622813
3
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
The 3D printer contains a lot of moving parts, but the force of the stepper motors is too low to cause serious injuries. Never-
theless it is recommended to provide additional protection against mechanical risks.
The easiest way to make your 3D printer “accident proof” is to put it inside a protective enclosure which completely covers
the 3D printer – with or without an access door and fume extraction. (numerous designs can be found on the internet)
To make it extra safe a switch which interrupts the power supply of the printer when the enclosure or door is opened can be
added. It is also advisable to install an external emergency stop switch, which also cuts off the power supply.
Providing adequate protection is the responsibility of the assembler.
Always cut power before maintenance or modication.
Mechanical safety and protection:
!
The 3D printer is not intended for use by persons (including children) with reduced physical, or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of
the appliance by a person responsible for their safety
Children should be supervised to ensure that they do not play with the appliance.
The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide.
The information in this document was obtained from sources which we believe are reliable.
However, the information is provided without any warranty, express or implied, regarding its correctness.
The conditions or methods used for assembling, handing, storage, use or disposal of the device are beyond our control and
may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability
for loss, injuries, damage, or expense arising out of or in any way connected with the assembly, handling, storage, use or
disposal of the product.
General safety information:
There is a potential risk of burns as the Printer head (extruder) can reach up to 270°C.
The use of common sense should be sufcient to prevent burns, but in some environments it is highly recommended to
provide additional protection. (see § Mechanical safety and protection)
The max. temperature of the heated bed is 60°C, this is below the 1 min. burn threshold for plastic surfaces according to
CENELEC Guide 29. Normal reexes prevent long contact periods with hot surfaces
Always let the 3D printer cool down for 60 min. before maintenance or modication.
Risk of burns:
!
This printer is designed for use with PLA and ABS lament (MSDS for the Velleman lament is available).
PLA: is a safe and non-toxic material, there are no known health safety risks when used in 3D printers.
ABS: when printing with ABS there is a distinctive ‘burned plastic’ smell. This is quite normal but it may also cause head-
aches, respiratory- and eye irritation with sensitive people (although it is not toxic)
Only use the printer in a well-ventilated area, if printing with ABS it is advisable to add a fume hood (with active car-
bon ltering for ductless extraction). Fume extraction is mandatory for use in ofces, classrooms and alike.
Never burn printer lament, toxic gasses and vapors will be generated if exposed to re.
Health:
!
- 3 -- 2 -
������������������ ��������������������
3

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Velleman-K8200

Zoeken resetten

  • na update van de firmware VERGEET NIET OM UW EEPROM-INSTELLINGEN OPNIEUW IN TE STELLEN NA DE UPGRADE! wat wordt daarmee bedoeld? Gesteld op 2-1-2022 om 12:29

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velleman K8200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velleman K8200 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Velleman K8200

Velleman K8200 Installatiehandleiding - Nederlands - 3 pagina's

Velleman K8200 Gebruiksaanwijzing - Nederlands - 2 pagina's

Velleman K8200 Installatiehandleiding - Deutsch - 664 pagina's

Velleman K8200 Gebruiksaanwijzing - English - 25 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info