738231
52
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
52
j) Capacity measuring
Make sure that all circuit parts, circuits and components and other objects of measurement are
disconnected from the voltage and discharged.
Always observe polarity with electrolyte capacitors.
- TurntheDMMonandselectmeasuringfunction“Capacity”
- PlugtheredmeasuringlineintotheΩmeasuringjack(E)
and the black measuring line into the COM measuring jack
(D).
Due to the sensitive measuring input, the display
mayshowavalueifthemeasuringlinesare“open”.
Bypressingthebutton“REL”,thedisplayissetto
“0”. The autorange feature is deactivated. This is
recommended for small capacities in the nF range.
- Connect the two measuring prods (red = plus/black = minus)
with the object to be measured (capacitator). After a short
time the display shows the capacity. Wait until the displayed
value has stabilised. This may take a few seconds for ca-
pacities of >40 µF.
- If“OL”(overload)appearsonthedisplay,youhaveexceed-
ed the measuring range.
- Remove the measuring lines from the object to be measured
after completion of the measurement and switch off the DMM.
k) Frequency measurement (electronic)
The DMM can be used to measure and indicate signal voltage frequencies from 600 Hz to 40 MHz. The maximum
input range is 30 Vrms. This measuring function is not suitable for mains voltage measurements. Please observe the
input values in the technical data.
Formainsvoltagemeasurements,usetheadditionalfunction“Hz”inthecorrespondingvoltageandcurrent
measurement ranges.
Proceed as follows to measure frequencies:
- TurntheDMMonandselectmeasuringfunction“Hz”.The
displayindicates“Hz”.
- Plug the red measuring line into the Hz measuring jack (E)
and the black measuring line into the COM measuring jack
(D).
- Connect the two measuring prods to the object to be meas-
ured in parallel (signal generator, circuit, etc.).
- The frequency and corresponding unit are displayed.
- Remove the measuring lines from the object to be meas-
ured after completion of the measurement and switch off the
DMM.
52

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voltcraft VC-450 E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voltcraft VC-450 E in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 9,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info