596864
4
Verklein
Vergroot
Pagina terug
1/58
Pagina verder
PJD5232/PJD5234/PJD7223
DLP Projector
User Guide
Model No. VS14968/VS14969/VS15115
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
ZZZYLHZVRQLFFRPLQ(QJOLVKRULQVSHFL¿FODQJXDJHVXVLQJWKH5HJLRQDOVHOHFWLRQ
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the follow-
ing two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and receiver.
y Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
y Consult the dealer or an experienced radio/TV technician for help.
Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHG
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
y This Class B digital apparatus complies with Canadian ICES-003.
y Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Volt-
age Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
i
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
RURWKHUGHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
SURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXU
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU
 8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
 5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKH
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
ii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use of
certain hazardous substances in electrical and electronic equipment (RoHS2 Direc-
tive) and is deemed to comply with the maximum concentration values issued by the
European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr
6+
) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex of
the RoHS2 Directives as noted below:
Examples of exempted components are:
1. 0HUFXU\LQFRPSDFWÀXRUHVFHQWODPSVQRWH[FHHGLQJPJSHUODPSDQGLQRWKHU
ODPSVQRWVSHFL¿FDOO\PHQWLRQHGLQWKH$QQH[RI5R+6'LUHFWLYH
2. /HDGLQJODVVRIFDWKRGHUD\WXEHVHOHFWURQLFFRPSRQHQWVÀXRUHVFHQWWXEHVDQG
electronic ceramic parts (e.g. piezoelectronic devices)
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead)
Lead as an allotting element in steel containing up to 0.35% lead by weight, alumin-
ium containing up to 0.4% lead by weight and as a cooper alloy containing up to 4%
lead by weight
iii
Copyright Information
Copyright © ViewSonic
®
Corporation, 2013. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
WKHULJKWWRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFX-
ment may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it
becomes available, please register your product on the Internet at: www.viewsonic.
com. The ViewSonic
®
Wizard CD-ROM also provides an opportunity for you to print
the registration form, which you may mail or fax to ViewSonic.
For Your Records
Product Name: PJD5232/PJD5234/PJD7223
ViewSonic DLP Projector
Model Number: VS14968/VS14969/VS15115
Document Number: PJD5232/PJD5234/PJD7223_UG_ENG Rev. 1A 12-28-12
Serial Number: ______________________________________________
Purchase Date: ______________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
iv
v
Notes on the AC power cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC
outlet, please contact your sales dealer. This projector is equipped with a grounding
type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety
purpose of this grounding type plug. We highly recommend using a video source
device also equipped with a grounding type AC line plug to prevent signal interference
due to voltage fluctuations.
For Australia and!
Mainland China
For the U.S.A. and
Canada
For the U.K.
Ground
For Continental Europe
Ground
Ground
Ground
Table of contents
vi
Introduction ........................................................................................... 1
Projector features ................................................................................................................................... 1
Package contents .................................................................................................................................. 2
Projector overview ................................................................................................................................. 3
Using the product .................................................................................. 5
Control panel .......................................................................................................................................... 5
Connection ports .................................................................................................................................... 6
Remote control ....................................................................................................................................... 7
Installing the Batteries .......................................................................................................................... 10
Remote control operation ..................................................................................................................... 11
Connection .......................................................................................... 12
Connecting a computer or monitor ....................................................................................................... 13
Connecting Video source devices ........................................................................................................ 14
Operation ............................................................................................. 17
Powering on/off the projector ............................................................................................................... 17
Adjusting the projector height .............................................................................................................. 18
Adjusting the Projector Zoom and Focus ............................................................................................. 18
Adjusting Projection Image Size .......................................................................................................... 19
Locking control keys ............................................................................................................................ 20
Setting the presentation timer .............................................................................................................. 21
Menu operation .................................................................................................................................... 22
Maintenance ........................................................................................ 32
Cleaning the lens ................................................................................................................................. 32
Cleaning the projector housing ............................................................................................................ 32
Replacing the Lamp ............................................................................................................................. 33
Specifications ...................................................................................... 35
Dimensions .......................................................................................................................................... 36
Ceiling mount installation ..................................................................................................................... 36
Appendix .............................................................................................. 37
LED Indicator Messages ...................................................................................................................... 37
Compatibility Modes ............................................................................................................................. 38
Troubleshooting ................................................................................................................................... 39
RS-232 Command and Configuration .................................................................................................. 40
IR Control Table ................................................................................................................................... 43
1
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55" Texas Instruments DLP
®
technology
PJD5232/PJD5234/PJD7223: XGA (1024 x 768 pixels)
Compatibility with Macintosh
®
computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
Less than 0.5 W power consumption in standby mode
Presentation timer for better control of time during presentations
Support 3D DLP link
DynamicEco Timer function decreasing the power consumption of the lamp by up to
70% when no input signal can be detected for a set period of time.
D.Eco function decreasing the power consumption of the lamp by up to 70%
directly.
Selectable quick power off function
Switchable normal and economic modes to reduce the power consumption
Note
The information in this manual is subject to change without notices.
The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
2
Package contents
When you unpack the projector, make sure you have all these components:
Note
Contact you dealer immediately if any items are missing, appear damaged, or if the unit
does not work
.
For maximum protection of the product, please save the original shipping carton and
packing materials and repack your product as it was originally packed at the factory if
you need to ship it.
Projector AC Power Cord Remote Control (IR) &
batteries (AAA *2 PCS)
VGA Cable (D-SUB to D-
SUB)
ViewSonic CD Wizard Quick Start Guide
3
Projector overview
Front view
1. Front IR remote control sensor 2. Elevator foot
3. Projection lens 4. Focus ring
5. Security bar 6. Speaker
7. Ventilation holes 8. Zoom ring
9. Control panel 10. Lamp cover
2
7
8
9
3
1
5
6
4
10
4
Rear View
Bottom View
Note
This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package.
Contact your dealer for information to mount the projector on a ceiling.
