622292
11
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
DVM4200
24.06.2015 ©Velleman nv
11
7.1 Voltage measurements
Do not measure circuits where voltages > 600V CAT IV or > 1000V
CAT III may reside.
Always be careful when working with voltages above 60Vdc or 30Vac rms.
Keep your fingers behind the probe barriers at all times during
measurement. Do not touch unused terminals when the meter is linked to a
circuit which is being tested.
Connect the red test lead to the "VΩ " jack and the black lead to the "COM"
jack.
Set the rotary switch to V
Press the SELECT button to choose between AC or DC measurement.
Press the RANGE button to manually select the range.
Connect the test probes to the source being measured.
The measured value appears on the LCD display.
Notes:
For DC-measurements, when a negative polarity is present at the red test lead,
the indicated value is preceded by a “-” sign.
When measuring DC offset of an AC voltage, measure the AC voltage first and
select a range for the DC offset equal to or higher than the AC range to increase
accuracy.
7.2 Resistance measurements
Do not perform resistance measurements on live circuits.
Connect the red test lead to the "VΩ " jack and the black lead to the "COM"
jack.
Set the rotary switch to " . When necessary, press the SELECT button until
is shown on the display.
Press the RANGE button to manually select the range.
Connect the test probes to the source being measured.
The measured value appears on the LCD display.
Notes:
o Never perform resistance measurements on a live circuit and make sure all
capacitors are completely depleted.
o To increase accuracy when measuring low resistance values, first hold the tips
of the measuring probes together to determine the resistance value of the test
leads. Subtract this value from the measured value of the circuit.
o For resistance measurements above 10MΩ the meter needs a few seconds to
stabilize the read-out.
o Should the measured resistance exceed the current range or in case of an open
circuit, the display will show “OL”.
7.3 Continuity measurements
Do not perform continuity measurements on live circuits.
Connect the red test lead to the "VΩ " jack and the black lead to the "COM"
jack.
Set the rotary switch to Ω .
Press the SELECT button to select continuity test .
Connect the test probes to the source being measured.
When the measured resistance is less than 30Ω a continuous beep is produced
and the resistance value is showed on the display. Should the measured
resistance exceed the current range or in case of an open circuit, the display will
show “OL”.
Note: Never perform continuity measurements on a live circuit and make sure all
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velleman DVM4200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velleman DVM4200 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info