815508
14
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
1414 3-90-30007467Vermont Castings • Stardance SDDVT Installation Manual_R35 • 11/23
B.AssemblingtheStove:
Tools Required
Utility knife
Metal drill bit: size 28 (.140"/3.5mm)
Flat-blade screwdriver
Power drill
Reciprocating saw
9/16" wrench
1/2” Wrench
3/8” Wrench
7/16” Wrench
Parts Bag Contents:
Three (3) Vent Screws
Wood handle w/insert lifter (handle for operable door)
Restrictor Plate
4" Starter pipe
Wireless Remote
Three (3) Hex-head bolts, 1/4"- 20 x 1/2"
One (1) Tube of Vent Gasket Cement
Four (4) CS, Hex Hd 3/8-16 x 1 Gr 2-Z
Four (4) Washer, Fl 3/8-Z
Owner’s Installation and Operating Manual
Unpack Stove
Using the 1/2” wrench remove the (4) lag bolts installed
through the shipping brackets and into the skid. Once the lag
bolts are removed, remove the shipping brackets from each
leg using a 3/8” wrench. These bolts can be discarded after
removal. Install the (4) leg levelers provided in the manual
bag using a 9/16” wrench as needed.
WARNING
Only the IFT appliance is equipped with a three-prong
(grounded) plug for your protection against shock hazard
and should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the ground-
ing prong from this plug.
C.VentingSystemAssembly
CAUTION
All HHT Direct Vent Stoves have been tested and
approved to ANSI/CSA Standards and will operate safely
when installed in accordance with this instruction manual.
Read all instructions before starting installation, then follow
these instructions carefully to maximize stove performance
and safety. Report damaged parts to your dealer.
Important Safety Information
The termination cap MUST be vented directly to the outside.
The termination kit MUST NEVER be connected to a chimney
ue(s) servicing a separate solid-fuel burning appliance or
any other appliances.
Termination cap MUST NOT be recessed into a wall,
Figure 3.1.
The installation must conform with local codes or in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1 (in the United States) or with the current
installation code CSA B149 (in Canada).
WARNING
Always maintain minimum clearances around vent
systems. Rear/Top Vent Vertical Side wall: Horizontal
sections of this vent system require a minimum of 3” (76
mm) clearances to combustibles at the top of the ue and
1” (25 mm) clearance at the sides and bottom until the ue
penetrates the outside wall. A minimum 1” clearance all
around the ue is acceptable at this point of penetration. If
vertical rise is 71⁄2 feet (2.3 m) or higher when top venting,
the clearance to combustibles is 1” on all sides of the
horizontal run. FOR VERTICAL RUNS ONLY, maintain a
1” (25 mm) minimum clearance to all sides. Do not pack
the open air spaces around the stove or ue with insulation
or other materials. Any horizontal run must have a 1/4” rise
for every one (1) foot of run towards the vent termination.
Never run the vent level or down.
WARNING
Failure to follow these instructions may create a possible
re hazard and will void the warranty.
WARNING
Any common venting of this gas appliance with other gas
appliances is not allowed.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vermont Castings Stardance Series bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vermont Castings Stardance Series in de taal/talen: Engels als bijlage per email.

De handleiding is 7.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Vermont Castings Stardance Series

Vermont Castings Stardance Series Gebruiksaanwijzing - Français - 54 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info