805490
9
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
9
Type of the
Heating &
Cooling
commutation
(There is a 2
minutes standby
without control to
avoid hot / cold
overlap)
rF: The Heating & Cooling mode will be done by the Master HC thermostat WFHT-
BASICH&C-BUS.
* Generally use when separate system is installed. (Boiler, water chillers...)
CtAC: The Heating & Cooling mode will be done by the Heat Pump connected on
the special input of your RF receiver (see the wiring for more explanation)
* Generally use when manual or automatic reversible Heat pump
SEnS: The heating & Cooling mode will be done by the WFH-SENSOR installed on
the incoming pipe of the manifolds and connected on the special input on RF
receiver (see the wiring for more explanation) * Generally use when reversible heat
pump without Heat & Cool information and control is installed.
for humidity input, then you need to connect a NTC or humidity sensor (refer to
chapter 10.A)
for External control, use this input (free contact) to switch OFF the installation; per
example you can connect a GSM module. (refer to chapter 10.B)
The following parameters are only available if a water humidity sensor (NTC 10K or free contact sensor) is
connected and installed on the incoming pipe of the manifolds
(See the schematic and system drawing to install the sensor)
Setting level to switch off the cooling function to avoid
residual humidity in the house:
When the water temperature in the pipe decrease
under this level during the time of the anti short cycle
adjusted on “F9” the cooling function will be stopped.
Press (OK) to view the instantaneous value measured
by the sensor.
Default: 18°C
Adjustable: 5 to 25°C
Minimum time to decide to stop the cooling function
when the water temperature decreases under the “F8
level.
Default: 30
Adjustable: 00 to 60min
Type of degrees displayed
°C: Celsius degrees.
°F: Fahrenheit degrees.
Type of time displayed
Default: 24H00
Adjustable: 12:00 am/pm
Selection of the proportional band (PWM) duration in
minutes
You could decrease this time up to 15min only if your
installation as fast thermal reacting behavior
(Liquid concrete floor, ...)
Default: 20 minutes
Adjustable: 0 to 120 min
Value of the proportional band (PWM)
Adjust this value like this:
A well insulated house « 1.5°C »
A not insulated house « 4°C »
Default: 3.0°C
Adjustable: 0.1 to 6°C
Press (OK) during 5 seconds to reset the installation.
All parameters are replaced by default value.
Master Heat&Cool thermostat Bus configuration mode (see the corresponding section)
Standard thermostat Bus configuration mode (see the corresponding section)
Press (OK) on this parameter to exit the parameters menu end come back to the main display.
8. Thermostat alarm
- You could see the alarm on the Master (Red blinking LED on the concerned zone and alarm sound).
To stop immediately the alarm sound, press the (OK) key.
- If an alarm is detected on one zone, the regulation will be maintained on this zone by average of the actual room
temperatures of the other zones used on the Master.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Watts WFHC Master H C-Bus slave bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Watts WFHC Master H C-Bus slave in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 3.11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info