785208
13
Verklein
Vergroot
Pagina terug
1/71
Pagina verder
10
6.2 Setting the scaling factor
Configuration of the scaling factor is only needed for non VE.Bus Multis. (All Multi firmware
versions 15xxyyy, 17xxyyy and 18xxyyy)
The scaling factor is used to match the currents displayed by the DMC to the currents in the
system.
The scaling factor is calculated using the formula:
Scaling factor = (NrOfDevices * DeviceType) - 1
The DeviceType is 1 for a 16A model Multi and 2 for a 30A model Multi.
NrOfDevices is all the Multis including the master Multi.
Example: You have four 30A Multis. The scaling factor is then: (4 * 2) 1 = 7
Important notes:
1) Do NOT specify the number of slaves (with VEConfigure2) in the Multis when you have
specified a Scaling factor other than zero!
In that case the number of slaves in the Multis must be set to zero!
The system will not work properly if you set the scaling factor in the DMC and the number of
slaves in the Multis!
2) When using a split-phase or 3-phase configuration, the NrOfDevices is determined by the
number of devices in 1 phase. So for a 3-phase system build with 6 Multis the NrOfDevices=2.
6.3 Setting the generator current limit
This parameter needs only to be configured when using an external transfer switch (PowerMan)
(see paragraph 3.1) and is of no influence otherwise.
The generator current limit can be set from 0 to 198 Amps in steps of 2 Amps.
Important note:
Small 3000 rpm generator sets of certain brands will overheat when operating for long periods at
full load. In some cases the maximum current will have to be set at no more than 70 % of the
rated maximum current. The current limit of 1500 rpm generator sets can in general be set at
around 90 % of the rated output current.
6.4 Setting the Upper Shore limits for AC input 1 to 4
To prevent that the operator of the DMC sets a too high current limit for the system an Upper
Shore limit can be set.
Example: You have a system with 5 Multis in parallel. The maximum feed through current would
be 80A. This might be a far too high setting for the circuit breakers used in your system. By
adjusting the “Upper Shore limit” you can prevent that the shore current limit is set higher than, for
instance, 30A.
Four different limits can be set because VE.Bus systems can have up to 4 AC inputs.
For simple VE.Bus systems with Multis or non VE.Bus systems it is sufficient to set only the
“Upper Shore limit for AC input 1”. The others will not be used then.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron Digital Multi Control 200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron Digital Multi Control 200 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0.41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info