785549
10
Verklein
Vergroot
Pagina terug
1/150
Pagina verder
6
3.3.3 Activating equalisation or forced absorption
The EasyPlus can be put into both these states from the remote panel as well as with the front panel
switch, provided that all switches (front, remote and panel) are set to onand no switches are set to
charger only’.
In order to put the EasyPlus in this state, the procedure below should be followed.
If the switch is not in the required position after following this procedure, it can be switched over
quickly once. This will not change the charging state.
NOTE: Switching from onto charger onlyand vice versa, as described below, must be done quickly. The switch
must be toggled such that the intermediate position is 'skipped', as it were. If the switch remains in the off
position even for a short time, the device may be turned off. In that case, the procedure must be restarted at step
1. A certain degree of familiarisation is required when using the front switch on the EasyPlus in particular. When
using the remote panel, this is less critical.
Procedure:
1. Check whether all switches (i.e. front switch, remote switch or remote panel switch if present) are
in the onposition.
2. Activating equalisation or forced absorption is only meaningful if the normal charging cycle is
completed (charger is in 'Float').
3. To activate:
a. Switch rapidly from onto charger only’ and leave the switch in this position for ½ to 2 seconds.
b. Switch rapidly back from charger onlyto onand leave the switch in this position for ½ to 2
seconds.
c. Switch once more rapidly from onto charger onlyand leave the switch in this position.
4. On the EasyPlus the three LEDs Inverter, ‘Chargerand Alarmwill now flash 5 times.
If a MultiControl panel is connected, on the panel the LEDs bulk, ‘absorptionand floatwill also
flash 5 times.
5. Subsequently, on the EasyPlus the LEDs Bulk, ‘Absorptionand Floatwill each light during 2
seconds.
If a MultiControl panel is connected, on the panel the LEDs bulk, ‘absorptionand floatwill also
each light during 2 seconds.
6.
a. If the switch on the EasyPlus is set to onwhile the BulkLED lights, the charger will switch to
equalisation.
Similarly, if the switch on the MultiControl panel is set to onwhile the BulkLED lights, the charger
will switch to equalisation.
b. If the switch on the EasyPlus is set to onwhile the AbsorptionLED lights, the charger will switch
to forced absorption.
Similarly, if the switch on the MultiControl panel is set to onwhile the AbsorptionLED lights, the
charger will switch to forced absorption.
c. If the switch on the EasyPlus is set to onafter the three LED sequence has finished, the charger
will switch to Float’.
Similarly, if the switch on the MultiControl panel is set to onafter the three LED sequence has
finished, the charger will switch to float’.
d. If the switch has not been moved, the EasyPlus will remain in ‘charger only’ mode and switch to
‘Float’.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron EasyPlus 12 1600 70-16 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron EasyPlus 12 1600 70-16 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1.44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info