785222
21
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
The operation state of the Alarm relay can be set to continuous or intermittent operation. In intermittent operation the relay
switches on and off every 0.8 seconds.
DVCC settings
The discharge current limit at pre-alarm setting is set by default set to "no". This can be changed to "yes".
The absorption time is set by default to 2hours. This can be adjusted if required.
The state of charge (SoC) threshold is set by default to 70%. This is the threshold at which the Lynx Smart BMS starts a new
full charging cycle. This can be adjusted if required.
The repeated absorption time in days at which a new full charging cycle is started if the battery state of charge does not fall
below the SoC threshold. The default is every 30 days and can be adjusted if required.
Battery Monitor settings
The charged voltage is the voltage at above which the battery monitor synchronises and resets the state of charge to 100%.
For synchronisation to happen, the tail current and charged detection time conditions need to have been met as well. The
default is set to 14.0V and can be adjusted if required.
The tail current is the current at below which the battery monitor synchronises and resets the state of charge to 100%. For
synchronisation to happen, the charged voltage and charge detection time conditions need to have been met as well. The
default is set to 4.00% and can be adjusted if required.
The charged detection time is the time passed after which the battery monitor synchronises and resets the state of charge to
100%. For synchronisation to happen, the charged voltage and charged current conditions need to have been met as well. The
default is set to 3 minutes and can be adjusted if required.
VictronConnect setting Lynx Smart BMS
6.3.4. Settings Lynx Distributor
These instructions only apply if the system contains a Lynx Smart BMS.
Use the VictronConnect App to give each fuse a custom name (maximum 16 characters). If the fuse name is empty (0
characters), the fuse will be disabled from monitoring and be ignored.
Navigate to the settings page by clicking the gear symbol at the top right-hand corner.
On the settings page scroll down to the Lynx Distributor settings.
Click on a fuse name and a window opens to rename the fuse.
Lynx Smart BMS
Page 18 Installation
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Lynx Smart BMS 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Lynx Smart BMS 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info