738481
5
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
b) Additional information on lithium rechargeable batteries
Li-Ion batteries installed in this device require special care during charging/discharging, ope-
ration and handling.
Never destroy or damage the rechargeable battery, do not drop it or puncture it with any
objects. Protect the rechargeable battery from mechanical stress. This may cause a re or
explosion!
Ensure that the device does not overheat during use, charging, discharging, transport and
storage. Do not place the device near heat sources and protect it from exposure to direct
sunlight. If the device overheats, there is a risk of re and explosion!
The device must not exceed a temperature of +60 °C.
If a device is damaged or the outer cover is puffed/swollen, discontinue use of the device. Do
not recharge it. This may cause a re or explosion!
Overview of parts
1
2
3
4
56 7
8
9
10
START
ERR
1 Button for charge level indicator and activation of LED light and power bank function
2 Charge level indicator
3 Protective cover
4 LED light
5 Micro USB charging input “Input”
6 USB charging output “Output”
7 Mechanically coded connection for starter cable
8 MOSFET housing with LED status indicator for starter operation
9 Mechanically coded plug for quick start system
10 Pole terminals (red +, black -)
Start-up and charging
The quick start system must be fully charged before use.
Standard USB quick chargers with a charging current of at least 1 A are suitable for char-
ging. An output charging current of at least 1.5 A is recommended because it shortens the
charging time.
Connect the included charging adapter cable to the USB charger (not included).
Plug the Micro USB cable into the Micro USB charging input “Input” (5).
As soon as your USB charger provides sufcient charging current, the charging process
is indicated by the LEDs of the charge level indicator (2), which light up one after another.
If all 4 LEDs of the charge level indicator light up at the same time or are permanently lit, the
charging process is completed.
Remove the charging cable from the start system.
Briey press the activation button (1) to display the current charge status.
View Meaning
4 LEDs Start system is fully charged and can be used without restriction.
3 LEDs Start system is 75% charged and can be used without restriction.
2 LEDs Start system is 50% charged. It can only be used as power bank or LED light.
1 LED Start system is 25% charged. It can only be used as power bank or LED light.
0 LED Start system is not ready for use and must be charged.
Operation
a) Start support function
The quick start system can support a weak starter battery when starting the engine. During
start-up a very high current is needed. The quick start system emits multiple high current pulses
during the start-up phase. This is usually enough to support a weak starter battery.
Never short-circuit the two pole terminals. This will discharge the quick start system
and damage the rechargeable battery.
To perform start-up, proceed as follows:
Check the charge status of the quick start system. For a start-up support at least 3 LEDs
must light up. If fewer LEDs are lit, the quick start system must rst be charged.
Open the protective cover (3) on the quick start system.
Insert the starter cable plug (9) into the connection for the starter cable (7). The plug is
mechanically coded and ts together only with the correct polarity. Ensure rm and reliable
contact.
The green LED status indicator on the MOSFET housing (8) starts to ash.
Connect the red pole terminal (10) to the plus pole (+) and the black pole terminal (10) to
the minus pole (-) of the car battery. Ensure that the contact is connected properly. Turn the
terminals back and forth to break possible oxide layers on the poles.
Once the contact is established, the green LED glows steadily after a few seconds and you
will hear a short beep. Start your car within 30 seconds. The quick start system now emits
multiple current pulses during the start-up phase. They should be enough to start the engine.
When the engine starts, disconnect the quick start system and remove the starter cable from
the quick start system. Close the connections with the protective cover.
If the engine does not start, disconnect the quick start system. Wait approx. 5 minutes and
then repeat a start-up operation.
If the engine still does not start after three attempts, the start support process must be termi-
nated. Probably, the car battery is defective, or there is another problem. In this case, have
the vehicle checked by a specialist workshop.
LED status indicator on the MOSFET housing (8)
View Meaning
Green ashing Quick start system is ready
Green steady light with beep Start mode is activated
Red steady light Connection error. Please check all contacts
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voltcraft 2127443 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voltcraft 2127443 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info