1. AC power socket 2. Connection ports
3. Kensington lock
1. Security bar 2. Ceiling mount holes
1 3
2
1 3
2
PJD5232 / PJD7223 PJD5234
2
1
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
32
40
150
5
Using the product
Control panel
1. TEMP (Temp LED indicator)
Refer to “LED Indicator Messages”.
2. Keystone/Arrow keys ( /Up, /Down)
Manually correct distorted images resulting from an angled projection.
3. POWER
Turn the projector on or off.
4. POWER (Power LED indicator)
Refer to “LED Indicator Messages”.
5. ENTER/Arrow key ( /Right)
Enacts the selected On-Screen Display (OSD) menu item.
When the On-Screen Display (OSD) menu is activated, #2 #5 and #7 keys are
used as directional arrows to select the desired menu items and to make adjust-
ments.
6. MENU/EXIT
Display or exit the on-screen display menus.
7. SOURCE/Arrow key ( /Left)
Display the source selection bar.
8. LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
MENU
EXIT
POWER
OSCRUE
R
E
TNE
TEMP
LAMP
1
2
3
4
5
2
6
7
8
6
Connection ports
1. AUDIO IN 1
Connect an audio output from the Computer In1 to this jack.
2. S-VIDEO
Connect S-Video output from video equipment to this jack.
3. COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
4. COMPUTER OUT
Connect to a computer display, etc.
5. HDMI
Connect HDMI output from video equipment to this jack.
(This function is available for PJD5234 and PJD7223.)
6. RS-232
When operating the projector via a computer, connect this to the controlling com-
puter's RS-232C port.
7. TYPE B USB
This connector is for firmware update and mouse function support.
8. COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack.
9. VIDEO
Connect composite video output from video equipment to this jack.
10. AUDIO OUT
Connect to a speaker or other audio input equipment.
11. AUDIO IN 2
Connect an audio output from the Computer In2 or video to this jack.
1 2 3
4
6
7
5
10 9
8
11
7
Remote control
1. Power
Turn the projector on or off.
2. VGA1
Display COMPUTER IN 1 signal.
3. Source
Display the source selection bar.
4. Keystone/Arrow keys ( /Up, /Down)
Manually correct distorted images resulting from an angled projection.
5. Left
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys
are used as directional arrows to select the desired menu items and to make
adjustments.
6. My Button
User definable key for customized function
7. Menu
Display on-screen display menus.
8. Right mouse
Perform the right button of the mouse when mouse mode is activated.
9. Left mouse
Perform the left button of the mouse when mouse mode is activated.
4
5
7
9
11
12
10
3
8
6
4
13
14
15
16
17
18
19
24
25
20
21
29
22
23
26
28
27
8
10. Mouse
Switch between the normal and mouse modes.
11. Lock
Activate panel key lock.
12. Pattern
Display embedded test pattern.
13. Blank
Hide the screen picture.
14. D.Eco
Decreases the power consumption of the lamp by up to 70%.
Note: It takes some time to initiate this function. Make sure the projector has been
turned on for more than 4 minutes.
15. Auto Sync
Automatically determines the best picture timings for the displayed image.
Note: Switch input source to Composite/S-Video/HDMI by sequence.
HMI only for PJD5234
16. Video
Switch input source to Composite/S-Video/HDMI by sequence.
17. VGA2
Display COMPUTER IN 2 signal.
18. Color Mode
Select the picture setup mode.
19. Enter
Confirmed selections.
20. Right
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys
are used as directional arrows to select the desired menu items and to make
adjustments.
21. Exit
Goes back to previous OSD menu.
22. Page Up
Perform page up function when mouse mode is activated.
23. Page Down
Perform page down function when mouse mode is activated.
24. Magnify
Magnifies the projected picture size.
25. Volume
Adjust the volume level.
26. Freeze
Freeze the projected image.
27. Mute
Toggles the projector audio between on and off.
9
28. Aspect
Select the display aspect ratio.
29. Timer
Activate P-Timer OSD menu.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connecting a computer"
on page 13 for details.
2. Set the input signal to COMPUTER IN 1 or COMPUTER IN 2.
3. Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse
mode.
4. Perform the desired mouse controls on your remote control.
To move the cursor on the screen, press / / / .
To left-click, press .
To right-click, press .
To operate your display software program (on a connected PC) which responds
to page up/down commands (like Microsoft PowerPoint), press Page Up/Page
Down.
To return to the normal mode, press Mouse again.
10
Installing the Batteries
1. Open the battery cover in the
direction shown.
2. Install batteries as indicated by the
diagram inside the compartment.
3. Close the battery cover into position.
Caution
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
Keep the battery out of the reach of children.
Remove batteries from remote control when not using for extended periods.
Do not recharge the battery or expose the battery to fire or water.
Do not dispose the used battery along with household waste. Dispose
!
used batteries
according to local regulations.
Danger of explosion may happen if batteries are incorrectly replaced. Replace only with
the same type recommended by the manufacturer.
Battery should not be in or near to fire or water, keep batteries in a dark, cool and dry
place.
If suspect battery leakage, wipe out the leakage and then replace a new battery. If the
leakage adheres to your body or clothes, rinse well with water immediately.
11
Remote control operation
Point the remote control at the infrared remote sensor and press a button.
Operating the projector from the
front.
Note
The remote control may not operate when there is sunlight or other strong light such as
a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively high temperature or humidity.
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
12
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important
In the connections shown above, some cables may not be included with the projector
(see "Package contents" on page 2). They are commercially available from electronics
stores.
The connection illustrations above are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
For detailed connection methods, see pages 13-16.
1. Audio cable 2. HDMI cable
3. Composite Video cable 4. S-Video cable
5. VGA (D-Sub) to HDTV (RCA) cable 6. VGA cable (D-Sub to D-Sub)
7. USB cable 8. VGA to DVI-A cable
2
1
1
3 4
5
6 7
6
8
1
PJD5232 / PJD7223
PJD5234
13
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both!
IBM
®
compatibles and Macintosh
®
computers. A Mac adapter is needed if you are!
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of
the computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
Important
Many notebooks do not turn on their external video ports when connected to a
projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display
on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol
on the notebook. Press FN and the labeled function key simultaneously. Refer to your
notebook's documentation to find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen,
you can connect the COMPUTER OUT signal output socket on the projector to an
external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on
page 13.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable
to the!D-Sub input socket of the video monitor.
3. Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
4. Connect the other end of the cable to the COMPUTER OUT socket on the projec-
tor.
14
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one
of the following output sockets:
•HDMI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the
above!connecting methods, however each provides a different level of video quality.
The method!you choose will most likely depend upon the availability of matching
terminals on both the!projector and the Video source device as described below:
Connecting an HDMI source device
Examine your Video source device to determine if it has a set of unused HDMI output
jacks available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI
source device.
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Terminal name Terminal appearance Reference Picture quality
HDMI
HDMI "Connecting an
HDMI source
device" on page 14
Best
S-Video
S-VIDEO "Connecting an S-
Video source
device" on page 15
Good
Video
VIDEO "Connecting a
composite Video
source device" on
page 16
Normal
15
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2. Connect the other end of the cable (with a D-Sub type connector) to the COM-
PUTER IN 1 or COMPUTER IN 2 socket on the projector.
Important
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output
socket available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projec-
tor.
Important
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to
this device using an S-Video connection as this makes an unnecessary second
connection of poorer picture quality. See "Connecting Video source devices" on page
14 for details.
16
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite
Video output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of
the!Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
Important
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source
devices" on page 14 for details.
17
Operation
Powering on/off the projector
Powering on the projector:
1. Complete the AC power cord and peripheral signal cable(s) connections.
2. Press to turn on the projector.
The projector takes a minute or so to warm up.
If the projector is still hot from previous activity, it will run the cooling fan for
approximately 60 seconds before energizing the lamp.
3. Turn on your source (computer, notebook, DVD, etc.).
If you are connecting multiple sources to the projector simultaneously, press
SOURCE on the projector or Source on the remote control to select your
desired signal or press your desired signal key on the remote control.
If the projector doesn't detect a valid signal, the message 'No Signal' will con-
tinue to be displayed.
Be sure the Auto Source function in the Setting menu is On if you want the
projector to automatically search for the signals.
Warning
Never look into the lens when the lamp is on. This can damage your eyes.
This focal point concentrates high temperature. Do not place any object near it to avoid
possible fire hazard.
Powering Off the Projector:
1. Press to turn off the projector lamp. You will see a message "Power off? Press
Power again" appear on the screen.
2. Press again to confirm.
When green mode is turned off, the Power LED begins flashing and the projec-
tor has entered stand-by mode.
When green mode is turned on, the Power LED becomes steady light and the
projector has entered stand-by mode.
If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-by
mode, simply press to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
18
Adjusting the projector height
The projector is equipped with an elevator foot to adjust the image height. To raise or
lower the image, turn the elevator foot to fine-tune the height.
Note
To avoid damaging the projector, make sure that the elevator foot is fully retracted
before placing the projector in its carrying case.
Adjusting the Projector Zoom and Focus
1. Sharpen the image by rotating the focus ring.
2. Adjust the image size by rotating the zoom ring.
Elevator foot
Focus ring
Zoom ring
19
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection
distance.
.
Note
Position the projector in a horizontal position; other positions can cause heat build-up
and damage to the projector.
Keep a space of 30 cm or more between the sides of the projector.
Do not use the projector in a smoky environment. Smoke residue may build-up on
critical parts and damage the projector or its performance.
There is 10% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should
physically test the projection size and distance using the actual projector in situ before
you permanently install it, so as to make allowance for this projector's optical
characteristics. This will help you determine the exact mounting position so that it best
suits your installation location.
Screen size
Diagonal
[inch (cm)]
4 : 3 Screen
Projection distance [inch (m)]
Image height
[inch (cm)]
Vertical offset
[inch (cm)]
(min. zoom) (max. zoom)
40 (102) 62 (1.6) 69 (1.7) 24 (60.96) 3.6 (9.1)
60 (152) 94 (2.4) 103 (2.6) 36 (91.44) 5.4 (13.7)
80 (203) 125 (3.2) 137 (3.5) 48 (121.92) 7.2 (18.2)
100 (254) 156 (4.0) 172 (4.4) 60 (152.4) 9.0 (22.9)
150 (381) 234 (5.9) 257 (6.5) 90 (228.6) 13.5 (34.3)
200 (508) 312 (7.9) 343 (8.7) 120 (304.8) 18.0 (45.7)
250 (635) 390 (9.9) 429 (10.9) 150 (381.0) 22.5 (57.2)
300 (762) 468 (11.9) 515 (13.1) 180 (457.2) 27.0 (68.6)
Maximum zoom
Minimum zoom
Projection distance
Center of lens
Screen
Vertical offset
20
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings
from being changed accidentally (by children, for example). When the Panel Key
Lock is on, no control keys on the projector will operate except Power.
1. Press Lock on the remote control.
2. A confirmation message is displayed. Select Yes to
confirm.
To release panel key lock:
1. Press Lock on the remote control or keypad on the
projector.
2. A confirmation message is displayed. Select Yes to
confirm.
Important
If you press Power to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
Keys on the remote control are still functional when panel key lock is enabled.
21
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you
achieve better time management when giving presentations. Follow these steps to
utilize this function:
1. Press Timer on the remote control to access the Presentation Timer menu or go to
the Option > Presentation Timer menu and press to display the Presentation
Timer page.
2. Highlight Timer Period and decide the timer period by pressing / .
3. Press to highlight Display Timer and choose if you want the timer to show up
on the screen by pressing / .
4. Press to highlight Timer Position and set the timer position by pressing / .
Top-Left Ш Bottom-Left Ш Top-Right Ш Bottom-Right
5. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .
6. To activate the presentation timer, press / to highlight On and exit the menu.
You will see the message displaying on the screen.
7. To cancel the timer, go to the Option > Presentation Timer menu and highlight
Off.
Selection Description
Always Displays the timer on screen throughout the presentation time.
1 Min/2 Min/3 Min Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decrease from the preset time to 0.
22
22
Menu operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
How to operate
1. Press MENU/EXIT on the projector or Menu on the remote control to open the
OSD menu.
