785490
8
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
7
victron energy
Adjustments without remote panel
WARNING: Always check with your battery
supplier if the choosen charge characteristic is
suitable for your battery and application
Remove the frontplate and disconnect battery
and Voltage sense and Temperature sense and
connect a digital voltmeter to – and +1 output.
Bulk-current
While switching on keep both the pushbuttons
&
pushed.
Release pushbuttons.
Bulk LED is flashing alternately with Failure LED.
Push
for up and
for down.
Reading as follows:
Discard first digit of DVM then multiply by 10, i.e:
22.50V => ….2.50 => 25 Amps
15.00V => .....5.00 => 50 Amps
Switch the charger Off to store.
Absorption and Float voltage
While switching on keep the pushbutton
pushed for Absorption voltage and
for Float-
voltage.
Release pushbuttons.
Absorption or Float LED is flashing alternately
with Failure LED.
Push
for up and
for down.
Reading on voltmeter as is.
Switch the charger Off to store.
Please note that in adjust-mode the
Temperature sense compensation is not taken
into account.
Warning: If the charger is not switched Off
after an adjustment the new value will not be
stored but will remain on the outputs. After 4
hours the charger continues the normal
sequence with the old values. This can be
useful if a forced high voltage is wanted to get
some life in an assumed ‘dead’ battery.
Return to factory settings
Switch the charger on.
Keep the pushbutton
and/ or
pushed while
switching off.
The factory settings are restored.
When ready
Connect battery and if applicable Voltage sense
and Temperature sense.
Replace the frontplate.
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Adjusting maximum Bulk current
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Adjusting Float voltage
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Adjusting Absorption voltage
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Restoring defaults
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Phoenix acculader 24 16 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Phoenix acculader 24 16 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info