764115
10
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
10
EN
WWW.VONROC.COM
Checking the battery charging status (Fig. C-2)
To check the battery charge status, push the
button (28) on battery shortly.
The battery has 3 lights indicating the charge
level, the more lights that burn, the more charge
the battery has left.
When the lights are not burning it means the bat-
tery is empty and must be charged immediately.
Charging the battery with the charger (Fig. C-2)
1. Take the battery (4) from the machine.
2. Turn the battery (4) to upside down position and
slide it onto the charger (30) as shown in Fig.
C-2.
3. Push the battery until it is fully pushed into the
slot.
4. Plug the charger plug into an electrical outlet
and wait for a while. The LED indicators on the
charger (31) will lighten up and show the char-
ger status.
The charger has 2 LED indicators (29) which indi-
cate the status of the charging process:
Red LED Status Green LED status Charger status
Off Off No power
Off On
Standby mode:
- No battery is
inserted or,
- Battery inserted
but charging has
finished
On Off Battery charging in
progress
Fully charging the 2Ah battery may take up to
60 minutes.
Fully charging the 4Ah battery may take up to
120 minutes. After the battery is fully charged
remove the charger plug from the outlet and
remove the battery from the charger.
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
Connecting the motor unit to the spray unit
(Fig. D)
With one hand hold the motor unit (8) straight
up and with the other hand place the spray unit
(7) on a 90˚ angle onto the motor unit (8). Like
show in figure D.
Align the spray unit (7) slot with the notch insi-
de the motor unit (8). Rotate the spray unit (7)
90 degrees down until you hear a click.
Disconnecing the motor unit and spray unit (Fig. E.)
Hold the motor unit (8) and press the discon-
nect latch (6) in the direction to the spray unit
(7) and turn 90˚ degrees to take off the spray
unit (7).
Connecting and disconnecting the container to the
spray unit.
To connect: Align the container (11) with the
container cap(10) and tighten.
To disconnect: Loosen the container (11) from
the container cap (10)
Replacing the nozzle and nozzle needle
The nozzle will be assembled on the spray gun
when taken out of the box. To replace the nozzle
follow the following steps.
Loosen the nozzle nut (17) and remove it.
Take out the nozzle head (15) and Nozzle (14)
from the machine.
Loosen the nozzle needle (13) by using the
needle key (18) like show in figure I.
Take the new nozzle needle (24 or 26) and
place it back in the spray unit and tighten by
using the nozzle key (18)
Take the new nozzle (25 or 27) and attach it to
the nozzle head (15)
Place the nozzle head (15) and nozzle assembly
back in the spray unit
Close it by tightening the Nozzle nut (17).
4. OPERATION
Preparing the spray gun for use
Step 1: Viscosity/diluting of the paint
This appliance can process spray materials up to
max. 70 DIN/sec (viscosity). Low-viscosity coating
substances, water- and solvent based paints, fin-
ishes, primers, 2 component paint, clear finishes,
staining sealers and wood sealer preservatives
often do not need diluting. High-viscosity Wall
paints, thick varnishes and thick stains often do
need diluting.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vonroc S3-SG502DC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vonroc S3-SG502DC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 10,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info