2. When OSD is displayed, use / to select any feature in the main menu.
3. After selecting the desired main menu item, press to enter sub-menu for feature
setting.
4. Use / to select the desired item and adjust the settings with / .
5. Press MENU/EXIT on the projector or Menu on the remote control, the screen will
return to the main menu.
6. Press MENU/EXIT twice* on the projector or Exit on the remote control to leave
and save the settings.
*The first press leads you back to the main menu and the second press closes the
OSD menu.
23
Menu tree
Main Menu Sub Menu Settings
Picture
Color Mode Brightest / PC / Movie / ViewMatch / User1 / User2 /
White Board / Black Board / Green Board
Reference Mode Brightest / PC / Movie / ViewMatch
Brightness 0 - 100
Contrast 0 - 100
Color Setting
Color Temp. User/ Cool / Normal / Warm
Red Gain 0 - 100
Green Gain 0 - 100
Blue Gain 0 - 100
User Color
Color Red / Green / Blue /Cyan /
Magenta / Yellow
Hue -99 - +100
Saturation 0 - 199
Gain 0 - 199
White Intensity 0 - 10
Gamma 1 - 8
Aspect Ratio Auto / 4:3 / 16:9 / Anamorphic
Dynamic Mode On / Off
Keystone -40 - +40
3D Settings
3D Sync On / Off
3D Format Auto / Frame Sequential / Frame
Packing / Top-Bottom / Side-by-
Side
3D Invert On / Off
Video/Audio
Frequency 0 - 31
Tracking -5 - +5
H Position -10 - +10
V Position -10 - +3
Zoom 0 - +5
Video Setting
Sharpness 0 - 31
Tint 0 - 100
Saturation 0 - 100
Audio Setting
Volume 0 - 10
Mute On / Off
24
Setting
Projection Front-Table / Front-Ceiling / Rear-Table / Rear-Ceiling
Menu Setting
Menu Position Top-Left / Top-Right / Center / Bot-
tom-Left / Bottom-Right
Menu Display
Time
5 - 60 Sec
OSD Transpar-
ency
Off - 90
HDMI Format Auto / RGB / YCbCr; YPbPr
HDMI Range Enhanced / Normal
Blank Screen Black / Red / Green / Blue / Cyan / Yellow / Magenta /
White
Start up Screen Enter ViewSonic / Blue / Black
Message On / Off
Auto Source On / Off
Auto Power Off Off~30 Minutes
Sleep Timer Off~12 Hours
Standby Setting
Green Mode On / Off
Active VGA Out On / Off
Active audio Out On / Off
Quick Power Off On / Off
Smart Restart On / Off
25
Note
HDMI settings is only for PJD5234.
Option
Closed Caption Off/ CC1~CC4/ T1~T2
Password
Change Pass-
word
Input new pass-
word
Confirm pass-
word
Password Yes / No
Password Delete Input currently
password
Password Delete
Yes/No
Presentation
Timer
Presentation
Timer
On / Off
Timer Period 0 - 240 Min
Display Timer Always / 1 Min / 2 Min / 3 Min /
Never
Timer Position Top-Left / Bottom-Left / Top-Right /
Bottom-Right
Timer Counting
Direction
Count Down / Count Up
High Altitude On / Off
Lamp Setting
Lamp Hours
Lamp Hours
Reset
Yes / No
Eco Mode On / Off
Dynamic Eco
Timer (RC)
Off / 5 / 10 / 15 / 20 / 25 / 30 min
My Button
Brightness / Contrast / Color Setting / Projection /
Menu Position / 3D Setting / Eco Mode / Dynamic
Mode / OSD Transparency / Closed Caption / Auto
Power Off / Sleep Timer / Auto Source
Pattern Off / 1 / 2 / 3 / 4 / 5
Factory Default Yes / No
Language
Information Input Source
Resolution
H. Frequency
V. Frequency
Lamp Hours
26
Picture
Color Mode
There are many factory presets optimized for various types of images.
Brightest: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required.
PC: Is designed for presentations under daylight environment to match PC and
notebook coloring.
Movie: Is appropriate for playing colorful movies. This mode is suitable for viewing
in a blackened (little light) environment
ViewMatch: Switches between high brightness performance and accurate color
performance.
User 1:Memorize user 1 defined settings.
User 2:Memorize user 2 defined settings.
White Board:For white projection screen type.
Black Board:For black projection screen type.
Green Board:For green projection screen type.
Reference Mode
Select a picture mode that best suits your need for the image quality and further fine-
tune the image. This function is only available when User 1 or User 2 is selected.
Brightest: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required.
PC: Is designed for presentations under daylight environment to match PC and
notebook coloring.
Movie: Is appropriate for playing colorful movies. This mode is suitable for viewing
in a blackened (little light) environment
ViewMatch: Switches between high brightness performance and accurate color
performance.
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red Gain, Green Gain, Blue Gain) to customize user color
temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range, hue, saturation and gain according
to your preference.
27
White Intensity
Increase the brightness of white areas.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look
brighter.
Aspect Ratio
Select how the picture fits on the screen:
Auto: Scales an image proportionally to fit the projector's native resolution in its
horizontal or vertical width. You want to make most use of the screen without
altering the source image’s aspect ratio.
4:3: Scales an image so that it is displayed in the center of the screen with a 4:3
aspect ratio.
16:9: Scales an image so that it is displayed in the center of the screen with a 16:9
aspect ratio.
Anamorphic: Minimizes the aspect ratio distortion by maintaining close to the
original aspect ratio in the center of the image and distributing the majority of
distortion at the edges of the displayed image.
Dynamic Mode
Choose “On” to dim the projector lamp which will automatically detect the brightness
level of the content and reduce lamp power consumption (up to 70 percent). Choose
“Off” to turn off Dynamic Mode.
Note
When Dynamic Mode is “On”, Eco Mode will be gray out.
Keystone
Manually correct distorted images resulting from an angled projection.
Press Keystone / on the projector or remote control to display the Keystone
correction page.
Press to correct keystone at the top of the image.
Press to correct keystone at the bottom of the image.
