785222
29
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
9. Battery monitor settings
This chapter explains all battery monitor settings. In addition to this we also have a video available explaining these settings and
how the interact with each other to achieve accurate battery monitoring for both lead-acid and lithium batteries.
https://www.youtube.com/embed/mEN15Z_S4kE
9.1. Special note on the Lynx Smart BMS battery monitor settings
Unlike other battery monitors, the Lynx Smart BMS battery monitor settings are mostly fixed settings and are not customizable.
The reason for this is that the Lynx Smart BMS is always used together with Victron Energy Smart Lithium batteries and a lot of
battery monitor parameters are therefore known because they relate to the battery type.
To give an overview of the status of each battery setting:
These battery monitor settings are adjustable:
Battery capacity: by default set at 200Ah, needs to be set on first install.
Charged Voltage: by default set at 14.0V (12V system), 28.0V (24V system) and 56.0V (48V system).
Tail current: by default set at 4% (as a fraction of the battery capacity).
Charged detection time: by default set at 3 minutes.
These battery monitor settings are automatic settings:
Zero current calibration: Is done automatically each time at power up.
These battery monitor settings are fixed:
Peukert exponent: 1.05
Charge efficiency factor: 99%
Current threshold: 0.1A
Discharge floor: 15%
Delta T: 1
SOC cycle end: 90%
SOC Cycle: 65%
SOC full discharge: 5%
The meaning of each battery monitor parameter is explained in next chapter.
9.2. Battery capacity
This parameter is used to tell the battery monitor how big the battery is. This setting should already have been done during the
initial installation.
The setting is the battery capacity in Amp hours (Ah).
Default setting Range Step size
200 Ah 1 - 9999 Ah 1 Ah
9.3. Charged voltage
The battery voltage must be above this voltage level to consider the battery as fully charged. As soon as the battery monitor
detects that the voltage of the battery has reached the “charged voltage” and the current has dropped below the “tail current” for a
certain amount of time, the battery monitor will set the state of charge to 100%.
Default setting Range Step size
14.0V (12V system)
28.0V (24V system)
56.0V (48V system)
0 - 60V 0.1V
The “charged voltage” parameter should be set to 0.2V or 0.3V below the float voltage of the charger.
Lynx Smart BMS
Page 26 Battery monitor settings
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Lynx Smart BMS 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Lynx Smart BMS 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info