785493
26
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
24 Manual Skylla with universal input
5. FAULT TRACING
When a fault occurs in the battery charger, the following table can be used in order
to find the fault. Before the Skylla is being checked, make sure that all the devices
connected to the battery charger are removed. If the fault can not be solved, please
contact your Victron Energy dealer.
Problem
Possible cause
Solution
The charger does
not operate
The mains voltage has to be in
between 90Vac and 265 Vac.
Measure the mains voltage and make sure
it is in between 90Vac and 265Vac.
A broken input fuse.
Return the charger to your dealer.
The battery is not
being fully charged
The equalize-charge mode is set to
a too short period.
Set the equalize-charge mode to a longer
time.
A bad battery connection.
Check the battery connections.
The boost charge voltage is
set to a wrong value.
Adjust the boost charge voltage to the
right value.
The float charge voltage is
set to a wrong value.
Adjust the float charge voltage to the right
value.
The capacity of the battery is too
large.
Connect a battery with a smaller capacity
or install a larger charger.
The output fuses are broken.
Replace the output fuses.
The battery is
being overcharged
The battery charger is set into the
permanent boost-charge mode.
Deselect the permanent boost DIP-switch
(Rboost).
The boost charge voltage is
set to a wrong value.
Adjust the boost charge voltage to the
right value.
The float charge voltage is
set to a wrong value.
Adjust the float charge voltage to right
value.
A bad battery.
Check the battery.
The battery is located in a warm
place
Connect a temperature sensor
The battery is too small.
Reduce the charge current.
The failure led
illuminates
The charger is switched off as a
result of a high ambient
temperature.
Place the charger in a cooler, or better
ventilated place.
The failure led
flashes
The charger is reducing the output
current as a result of a high
ambient temperature.
Place the charger in a cooler, or better
ventilated place.
The failure led
flashes in a code
1
The output fuses are broken.
Replace the output fuses.
The failure led
illuminates in
combination with a
blinking on/off led
There is a voltage drop higher than
2V across the battery cables.
Turn the charger off, replace battery cables
and connect them well.
1
Flashing code sequence is two times on in one second and then one second off.
A qualified technician may only remove the cover of the Skylla.
Before obtaining access to the Skylla the mains supply circuit
must be disconnected.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Skylla-TG 24 50 (1 1) bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Skylla-TG 24 50 (1 1) in de taal/talen: Engels als bijlage per email.

De handleiding is 0.47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info