3D Settings
This projector features a 3D function which enables you to enjoy the 3D movies, vid-
eos, and sporting events in a more realistic way by presenting the depth of the
images. You need to wear a pair of 3D glasses to view the 3D images.
3D Sync: When you discover the inversion of the image depth, enable this function
to correct the problem.
3D Format: Use this function to choose an appropriate 3D format if the projector
cannot recognize the 3D format.
If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects
the signal for 3D Sync information and once detected, it projects images in 3D
format automatically. In other cases, you may need to manually select a 3D Sync
format for the projector to project 3D images correctly.
Note
3D Format will be available when 3D Sync is “On”.
28
The default setting is “Auto” when input source is HDMI.
The default setting is “Side-by-Side” when input source is video or computer. “Auto”
will be unavailable.
The brightness level of the projected image will decrease.
The Color Mode cannot be adjusted.
•3D Invert
On: Invert left and right frame contents.
Off: Default frame contents.
Video/Audio
Frequency
Adjust the timing of the projector relative to the computer.
Note
This functions is only supported under computer mode.
Tracking
Adjust the phase of the projector relative to the computer.
Note
This functions is only supported under computer mode.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Zoom
Using the remote control
1. Press Magnify on the remote control to display the Zoom bar.
2. Press / to magnify the picture to a desired size.
3. Press Enter on the remote control to switch to the paning mode and press the
directional arrows to navigate the picture. The zoom bar needed to be shown on
screen if we want to switch the paning mode.
4. To reduce size of the picture, press Magnify and press repeatedly until it is
restored to the original size.
Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
until the Video/Audio menu is highlighted.
2. Press to highlight Zoom.
3. Repeat steps 2-4 in the section of Using the remote control above.
Video Setting
Allow you to enter the Video Setting menu.
Sharpness: Sharpen or soften the image.
29
Tint: Shift colors toward red or green.
Saturation: Adjust a video image from black and white to fully saturated color.
Audio Setting
Allow you to enter the Audio Setting menu.
Volume: Adjust the projector’s volume level.
Mute: Toggles the projector audio between on and off.
Setting
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Menu Setting
Allow you to enter the Menu Setting menu.
Menu Position: Choose the menu location on the display screen.
Menu Display Time: Duration of OSD menu display countly starts (at idle state by
second).
OSD Transparency: Select to change the transparency level of the OSD
background.
HDMI Format
Selects appropriate HDMI format automatically or manually.
Note
This function is only available when the HDMI-input port is in use.
HDMI is only for PJD5234.
HDMI Range
Enhanced: The range for HDMI output signal is from 0 - 255.
Normal: The range for HDMI output signal is from 16 - 235.
Note
HDMI is only for PJD5234.
Blank Screen
To select the screen color when Blank function is active.
Start up Screen
Allows you to select which logo screen will display during projector start-up. Three
options are available: ViewSonic logo, Black screen, or Blue screen.
Message
Enable or disable the message box at the right bottom of the screen.
Auto Source
Automatically scan through all the input source if the function in the OSD menu is On.
The function will stop the signal auto scan process and fix the signal source you
preferred if you turn Off the Auto Source.
Auto Power Off
30
Allows the projector to turn off automatically if no input signal is detected after a set
period of time.
Sleep Timer
No matter whether the projector detect signal or not, the projector will turn off
automatically when the countdown has finished.
Standby Setting
Green Mode: Enable this function when power consumption is under 0.5W.
Note
When Green Mode is “On”, Active VGA Out and Active audio out will be gray out.
Active VGA Out: Set whether the VGA OUT function works when the projector is in
standby (powered off but connected to AC power).
Active audio out: Set whether the audio out function works when the projector is in
standby (powered off but connected to AC power).
Quick Power Off
On: The projector will directly shut down without cooling procedure.
Off: The projector will shut down following normal cooling procedure.
Smart Restart: Selecting On enables you to restart the projector immediately within
3 minutes after turning it off. After 3 minutes, if the projector is not turned on again,
it will directly enter the standby mode.
Option
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or OFF.
Password
Set, change or delete the password. When the password function is added, image
projection will require to input the preset password when turning on the projector.
Presentation Timer
Remind the presenter to finish the presentation within a certain time frame.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
Lamp Setting
Allow you to enter the Lamp Setting menu.
Lamp Hours: Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset: Reset the lamp Hour to 0 hours.
Eco Mode: Use this function to dim the projector lamp light output which will lower
power consumption and increase lamp life.
Dynamic Eco Timer (RC): Sets the timer of triggering Dynamic Eco function. The
projector lamp will start dimming when the timer period has finished.
31
My Button
Allow user to define a short cut key on the remote control, and the function item is
selected in OSD menu.
Pattern
Display embedded test pattern.
Factory Default
Restore settings to factory default.
Note
The following settings will still remain: Keystone, Password, Projection, High Altitude
and Language.
Language
Select the language used by the on-screen menu.
Information
Input Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal frequency.
V. Frequency
Display current image vertical frequency.
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
32
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages inside the
projector can cause severe injury. Do not attempt to service this product yourself. Refer
all servicing to qualified service personnel.
Cleaning the lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the projector housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Note
Turn off the projector and remove the AC power cord from the power outlet before
beginning maintenance work.
Make sure the lens is cool before cleaning.
Do not use detergents or chemicals other than those noted above. Do not use benzene
or thinners.
Do not use chemical sprays.
Use a soft cloth or lens paper only.
33
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
Note
The lamp is extremely hot right after turning off the projector. If you touch the lamp, you
may scald your finger. When you replace the lamp, wait for at least 45 minutes for the
lamp to cool down.
Do not touch the lamp glass at any time. The lamp may explode due to improper
handling, including the touching of the lamp glass.
Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or
terminate their lifetime in a shorter period of time than other similar lamps.
A lamp may explode as a result of vibration, shock or degradation as a result of hours of
use as its lifetime draws to an end. Risk of explosion may differ according to the
environment or conditions in which the projector and lamp are being used.
Wear protective gloves and eyeglasses when fixing or detaching the lamp.
Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
Do not operate the lamp in proximity to paper, cloth, or other combustible material nor
cover it with such materials.
Do not operate the lamp in an atmosphere containing an inflammable substance, such
as thinner.
Thoroughly ventilate the area or the room when operating the lamp in an oxygen
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness,
and other symptoms.
The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the
lamp will be exposed. Leave the area immediately if the lamp shatters while being
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of
mercury fumes. Otherwise it could be harmful to users health.
34
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Option > Lamp Setting” menu.
Note
Dispose the used lamp according to local regulations.
Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
Do not reuse the old lamp. This could cause the lamp to explode.
Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
Do not use the projector with the lamp cover removed.
35
Specifications
Display system Single 0.55" DLP panel
Resolution XGA (1024 x 768 pixels)
Zoom 1.1x
F/No. 1.97 - 2.17
Focal length 21.95 - 24.18mm
Screen size 30” - 300”
Lamp 190W (PJD5232 / PJD5234)
280W (PJD7223)
Input terminal D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal
input (3.5 mm stereo mini jack) x 2, HDMI x 1 (only for
PJD5234)
Output terminal D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo
mini jack) x 1
Control terminal RS-232 x 1, Type B USB x1 (supports firmware
upgrade and remote mouse control)
Speaker 2 watt x 1
Video compatibility NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p),
Composite video
Scanning frequency
Horizontal frequency
Vertical frequency
31 - 100 KHz
24 - 120 Hz
Environment Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity:30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 2.6A
Power consumption 255W (Max.) PJD5232 & PJD5234
360W (Max.) PJD7223
Dimension (W x D x H) 294 x 219 x 113 mm
Weight 2.1 kg (4.6 lb)
Note: Design and Specifications are subject to change without prior notice.
36
Dimensions
294 mm (W) x 219 mm (D) x 113 mm (H)
Ceiling mount installation
219
113
294
85
72
150
32
40
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
37
Appendix
LED Indicator Messages
LED Type Color Status Meaning
Power LED Blue Solid Standby mode when green mode is turned
on.
Tem p LED R e d O ff
Lamp LED Red Off
Power LED Blue Flash Standby mode when green mode is turned
off.
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Flash Powering up
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid Normal operation
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid Powering down
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid If the projector system has some problems
with its fans, the projector will shut down.
Temp LED Red Flash
Lamp LED Red Flash
Power LED Blue Solid The lamp has reached its end of life and
must be changed soon. The lamp will
continue to operate until it fails. Change the
lamp. If the lamp is off, then the ballast will
become malfunction.
Temp LED Red Off
Lamp LED Red Flash
Power LED Blue Flash 1. Temperature is too high. The lamp will
turn off. The fan motor is cooling the lamp.
Or
2. The cooling process is not complete after
the projector is shut down and re-started
right away.
Temp LED Red Flash
Lamp LED Red Off
Power LED Blue Flash The lamp ignition failed. If temperature is
too high, the fans will cool the lamp.
Temp LED Red Off
Lamp LED Red Solid
38
Compatibility Modes
Computer:
Video:
Resolution H-Sync [KHz] V-Sync [Hz]
640 x 350 37.9 85.0
640 x 480 24.6 50.0
31.5 59.9
37.9 72.8
37.5 75.0
43.3 85.0
61.9 120.0
720 x 400 31.5 70.0
37.9 85.0
800 x 600 31.0 50.0
35.2 56.0
37.9 60.3
48.1 72.0
46.9 75.0
53.7 85.1
76.3 120.0
1024 x 768 48.4 60.0
56.5 70.1
60.0 75.0
68.7 85.0
97.6 120.0
1152 x 864 67.5 75.0
1280 x 768 47.8 60.0
1280 x 960 60.0 60.0
85.9 85.0
1280 x 1024 64.0 60.0
1400 x 1050 65.3 60.0
1600 x 1200 75.0 60.0
1680 x 1050 65.3 60,0
640x480@67Hz 35.0 66.7
832x624@75Hz 49.7 74.6
1152x864@75Hz 68.7 75.1
Compatibility Resolution H-Sync [KHz] V-Sync [Hz]
480i 720 x 480 15.8 60
480p 720 x 480 31.5 60
576i 720 x 576 15.8 50
576p 720 x 576 31.3 50
720p 1280 x 720 37.5 50
720p 1280 x 720 45 60
1080i 1920 x 1080 33.8 60
1080i 1920 x 1080 28.1 50
1080p 1920 x 1080 67.5 60
1080p 1920 x 1080 56.3 50
39
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
Be sure that the power cord is securely connected to the projector and the other end
is
plugged into an outlet with power.
Press the power button again.
Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
Press
SOURCE
on the projector or
Source
on the remote control
to select an active
input source.
Be sure the external source is turned on and connected.
For a computer connection, ensure your notebook computers external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
Press
MENU/EXIT
on the projector or
Menu
on the remote control
, go to Video/Audio
and adjust Frequency or Tracking.
Remote control problems
If the remote control does not operate:
Be sure nothing is blocking the remote control receiver on the front of the projector.
Use the remote control within the effective range.
Aim the remote control at the screen or at the front of the projector.
Move the remote control so it is more directly in front of the projector and
not as far to
the side.
40
RS-232 Command and Configuration
!!!!!!!!!
