694510
26
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
26
GB
When using an existing chimney, make sure to check whether the chimney is properly insulated and is large
enough for the concentric channel system. If they chimney was previously used for a wood or coal  replace, it
must be professionally cleaned  rst. To connect a gas  replace to an existing chimney, please use the appropriate
connection sets by M&G or Ontop Metaloterm.
Gas connection
Use a feed pipe with an approved G3/8” stop cock with coupling.
De-aerate the supply pipe before  tting and fastening the appliance.
Avoid tension on the operating valve and pipes to avoid gas leakage.
Check if the connection is gastight.
Placing the concentric channel system
The combination of the device and the WANDERS concentric channel system (Ø 100 mm - Ø 150 mm by M&G or Ontop
Metaloterm) is approved in accordance with the European CE directive for appliances burning gaseous fuels. Therefore, only
this system may be used in combination with the device. The warranty on the device expires if it is (partly or completely)
installed in combination with a di erent channel system. The WANDERS concentric channel system (Ø 100 mm - Ø 150 mm)
can be used in new construction as well as existing chimneys.
Bracketing the channel
Secure the concentric system with several approved mounting brackets, so that the device does not bear the weight of the
channel system. Keep the following in mind;
Place the  rst mounting bracket no more than 0.5 metres from the device.
Place a mounting bracket no more than 0.1 metres away from every bend, in the event that there is more than 0.25 metres
between two bends. If two bends are less than 0.25 metres apart, only 1 mounting bracket will have to be placed between
the bends.
Place a mounting bracket on horizontal and diagonal parts at at least 1-metre intervals.
Place a mounting bracket on vertical parts at at least 2-metre intervals. Make sure to secure a roof duct with guy wires if it
protrudes from the duct by more than 1.5 metres. Use four screws to secure the façade duct on the outside.
Instructions for placing the out ow
The out ow of the pipe system can be placed on top of the roof or against the side wall
of the house.
Out ow through the top of the roof (type C31)
When placing the out ow on top of the roof, make sure that there is a distance of at least
50 cm between the out ow and the edges of the roof, with the exception of a possible
existing ridge. You must also take the place of the out ow into account in relation to the
existing ventilation openings, movable windows and combustion air supply provisions.
Please consult the national and local requirements.
Out ow through the wall (type C11)
When installed in a side wall, the outlet must be at least 50 centimetres removed from corners,
roof overhangs, gutters, balconies and the like. If the outlet extends to at least the front of the
overhanging element, this distance does not apply. To prevent water from entering the outlet, the
façade duct can be installed at a slight angle to improve drainage.
You must also take into consideration the place of the out ow in relation to the
existing ventilation openings, movable windows and combustion air supply
provisions. Please consult the national and local requirements.
Min.
50 cm
Min.
50 cm
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Wanders Larix bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Wanders Larix in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 6,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info