813572
12
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
12
WARNING: For delicate floors (for example, parquet), we recommend the placing of a
stable mat or a
suitable carpet below the device. This prevents damage and discolouration to your floor.
OPERATING MODES
The resistance bands (19) can be used in both modes. To use them, slip the safety hooks
through the openings specially designed for them on the back of the platform, as shown
in figure 5. The resistance bands (19) can be used in both modes. To use them, slip
the safety hooks through the openings specially designed for them on the back of the
platform, as shown in figure 5.
Manual mode: Here, the user can set the length and tempo of their exercise, so that it’s tailored to their needs. When using manual
mode, follow these instructions:
1. Plug the VibroShaper into a power socket and press the power switch (3) so that it is in the ON position.
2. Press the “ON” button on the control panel (15) or the button (1) on the remote control.
3. Next, select the length of your exercise. It can be between one and 10 minutes. To increase the number of minutes, press the
button (11) on the control panel or the button on the remote control. To shorten the time, press the button on the control
panel (12) or the button on the remote control. The amount of time left in the exercise appears in the time display (8).
4. Start the exercise by pressing the button (17) on the control panel or the button on the remote control.
5. You can now select the tempo of the vibration. The tempo settings range from 1 to 99. To select your desired tempo setting, press
the button (13) on the control panel or the button on the remote control. To reduce the tempo, press the button (14) on the
control panel or the button on the remote control.
6. You can also select certain tempos quickly using the M button on the remote control. The M button allows you to jump to 90, 60
or 30.
7. To end the exercise at any time, press the button (18) on the control panel or the button on the remote control. Once you’ve
finished the exercise, turn off the device by pressing the button (15) on the control panel or the button (1) on the remote
control.
Chart 1 shows our training recommendations for manual training.
Automatic Mode: The device follows a preset training programme, in which speed and time cannot be altered. When using this
mode the following instructions should be followed:
1. Plug the VibroShaper into a power socket and press the power switch (3) so that it is in the ON position.
2. Press the “ON” button on the control panel (15) or the button on the remote control.
3. There are three different exercise programmes (P1, P2 and P3) available. Press button (16) on the control panel repeatedly or
the button on the remote control repeatedly until the programme you want appears on the programme display (8).
4. Chart 2 shows the exercise tempo of each programme depending on the length.
5. Once you’ve selected your chosen programme, start the exercise by pressing (17) on the control panel or on the
remote control.
6. To stop the device at any time, press the appropriate button (18) on the control panel or the utton on the remote control.
Once you’ve completed the exercise, turn the device off by pressing (15) on the control panel or the utton on the remote
control.
CLEANING AND MAINTENANCE
Before cleaning your VibroShaper, you must make sure that the power switch is in the OFF position and that the cable has
been unplugged from the power socket.
You can use a clean, dry broom or brush to remove dust from the device.
The standing area can be cleaned with a damp cloth.
Do not use corrosive agents to clean the device, because these could damage it.
Clean the remote control with clean cloth.
If the device is not being used for an extended period of time, put it back in its box and store it in a cool, dry place. You
should also take the batteries out of the remote control.
If the device appears to have a defect, follow the instructions in the Troubleshooting section. If the problem persists,
please contact our customer service team.
The safety level of the device can only be maintained if it is regularly checked for damage and wear. If any part of the device
is defective, do not replace it yourself. Please contact our customer service (contact information on the back). Cease using
the device until it has been repaired. In particular, the resistance bands should be checked for wear.
figure 5
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VibroShaper M12156 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VibroShaper M12156 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van VibroShaper M12156

VibroShaper M12156 Aanvulling / aanpassing - Nederlands, Deutsch, English, Français, Italiano - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info