540503
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
3. Adjust for Maximum Eye Relief
Before the final tightening of the scope rings, adjust for
maximum eye relief to avoid injury from recoil.
A. With the riflescope set at the lowest magnification, slide the scope
as far forward as possible in the rings.
B. While viewing through the scope in the normal shooting position,
slowly slide the scope back towards you. When you feel you
just
hit the full field of view, stop. Without disturbing the front-back
setting, slowly rotate the scope until the elevation dial is at the
top of the scope and the vertical crosshair of the reticle matches
the vertical axis of the rifle. Using a visual vertical reference such
as the edge of a building or telephone pole can help with this.
C. Tighten rings per the manufacturer’s instructions.
Initial bore sighting of the riflescope at a distance of 50 yards will
save you time and money at the range. This can be done using a bore
sighting tool, following the manufacturer’s instructions. If you have a
bolt action rifle, you can bore sight without a tool.
4. Bore Sighting
5. Base Adjustments and Shimming
Place the rifle solidly on a bench, remove the bolt, sight through
the bore, and center the target inside the barrel. With the bulls-eye
centered in the bore, make windage and elevation adjustments until
the reticle crosshair is also centered over the bulls-eye. If possible,
make initial windage adjustments using the mounting base rather
than the riflescope’s windage dial.
You will get maximum adjustablility and performance from your Crossfire riflescope if the windage and elevation adjustments are near center.
Though Vortex riflescopes come centered from the factory, you will need to make some adjustments when initially sighting in your scope. Many
ring and base setups allow you to adjust windage at the base mount. If possible, use these adjustments for initial windage change. Though not
usually necessary, you can correct the elevation adjustments using shims under the base mount.
Assuming typical ring spacing of 3.25”, a shim of .001” will
yield 1” at 100 yards, 2” at 200 yards, and so on.
Final sight-in should be done at the range using the exact
ammunition you expect to hunt or shoot with. Set the parallax
adjustment on AO models to match the distance being used for
sight-in. After the scope has been bore-sighted:
6. The Final Range Sight-In
Shim under the front base for more down adjustability and under
the rear base (nearest shooter) for more up adjustability.
If large windage/elevation corrections have been made using bases or shims, it may be
necessary to have the rings lapped. Consult a quali ed gunsmith if you’re unsure of
this procedure.
A. Fire a shot or two to check that you’re roughly on target. If necessary, adjust the
reticle to put you near the center of the target (see page 7).
B. Next, fire a three-shot group as precisely as possible. Using the center of this
group as a reference, make any necessary correction adjustments for windage and
elevation. Adjust the dials in the direction you wish the group to move.
C. Fire a final three-shot group to confirm your adjustment and repeat until you
achieve satisfactory results.
Riflescope Maintenance
Your Crossfire riflescope will require very little routine maintenance other than periodically cleaning the exterior lenses. All components of
Vortex riflescopes are permanently lubricated so no additional lubricant should be applied.
Avoid storage in direct sunlight or hot locations since high
temperatures can adversely affect internal lubricants. Do not
attempt to disassemble any components of your ri escope.
When cleaning the lenses, be sure to use products such as the
Vortex Lens Pen or the Fog Free lens cleaning kits that are designed
for use on coated optical lenses. Be sure to blow away any dust or
grit on the lenses prior to wiping the surfaces. Using your breath, a
very small amount of water, or pure alcohol can help remove oil and
dried water spots.
Lens Care
Clean the exterior of the riflescope by wiping with the soft, dry
cleaning cloth provided with the Crossfire riflescope.
Riflescope Body Care
www.vortexoptics.com
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vortex Crossfire Riflescope bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vortex Crossfire Riflescope in de taal/talen: Engels als bijlage per email.

De handleiding is 0,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info