764165
6
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
6
EN
WWW.VONROC.COM
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-3.
1. Carry handle
2. Lock (float switch)
3. Float on/off switch
4. Base
5. Hose connector
6. Water outlet elbow connector
7. Water outlet
8. Vent hole
3. ASSEMBLY
The larger the hose and hose connector
diameter, the greater the flow.
32mm (inner diameter) hose must be used
to achieve maximum flow rate.
The lower the delivery height, the greater
the flow.
Attaching the outlet hose (Fig. A, B)
1. Decide which hose diameter you are going to
use. See figure B.
2. Cut off the smaller steps of the hose connector
(5) that are not needed, using a suitable knife
or saw (not included).This removes unnecessary
flow restrictions and ensures maximum pump
capacity and water flow.
3. Screw the outlet elbow connector (6) into the
water outlet (7).
4. Screw the hose connector (5) on the outlet
elbow (6).
5. Fit the hose on to the hose connector (5) and
secure with a stainless steel hose clamp (not
included).
6. Attach a suitable rope (not included) to the
carry handle (1), to lower the pump into deep
water and to lift the pump back out of the wa-
ter. Never lower or lift the pump by its cable.
4. OPERATION
Never use this pump in a pond or swimming
pool while people are present in the water!
Never pull the pump by its power cord. The
pump must be carried by, and placed in the
water using the carry handle (1) or if the
water is deep, be lowered on a rope tied to
the carry handle (1).
Always have the pump switched off and the
plug removed from the power socket before
placing it in or removing it from the water.
Only switch the power back on with dry
hands.
Never run this pump dry - out of the water.
If the appliance overheats, the thermal
cut-out will switch it off. If this happens
wait 5 minutes before using the pump
again.
Automatic air bleed valve: The automatic air
bleed valve eliminates any air pockets in the
pump. During this process, air escapes
through the vent hole (8) and air bubbles
appear underwater. This is not a defect of
your pump, but serves to remove air from
the pump. It may take several seconds for
the air to escape when the pump is
immersed for the first time.
Automatic operation
The cable length between the float switch
(3) and the float switch lock (2) must
always be at least 10 cm.
1. To adjust the cut-in and cut-out height, attach
the float switch (3) cable to the float switch lock
(2) at the required length.
2. Lower the pump into water. It would be advisa-
ble to stand the pump on a solid platform at the
bottom to keep it upright, if practical to do so.
Ensure there are no obstructions around the in-
let openings around the base of the pump. The
inlet openings must be clear of mud or sludge
at the bottom of a pool.
3. Connect the mains plug.
4. When the pump is lowered into the water and
the power is switched on, it will start to operate
as soon as the floating switch (3) reaches the
minimum activation height (approx. 50cm) in
the water.
5. The pump switches off as soon as the float
switch (3) has reached the switch-off height
(approx. 5cm) due to the falling water level.
6. Ensure that the float switch (3) is not obstruct-
ed in any way.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vonroc SP502AC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vonroc SP502AC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 6,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info