734994
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
D-304921 SR-740 PG2 Installation Instructions 3
Step 6 Step 7 Step 8
Notes:
1. If the siren is already enrolled, you can
configure the siren parameters and assign
partitions via the “Modify Devices” option
see Step 2.
2. PARTITIONS will appear only if
PARTITIONING was previously enabled in a
panel that supports the Partitioning feature (for
further details, see "Partitioning" in the
PowerMaster Installer Guide).
3. When there is an alarm, the siren will sound
regardless of partition assignment.
Enter PARTITIONS.
See Note 2
Assign partitions to the
detector by pressing the
, and
buttons on the panel
Select the "DEV SETTINGS"
option and refer to the section
below to configure the siren
parameters.
means scroll and select
4
44
4.
. .
. CONFIGURING THE SIREN PARAMETERS
CONFIGURING THE SIREN PARAMETERSCONFIGURING THE SIREN PARAMETERS
CONFIGURING THE SIREN PARAMETERS
Enter the menu and follow the configuration instructions for the SR-740 PG2 outdoor siren as described in the following
table.
Option Configuration Instructions
Here you determine whether or not to activate the strobe alarm, and if activated, whether to activate the strobe until
the alarm system is disarmed, or, for the programmed period of time (see "Siren Configuration" section in the
control panel Installer Guide).
Optional settings: Timer limited (default), Disabled and Until Disarmed
Here you determine whether or not to activate the exit entry beeps, and if enabled, whether to activate in HOME or
AWAY mode.
Optional settings: Disabled (default), Disabled & Home and Enabled.
Here you determine whether or not to enable the squawk, and if enabled, whether to activate the sounder only, or, the
sounder and strobe simultaneously.
Optional settings: Disabled (default), Sounder only, Strobe only and Sounder+strobe.
Here you determine the volume level of the sounder.
Optional settings: Volume HIGH(default), Volume LOW and Volume MID.
Here you determine whether or not the LED will be activated to indicate that the siren is operating.
Optional settings: Disabled (default) and Enabled.
Here you determine whether or not the siren alone will sound a tamper alarm when there is no communication
between the siren and the control panel.
Optional settings: Disabled (default) and Enabled.
5
55
5.
. .
. LOCAL DIAGNOSTICS TE
LOCAL DIAGNOSTICS TELOCAL DIAGNOSTICS TE
LOCAL DIAGNOSTICS TEST
STST
ST
Before testing, remove the plastic cover and then open the
battery cover (see Fig. 2).
A. Press the self-test button once and release it; the following
procedure should occur in turn:
The red LED will switch ON and then OFF, the green LED will
switch ON and then OFF, the strobe light will switch ON and
then OFF and the piezo siren will sound to indicate that the
siren is now fully operational.
B. After 2 seconds the LED blinks 3 times.
The following table indicates received signal strength
indication.
LED response Reception
Green LED blinks Strong
Orange LED blinks Good
Red LED blinks Poor
No blinks No communication
IMPORTANT! Reliable reception must be assured. Therefore,
"poor" signal strength is not acceptable. If you receive a "poor"
signal from the device, re-locate it and re-test until a "good" or
"strong" signal strength is received.
Note: For detailed Diagnostics Test instructions refer to the
control panel Installer Guide.
AUTO TAMPER ALRM
ACTIVITY LED
SOUNDER VOLUME
SQUAWK
EXIT-ENTRY Beeps
STROBE ALARM
DEVICE SETTINGS
SR1: DEV SETTINGS
SR1:P1 P2 P3
SR1:PARTITIONS
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Visonic SR-740 PG2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Visonic SR-740 PG2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info