622286
6
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
DVM1200 VELLEMAN
- 6 -
Relative Measurement Mode
The meter will display the relative measurement in all functions except for the frequency measurement.
1. Select a function and touch the test leads to the circuit to be measured.
2. Press REL to store the measured value and activate the relative measurement mode. The difference
between the reference value and the subsequent reading is displayed.
3. Press REL for more than 2 seconds to return the meter to normal operation.
b. Measurement Functions
AC and DC Voltage Measurement
The meter’s voltage ranges are 600.0mV, 6.000V, 60.00V, 600.0V and 1,000V. AC 600.0mV range only exists in
manual ranging mode.
To measure AC or DC voltages:
1. Set the rotary switch to the proper range.
2. Connect the black and red test leads to the COM and V terminals respectively.
3. Connect the test leads to the circuit being measured.
4. Read the displayed value. The polarity of the red test lead connection will be indicated when making a DC
measurement.
NOTE: The displayed values may be unstable especially at 600mV range, even though you do not put the test
leads into the input terminals. If an erroneous reading is suspected, short the V and the COM terminal and
make sure the LCD displays a zero value. For better accuracy, measure the AC voltage first. Note the AC
voltage range and manually select a DC voltage range equal to or higher than the AC range. This
improves the DC measurement by ensuring that the input protection circuits are not activated.
Resistance Measurement
The meter’s resistance ranges are 600.0Ω, 6.000kΩ, 60.00kΩ, 600.0kΩ, 6.000MΩ and 60.00MΩ.
To measure resistance:
1. Set the rotary switch to the proper range.
2. Connect the black and red test leads to the COM and Ω terminals respectively.
3. Connect the test leads to the circuit being measured and read the displayed value.
NOTE: The measured value of a resistor in a circuit is often different from the resistor’s rated value. This is
because the meter’s test current flows through all possible paths between the probe tips. In order to
ensure the best accuracy in measurement of low resistance, short the test leads before measurement and
remember the test probe resistance. This is necessary to subtract the resistance of the test leads.
The resistance function can produce enough voltage to the forward bias silicon diode or transistor
junctions, causing them to conduct. To avoid this, do not use the 60MΩ range for in-circuit resistance
measurements. On the 60MΩ range, the meter may need a few seconds to stabilize the reading. This is
normal for high resistance measuring. When the input is not connected, i.e. at open circuit, OL will be
displayed for the overrange condition.
To avoid electrical shock and/or damage to the instrument, do not attempt to measure
voltages exceeding 1,000VDC / 1,000VAC RMS.
To avoid electrical shock and/or damage to the instrument, do not apply more 1,000VDC or
1,000VAC RMS between the COM terminal and the earth ground.
To avoid electrical shock and/or damage to the instrument, disconnect the circuit power and
discharge all high-voltage capacitors before measuring resistance.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velleman DVM1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velleman DVM1200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools als bijlage per email.

De handleiding is 1,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info