667349
42
Verklein
Vergroot
Pagina terug
1/548
Pagina verder
0478 201 9906 D - EN
40
8.4 Working area for operator
For safety reasons, the operator
must stay within the working area
(grey area X) for the entire operating
period (while the motor is switched on
or the engine is running), particularly in
order to prevent injuries due to
shredding material that is ejected
backwards.
8.5 Correct machine load
The load on the motor or engine of the
garden shredder must never cause the
speed to drop significantly. Always feed
the garden shredder continuously and
steadily. If the speed drops when working
with the garden shredder, stop feeding the
machine in order to relieve the load on the
motor or engine.
8.6 Overload protection
If an overload of the motor occurs during
operation, the built-in overload protection
device automatically switches off the
motor.
The garden shredder can be started up
again after a cooling period of
approx. 10 minutes. Frequent triggering
of the overload protection may be
attributable to the following causes:
Unsuitable electric cable (Ö 10.1)
Power overload
Machine overloaded due to excessive
quantities of shredding material or blunt
blades
8.7 If the cutting unit of the garden
shredder is blocked
If the cutting unit of the garden shredder
becomes blocked during shredding,
immediately switch off the motor and
disconnect the power cable. Then remove
the feed chute and eliminate the cause of
the fault.
8.8 Feeding the garden shredder
Before feeding the garden shredder,
note the working area. (Ö 8.4)
Start the garden shredder. (Ö 10.3)
Soft material:
Throw organic plant trimmings such as
fruit and vegetable waste, flower
cuttings, leaves, thin branches etc. into
the feed opening (1).
Hard material:
Feed tree and hedge cuttings as well as
branch material slowly into the feed
opening (1). The hard material is
automatically drawn in by the machine.
9.1 Motor restart inhibitor
The machine can only be started via the
switch and not by plugging the electric
cable into the mains socket.
Only switch off the motor when
there is no longer any shredding
material in the machine. Otherwise,
the blade disc may become blocked
when operation is resumed.
7
Risk of injury!
Carefully read the section entitled
"For your safety" (Ö 4.), sub-
section "Working with your
machine" (Ö 4.6) in particular, and
follow all the safety instructions
before feeding the garden
shredder. It is only permitted for
one person to feed the garden
shredder.
Risk of injury!
Never reach into the feed
opening.
8
Damp or wet soft material will
cause blockages in the machine
more quickly. For this reason, feed
the garden shredder more slowly
and pay particular attention to the
motor speed. It should not drop
during feeding.
Cut up thick branches and
branches with side shoots (note the
maximum branch thickness
(Ö 8.3)) beforehand using loppers.
Risk of injury!
The inclined blade unit can cause
branches to kick back.
In order to prevent injuries caused
by kickback, the garden shredder
must be fed with hard material in
the correct manner:
Insert longer branches at a slight
angle and guide them along the
right-hand chute wall to the blade
unit in accordance with the
symbol (2).
Observe the correct motor load.
(Ö 8.5)
9. Safety devices
42

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Viking-GE-150

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Viking GE 150 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Viking GE 150 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 18,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info