D-Sub 9 pin
11 CD
2RXD
3TXD
4DTR
5GND
6DSR
7RTS
8CTS
9RI
Baud Rate 19200 bps
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
Wire List
C1 COLOR C2
1 Black 1
2Brown 3
3Red 2
4 Orange 6
5 Yellow 5
6Green 4
7Blue 8
8Purple 7
9White 9
SHELL DW SHELL
41
Function Action Control Code
Power
Power on BE,EF,10,05,00,C6,FF,11,11,01,00,01,00
Power off BE,EF,03,06,00,DC,DB,69,00,00,00,00,00
Source input
Computer1 BE,EF,03,19,00,19,29,01,47,02,CC,CC,00
Computer2 BE,EF,03,19,1E,90,72,01,47,02,CC,CC,00
S-Video BE,EF,03,19,00,E8,69,01,47,02,CC,CC,00
Video BE,EF,03,19,00,78,A8,01,47,02,CC,CC,00
HDMI BE,EF,03,19,00,DA,2B,01,47,02,CC,CC,00
Projector position
Front table BE,EF,10,07,9F,9D,0E,0A,EF,00,00,00,00
Rear table BE,EF,10,07,9F,9D,0E,0A,EF,01,00,00,01
Front ceiling BE,EF,10,07,9F,9D,0E,0A,EF,02,00,00,02
Rear ceiling BE,EF,10,07,9F,9D,0E,0A,EF,03,00,00,03
OSD
Menu BE,EF,02,06,00,E9,D3,30,00,00,00,00,00
Up BE,EF,02,06,00,6D,D2,34,00,00,00,00,00
Down BE,EF,02,06,00,0B,D2,32,00,00,00,00,00
Left BE,EF,02,06,00,DA,D3,33,00,00,00,00,00
Right BE,EF,02,06,00,38,D2,31,00,00,00,00,00
Lamp
ECO on BE,EF,03,06,00,EF,DB,6A,00,00,00,00,00
ECO off BE,EF,03,06,00,3E,DA,6B,00,00,00,00,00
Using hours BE,EF,03,06,00,BA,DB,6F,00,00,00,00,00
Fan
High Attitude on BE,EF,02,06,00,40,D3,80,00,00,00,00,01
High Attitude off BE,EF,02,06,00,40,D3,80,00,00,00,00,00
Keystone
Keystone up BE,EF,03,06,00,10,DB,65,00,00,00,00,00
Keystone down BE,EF,03,06,00,23,DB,66,00,00,00,00,00
Aspect ratio
4:3 BE,EF,03,06,00,0D,DA,68,00,01,00,00,01
16:9 BE,EF,03,06,00,0D,DA,68,00,02,00,00,02
Anamorphic BE,EF,03,06,00,0D,DA,68,00,02,00,00,04
Auto BE,EF,03,06,00,0D,DA,68,00,02,00,00,00
Blank
Blank on BE,EF,02,06,00,DF,DF,66,00,01,00,00,01
Blank off BE,EF,02,06,00,DF,DF,66,00,02,00,00,02
Freeze
Freeze on BE,EF,02,06,00,02,D0,2B,00,01,00,00,01
Freeze off BE,EF,02,06,00,02,D0,2B,00,02,00,00,02
Volume
Volume + BE,EF,02,06,00,F1,DE,68,00,00,00,00,00
Volume - BE,EF,02,06,00,20,DF,69,00,00,00,00,00
Mute on BE,EF,02,06,00,0E,DE,67,00,01,00,00,01
Mute off BE,EF,02,06,00,0E,DE,67,00,02,00,00,02
Auto source
Auto source on BE,EF,03,06,00,89,DB,6C,00,00,00,00,00
Auto source off BE,EF,03,06,00,58,DA,6D,00,00,00,00,00
Auto Sync BE,EF,02,06,00,86,D1,2F,00,00,00,00,00
Factory default BE,EF,03,06,00,6B,DA,6E,00,00,00,00,00
Firmware version BE,EF,03,06,00,D5,D9,70,00,00,00,00,00
System Status BE,EF,03,06,00,04,D8,71,00,00,00,00,00
3D Sync
3D Sync on BE,EF,02,06,00,54,EF,7C,00,01,00,00,01
3D Sync off BE,EF,02,06,00,54,EF,7C,00,00,00,00,00
Top-Bottom BE,EF,02,06,00,54,EF,7C,00,01,00,00,02
Frame Sequential BE,EF,02,06,00,54,EF,7C,00,01,00,00,03
Frame Packing BE,EF,02,06,00,54,EF,7C,00,01,00,00,04
Side-By-Side BE,EF,02,06,00,54,EF,7C,00,01,00,00,05
42
Color mode
Brightest BE,EF,03,06,00,38,5A,88,12,08,08,12,08
PC BE,EF,03,06,00,38,5A,88,10,00,00,10,00
Movie BE,EF,03,06,00,38,5A,88,13,01,01,13,01
ViewMatch BE,EF,03,06,00,38,5A,88,14,02,02,14,02
White Board BE,EF,03,06,00,38,5A,88,15,05,05,15,05
Black Board BE,EF,03,06,00,38,5A,88,16,06,06,16,06
Green Board BE,EF,03,06,00,38,5A,88,17,07,07,17,07
User 1 BE,EF,03,06,00,38,5A,88,18,03,03,18,03
User 2 BE,EF,03,06,00,38,5A,88,19,04,04,19,04
Language
English BE,EF,1A,0C,00,09,0B,3A,00,01,00,00,01
Nederlands BE,EF,1A,0C,00,09,0B,3A,00,02,00,00,02
BE,EF,1A,0C,00,09,0B,3A,00,03,00,00,03
BE,EF,1A,0C,00,09,0B,3A,00,04,00,00,04
Italiano BE,EF,1A,0C,00,09,0B,3A,00,05,00,00,05
BE,EF,1A,0C,00,09,0B,3A,00,06,00,00,06
BE,EF,1A,0C,00,09,0B,3A,00,07,00,00,07
BE,EF,1A,0C,00,09,0B,3A,00,08,00,00,08
BE,EF,1A,0C,00,09,0B,3A,00,09,00,00,09
BE,EF,1A,0C,00,09,0B,3A,00,0A,00,00,0A
BE,EF,1A,0C,00,09,0B,3A,00,0B,00,00,0B
BE,EF,1A,0C,00,09,0B,3A,00,0C,00,00,0C
Deutsch BE,EF,1A,0C,00,09,0B,3A,00,0D,00,00,0D
Svenska BE,EF,1A,0C,00,09,0B,3A,00,0E,00,00,0E
BE,EF,1A,0C,00,09,0B,3A,00,0F,00,00,0F
Suomi BE,EF,1A,0C,00,09,0B,3A,00,10,00,00,10
Polski BE,EF,1A,0C,00,09,0B,3A,00,11,00,00,11
Indonesia BE,EF,1A,0C,00,09,0B,3A,00,12,00,00,12
BE,EF,1A,0C,00,09,0B,3A,00,13,00,00,13
BE,EF,1A,0C,00,09,0B,3A,00,14,00,00,14
Magnify
Magnify Inc BE,EF,02,06,00,22,55,76,00,00,00,00,01
Magnify Dec BE,EF,02,06,00,22,55,76,00,00,00,00,00
Green Mode
Green Mode On BE,EF,02,06,00,40,B5,86,00,00,00,00,01
Green Mode Off BE,EF,02,06,00,40,B5,86,00,00,00,00,00
Dynamic Mode
Dynamic Mode On BE,EF,02,06,00,D3,D1,2A,00,00,00,00,01
Dynamic Mode Off BE,EF,03,06,00,EE,DA,6B,00,00,00,00,01
Quick Power Off
QuickPowerOff_On BE,EF,10,05,00,C6,FF,11,11,01,00,01,01
QuickPowerOff_Off BE,EF,03,06,00,DC,DB,69,69,00,00,69,00
43
IR Control Table
System Code: 83F4
Format : NEC
17
08
41
45
52
40 10
0b
0e
0f
0c
30
56
28
36
37
06
05
31
18
82
8E
03
83
55
2B
07
27
14
13
15
44
Key Format Byte1 Byte2 Byte3 Byte4
Power NEC 83 F4 17 E8
Auto Sync NEC 83 F4 08 f7
VGA1 NEC 83 F4 41 be
VGA2 NEC 83 F4 45 ba
Video NEC 83 F4 52 ad
Source NEC 83 F4 40 bf
Color Mode NEC 83 F4 10 ef
Enter NEC 83 F4 15 ea
Up / Keystne+ NEC 83 F4 0b f4
Down / Keystone- NEC 83 F4 0c f3
Left NEC 83 F4 0e f1
Right NEC 83 F4 0f f0
Menu NEC 83 F4 30 CF
My Button(Function) NEC 83 F4 56 A9
Exit NEC 83 F4 28 D7
Mouse NEC 83 F4 31 CE
Mouse left NEC 83 F4 36 C9
Mouse right NEC 83 F4 37 C8
