Handleiding WOLF-Garten Esprit 34 E (pagina 10 van 28) (Nederlands, Duits, Engels, Frans, Italiaans, Pools, Deens, Zweeds, Noors, Fins)

638498

Verklein

Vergroot

Pagina terug

1/28

Pagina verder

Safety instructions

when in good condition.

• Check the work tool to make certain that the mounting elements

are tightly fitted for damage or serious wear.

• Observe the installation instructions when replacing parts.

• Inspect the catcher bag frequently for wear and deformation.

• Check the condition of all outside cables. Ageing and damaged

cables must be replaced by a qualified person.

• Before adjusting or cleaning the tool and before checking for

a caught or damaged connecting cable, switch off the tool and

disconnect the mains plug.

• Before using, ensure (visually) that the cutting blades and their

attaching parts are not blunt or damaged. Replace blunt or

damaged cutting blades by whole sets to avoid imbalance.

3. Cable

•

Please work with safety cables from WOLF. For the connection only

lines which are not lighter than rubber hose lines H0 7 RN-F to DIN

with a minimum diameter of 3 x 1,5 mm

must be used.

•

They must be waterproofmobile decvices that are used outdoors must

be connected via a residual current circuit breaker.

• Use a leakage-protective system (RCD) with a leakage current of

no more than 30 mA.

• Attach connection cable to traction relief. Make sure that in does

not rub against edges, pointed or sharp objects. Do not squeeze

cable through door or window gaps.

• Switching devices must not be removed or bridged (e.g. tying of

switching lever to guide spar).

4. Starting the Motor:

• S

witch on motor only when your feet are at a safe distance from the

mower chassis and when standing on firm ground - not in high grass;

• Do not tilt the mower when starting the motor unless the mower

must be tilted for starting. If so, do not tilt the mower more than

absolutely necessary and lift only the part farthest from the

user. Always ensure that both of your hands are in the working

positions before replacing the mower on the ground.

•

Do not start the engine if you are standing in front of the ejection channel.

5. During work - for your Safety:

• ATTENTION - DANGER! Keep hands away from rotating cutter

blade and remember that the blade continues to rotate for a short

while after the motor has been switched off;

• Always walk behind the handle bars, holding the upper handle grip

with both hands;

• Keep feet away from the mower chassis and be extra carefull

when mowing on hills or slopes to prevent slipping. Mow across

the hill, if possible. Mow forward at walking pace, never run;

• Avoid pulling the mower backwards (towards you) during work;

• Switch off motor before tilting or lifting the mower and when

pushing off the lawn area;

•

Never use the mower when the protective parts are damaged or safety

equipment such as the deflector and/or grass catching parts are missing;

• Use the height adjustment only when the mower is stationary and

the rotating blade has come to a complete standstill;

• Before removing the grassbox switch off the motor and wait until

the rotating blade has come to a complete standstill;

• Never push mower over gravel with running motor;

• If possible, avoid mowing in wet coditions;

• Switch off motor and remove cable plug socket before working at

the cutter blades, before making any adjustments, when cable has

become entangled:

a) before leaving the mower unattended,

b) before attempting to clear a blockade underneath chassis or at

rear throe-out,

c) before inspecting, cleaning or working on the mower,

d) immediately after your mower blade has hit a foreign and hard

object. Check the condition of the deck and cutter blade before

switching on again,

e) immediately when your mower starts to vibrate strongly. Locate

the reason for the vibration and remedy.

• If your mower has a power-drive do switch the power-drive off

before starting motor or engine.

• Should the power cord be damaged during use, immediately

disconnect it from the mains. Do not touch the cable until it has

been disconnected from the mains.

6. Maintenance:

• Switch off motor and remove mains plug before carrying out any

repairs or maintenance to your mower;

• Do not clean your mower with a hose pipe - and particularly not

with a high-pressure spray;

• Inspect regularly all visible nuts and bolts - particularly of the

cutter blade - for their tightness;

•

ATTENTION! Sharpening and changing of cutter blades should

be done by a qualified service centre because it is necessary

that the correct balance after fixing is guaranteed;

•

Damaged and worn parts must always be replaced with original WOLF

replacement parts as otherwise your guarantee will be invalidated;

•

Your service centre should check your mower regularly and particularly

after any hard obstacle hat hit the chassis and/or the cutter blades;

• Store your mower only in a dry room.

• If cutter blade hits a hard foreign object whilst mowing switch of

motor immediately, remove safety key and check cutter blade

carefully for damage. Please observe these hints, as they help

you to prevent damage or even accidents!

• Conduct maintenance and cleaning work only when the motor is

switched off and the key has been removed.

Operation

Operating times

Please check noise abatement regulations prevailing in your

country.

Attaching of grassbox (fig. B1)

Lift deflector lid, locate grassbox hook into opening of chassis

(see arrow) and replace lid.

Adjustment of cutting height Esprit/Premio 34/36 E (fig. B2)

Only when mower is stationary and rotating blade has come

to complete standstill. Press button (a) and push chassis

downwards or pull upwards, as required. Release button at

required cutting height (see indicator b).

Assembly

Fixing of handle and adjustment of height (fig. M1/M2/M3/M4)

ATTENTION! Take care that the switch cable does not

become caught and crushed when folding the handle frame.

Fold upper handle section forward. Tighten hand wheels

firmly.

Premio 32 E:

Fold complete handle backwards and tighten firmly.

Esprit/Premio 34/36 E:

Fold complete handle backwards, position at the correct

height and tighten firmly.

Folding of handle frame (fig. M5)

ATTENTION! Take care that the switch cable does not

become caught and crushed when folding the handle frame.

Note! Unscrew the lower hand wheels (1) for about 2 cm/.1”

either side, pull handle frame (2) either side, pull handle

frame clear of recesses until it can be folded forward easily.

Assembly of cable relief holder (fig. M6/M7)

Adjustment of cutting height to prepare for scarifying Esprit/

Premio 34/36 E (fig. B2)

Press button (a), pushing chassis down byholding front grip (c)

at the same time until grey area appears at the indicator (b).

Use of height adjustment Premio 32 E (fig. B3)

Only when mower is stationary and rotating blade has

come to complete standstill. Holdmowerbyhandle grip

fittedon the rearof the chassis andlift slightly. Pull outblack

knobain the centre of left-hand wheels at the rear. Hold

knob and push wheel upwards or downwards allowing knob

to engage into one of the position holes as required (follow

indicator to determine cutting height). Proceed with left-hand

wheel at front of chassis in the same way.

WOLF-Garten Esprit 34 E Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info