times).
Note
• The auto receive operation is performed only if the watch is in the Timekeeping or
World Time Mode when one of the calibration times is reached.
It is not performed if a calibration time is reached while you are making settings
(while settings are flashing on the display), while an alarm is sounding.
• Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can easily receive the signal.
• The receive indicator indicates that either the 2:00 AM, 4:00 AM, or 6:00 AM
calibration signal reception was successful. Note, however, that the receive indicator
is cleared from the display at 3:00 AM each day.
• If you do not see the receive indicator except for the above reason, it means there
was some problem with the calibration reception operation. Either perform reception
manually, or make sure the watch is set up properly to receive the time calibration
signal for the next automatic reception time.
• Though this watch is designed to receive both time data (hour, minutes, seconds)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
• The receive indicator (
) appears only when the watch is able to successfully
receive both time and date data. It does not appear when only time data is received.
When time and date data is received: Receive indicator (
) appears.
When time data only is received: Receive indicator (
) does not appear.
• Normally, the signal reception date shown by the Last Signal screen is the date data
included in the received time calibration signal. When only time data is received,
however, the Last Signal screen shows date as kept in the Timekeeping Mode at the
time of signal reception.
• When auto receive is turned on, the watch receives the calibration signal for two to
six minutes each day when the Timekeeping Mode time reaches 2:00 AM, 4:00 AM
and 6:00 AM. Do not operate any of the watch’s buttons within six minutes prior to or
following the calibration times. Doing so can interfere with correct calibration.
• Remember that reception of the calibration signal depends on the time kept in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows 2:00 AM, 4:00 AM and 6:00 AM, regardless of whether or not the
Timekeeping Mode time is actually the correct time.
• When two or three receptions are successful, the watch uses the data of the last
reception for calibration. When only one reception is successful, the watch uses the
data of the successful reception.
To turn auto receive on and off
1. In the Timekeeping Mode, hold down A until the
current auto receive on/off setting to flash, which
indicates the setting screen.
2. Press D to toggle auto receive on (
ONON
ONON
ON) and off (
OFOF
OFOF
OF).
3. Press A to exit the setting screen.
Setting the Time and Date Manually
Make sure you select your Home City code (the city code whose time and date you
are setting) before change the current time and date settings. World Time Mode times
are all displayed in accordance with the Timekeeping Mode settings. Because of this,
World Time Mode times will not be correct if you do not select the proper Home City
code before setting the time and date in the Timekeeping Mode.
To set the current time and date manually
1. In the Timekeeping Mode, hold down A until the
current auto receive on/off setting to flash, which
indicates the setting screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds
Auto
Receive
DST
City Code
12/24-Hour
Format
Month
Year Minutes
Hour
Day
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
ScreenSetting
Auto Receive
City code
DST
Button Operations
Press D to toggle auto receive on and off.
Use D (+) and B (–) to change the
setting.
Press D to toggle between Daylight Saving
Time (
ONON
ONON
ON) and standard time (
OFOF
OFOF
OF).
• Pressing D performs a different operation
when BER, PAR, LON or ATH is selected
as Home City Code. See “Auto Summer
Time (DST) Switching”.
12/24-Hour format
Hour, Minutes
Seconds
Year
Month, Day
Press D to toggle between 12-hour (12H)
and 24-hour (24H) timekeeping.
Use D (+) and B (–) to change the
setting.
Press D to reset the seconds to 00.
Use D (+) and B (–) to change the
setting.
4. Press A to exit the setting screen.
• The auto receive setting is used for time calibration signal reception only. See “About
Auto Receive” for details.
• See “City Code Table” for a complete list of available city codes.
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
Current time in the
selected city code
(Hour : Minutes Seconds)
City code
Home city time
World Time
The World Time shows the current time in 30 cities (29
time zones) around the world.
• If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City settings and
make the necessary changes.
• You can change the DST (Daylight Saving Time)/
Standard Time settings for each city code in the
Timekeeping Mode.
• The watch will perform a signal receive operation even if
it is in the World Time Mode when a calibration time is
reached. If this happens, the World Time Mode time
settings will be adjusted in accordance with the
Timekeeping Mode’s Home City time.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
DST indicator
To view the time in another city code
In the World Time Mode, press D to scroll city codes (time zones) to the east or A to
scroll to the west.
• For full information on city codes, see the “City Code Table”.
Alarms
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm. One of the one-time
alarms functions as a “target alarm,” which counts the
time remaining from the current Timekeeping Mode time
to the target alarm time.
Also use the Alarm Mode to turn the Hourly Time Signal
(SIG) on and off.
• There are five alarms numbered AL1 through AL3,
TAL,and SNZ. You can configure SNZ as a
snooze alarm only. Alarms AL1 through TAL
(target alarm) can be used as one-time alarms only.
• Alarm settings (and Hourly Time Signal settings) are
available in the Alarm Mode, which you enter by
pressing C.
Alarm time (Hour : Minutes)
Home city time
Alarm number
Countdown
(Hours : Minutes Seconds)
Target alarm screen
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Use C to move the flashing in the sequence shown
below to select other settings.
MinutesHour
On/off status
AL1 AL2 AL3
SIG SNZ TAL
4. While a setting is flashing, use D and B to change it.
• While the hour or minute setting is flashing, use D (+) and B (–) to change it.
• While a one-time alarm or the snooze on/off setting is flashing, use D to toggle it
on (ON) and off (OF).
5. Press A to exit the setting screen.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Wave Ceptor 2554 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Wave Ceptor 2554 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info