Mouse Page Up NEC 83 F4 06 F9
Mouse Page Down NEC 83 F4 05 FA
Lock(Key pad) NEC 83 F4 8E 71
Pattern NEC 83 F4 55 AA
D.Eco
(Dynamic Eco)
NEC 83 F4 2B D4
Magnify + NEC 83 F4 18 e7
Freeze NEC 83 F4 03 fc
Blank NEC 83 F4 07 f8
Timer (Presentation) NEC 83 F4 27 d8
Volume+ NEC 83 F4 82 7D
Volume- NEC 83 F4 83 7C
Mute NEC 83 F4 14 eb
Aspect NEC 83 F4 13 EC
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
Country/Region Website
T = Telephone
F = FAX
Email
Australia/New Zealand www.viewsonic.com.au
AUS= 1800 880 818
NZ= 0800 008 822
service@au.viewsonic.com
Canada www.viewsonic.com
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
service.ca@viewsonic.com
Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com
India www.in.viewsonic.com T= 1800 266 0101 service@in.viewsonic.com
Korea www.kr.viewsonic.com T= 080 333 2131 service@kr.viewsonic.com
Latin America (Argentina) www.viewsonic.com/la/ T= 0800-4441185 soporte@viewsonic.com
Latin America (Chile) www.viewsonic.com/la/ T= 1230-020-7975 soporte@viewsonic.com
Latin America
(Columbia)
www.viewsonic.com/la/ T= 01800-9-157235 soporte@viewsonic.com
Latin America (Mexico) www.viewsonic.com/la/ T= 001-8882328722 soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru) www.viewsonic.com/la/ T= 0800-54565 soporte@viewsonic.com
Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com
Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com
Puerto Rico & Virgin
Islands
www.viewsonic.com
T= 1-800-688-6688 (English)
T= 1-866-379-1304 (Spanish)
F= 1-909-468-3757
service.us@viewsonic.com
soporte@viewsonic.com
Singapore/Malaysia/
Thailand
www.viewsonic.com.sg T= 65 6461 6044 service@sg.viewsonic.com
South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com
United States www.viewsonic.com
T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530
F= 1-909-468-3757
service.us@viewsonic.com
45
Limited Warranty
ViewSonic
®
Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years
IRUODERUDQGRQH\HDUIRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHU
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the
RULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH(XURSH2QH\HDU
warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days
IRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH
Other regions or countries: Please check with your local dealer or local ViewSonic
RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWR
manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration, failure, or malfunction resulting from:
D$FFLGHQWDEXVHPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUH
LPSURSHUPDLQWHQDQFHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQRUIDLOXUHWRIROORZ
instructions supplied with the product.
E2SHUDWLRQRXWVLGHRISURGXFWVSHFL¿FDWLRQV
c. Operation of the product for other than the normal intended use or not under
normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
J&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFSRZHUÀXFWXDWLRQVRUIDLOXUH
K8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
46
How to get service:
1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description
FRQWDLQHGKHUHLQLQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUD
particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
XSRQLQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRI
business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWV
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
47
Mexico Limited Warranty
ViewSonic
®
Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of
WKH¿UVWFRQVXPHUSXUFKDVH
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWRPDQXIDFWXUHU¶V
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
 $Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration or malfunction resulting from:
D$FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFW
PRGL¿FDWLRQXQDXWKRUL]HGDWWHPSWHGUHSDLURUIDLOXUHWRIROORZLQVWUXFWLRQVVXSSOLHGZLWKWKH
product.
b. Any damage of the product due to shipment.
F&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFDOSRZHUÀXFWXDWLRQVRUIDLOXUH
G8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
e.Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service
center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
LQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
LQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVVRSSRUWXQLW\
loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
48
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within
Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA
de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de
C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av.
Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
7HO(QJOLVK
6SDQLVK
Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
49
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Viewsonic PJD5232 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Viewsonic PJD5232 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Viewsonic PJD5232

Viewsonic PJD5232 Gebruiksaanwijzing - Deutsch - 55 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info