764103
10
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
10
EN
WWW.VONROC.COM
To stop the machine, release the on/off switch (2).
Adjusting the base plate (Fig. B)
Due to its movability, the baseplate (7) angle
adapts to the workpiece. Furthermore, the length
of the baseplate can be adjusted depending on the
required sawing depth.
1. Loosen the baseplate bolts (11) using the hex
key (10) provided.
2. Adjust the baseplate (7).
3. Tighten the baseplate bolts (11) using the hex
key (10) provided. It is possible to store the hex
key onto the machine, as shown on Fig. B.
Plunge cutting (Fig. D)
Plunge cutting may only be used on soft materials
such as wood, aerated concrete, gypsum plaster
boards, etc. However, this requires a certain practi-
se and is only possible with short saw blades.
1.
Place the saw onto the workpiece and switch it on.
2. Ensure that the bottom edge of the footplate
rests on the workpiece surface as shown.
3. Slowly saw into the workpiece at an angle, mo-
ving the saw to a vertical position and continue
to saw along the cutting line.
4. Switch the saw off and lift off the workpiece
when the work is complete.
Flush cutting (Fig. E)
Elastic bi-metal saw blades allow you to saw
protruding objects (e,g, water pipes, iron bars, etc,)
nearby the wall.
1. Apply the saw blade directly to the wall and
bend slightly so that the footplate rests against
the wall. Pay attention that the saw blade
always extends beyond the diameter of the
material being worked.
2.
Switch the machine on and saw off the workpiece
keeping constant lateral pressure against the wall.
Optimum use
Adjust saw blade and stroke rate to suit the ma-
terial to be processed. For right radius curves it
is best to use a narrow saw blade. Apply coolant
or lubricant to deal with the fluttering produced
along the cut line when sawing metal.
Check wood, chip boards, building materials
etc, for hard materials (nails, screws etc.), befo-
re sawing and remove them, if necessary.
Clamp material well. Do not support the workpie-
ce with hand or foot. Do not touch objects or the
floor with the saw running (danger of backlash).
Put the footplate on the surface of the workpie-
ce, and saw through it with constant contact
pressure or feed. If the saw blade seizes switch
the machine off immediately. Spread the gap
with a suitable tool and pull out the saw blade.
After finishing work, switch off the machine and
only put down after it has come to a complete
standstill.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
battery pack from the machine.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately
and disposed of in an environmentally friendly way.
WARRANTY
VONROC products are developed to the highest
quality standards and are guaranteed free of defects
in both materials and workmanship for the period
lawfully stipulated starting from the date of original
purchase. Should the product develop any failure
during this period due to defective material and/or
workmanship then contact VONROC directly.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vonroc S-RS501DC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vonroc S-RS501DC in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 3,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info