764058
14
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
14
EN
WWW.VONROC.COM
Bench Mounting
The work bench should be very stable to
eliminate vibration when the router is
operating.
Each table leg has an opening at the bottom for
securing the assembled table to a suitable work
bench. The work bench should be level and strong
enough to support the weight of the table and the
router. Use appropriate fasteners and bolts to secu-
re the router table to the work bench.
Plug in the Router (Fig. A)
Ensure the router table power cord is not
connected into the power outlet.
For safety reasons, your electric router may
only be connected to the mains through the
router table’s safety switch unit.
1. Press the red OFF button to ensure the router
table is switched OFF (0).
2. Ensure the router switch is in the OFF (0) position.
3. Plug the router power cord into the outlet on the
switch box. Secure the router power cord so that
it does not interfere with the operation of the
router.
4. Plug the router table power cord into a power
outlet.
Depth of Cut
The depth of cut affects the rate and quality of
cut. The plunge lock lever on the router holds the
router at the desired height and depth of cut. Refer
to instruction manual that came supplied with your
router for details on how to adjust the depth of cut.
Turning On the Router
Once the router is properly mounted to the router
table, you will be able to operate the router using
the router table switch box.
1. Switch the router to the ON (I) position.
NOTE: The router table is primarily intended for
use with a router fitted with a ‘lock-on’ switch.
If your router does not have this feature it will
be necessary to fix its switch in place using
a clamping device. Ensure to remove this
clamping device as soon as you use the router
without the router table.
2. To start the router press the GREEN ON (I) but-
ton on the router table.
3. To stop router press RED OFF button on the
router table.
Using the router table
Check that the guard is in good working
condition every time you use the machine
and regularly clean the dust and chip guard.
NOTE: If you are using a large diameter routing bit
that removes a large amount of material from the
workpiece it may be necessary to make several
passes, increasing the amount of material removed
each time, in order to prevent overloading your
electric router. If this is the case, adjust the fence
assembly so that a reduced router bit radius is
exposed to the workpiece and make the required
amount of cuts before setting the cutting width as
described below for the final pass.
1. Fit a router bit to the electric router.
2. Adjust the cutting depth, cutting width, feather
boards and fence assembly as described on the
previous pages.
3. Switch the router on using the safety switch
unit and allow it to reach its full speed.
4. Use a push stick to feed the workpiece slowly
and evenly through the rotating router bit.
5. Switch the router table off and allow the bit to
come to a complete stop before you remove the
workpiece from the table top.
Feed direction (Fig. U)
Do not guide the router in the direction of
rotation of the router bit to avoid the danger
of losing control of the router.
Feed the workpiece from right to left. The material
must be fed against the cutting edge of the router
bit, ensure that the workpiece is tight against the
fence.
Fitting and removing router bits
The router can unintentionally start and
cause injury. Disconnect the router table
and your electric router from the mains
before proceeding.
1. Place the router table on its side.
2. From the underside of the worktable fit or
remove a router bit to your router as described
in the router’s operating instructions.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vonroc RT501AC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vonroc RT501AC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools als bijlage per email.

De handleiding is 9,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info