756782
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
POWX07583 EN
Copyright © 2021 VARO P a g e | 9 www.varo.com
10.2.1 Replacing the saw blade (Fig. 1)
Set the saw to crosscut and mitre saw mode.
Place the blade spanner on the outer flange and undo the saw blade screw (a) by turning
it in a clockwise direction using the Hex key S6. Remove the saw blade screw (a) and the
outer flange.
Remove the saw blade (18) from the inner flange carefully. Lift the lower blade guard (14)
upwards by pressing switch A,
Thoroughly clean the motor shaft and flange before you fit and secure the new saw blade.
Fit and fasten the new saw blade in reverse order.
WARNING: The work to change and align the saw blade must be carried out
correctly.
10.2.2 Mounting upper blade guard (Fig. 2)
Loose the two screws slightly by turning them in a counter-clockwise direction using the
Hex key S5.
Hold the upper blade guard (3) with one hand and the other hand hold the left lower metal
board (b).
Align the two sector gap on the metal board with two screws near the work-light, then
insert the metal board along the table liner slot.
Control the space between the knife Head and the metal board between 3~8 mm.
Tighten the two Screws by turning them in a clockwise direction using the Hex key S5
(26).
CAUTION: Controlling the space between the knife head and the metal
board can prevent the saw blade from cutting to the upper blade guard (3),
thus preventing accidents when operating the machine.
11 FUNCTIONS
11.1 Converting the saw from table to mitre saw for Cross-cut and mitre saw mode
(Fig.3)
Tighten the turntable locking knob (9) and beveling lock (16) by turning them clockwise.
Pull the motor locking pin (38), push down the upper table (1). Pull the saw mode locking
pin (22), then lift the saw table so that it moves into the highest position.
The saw has now been set to Cross-cut and mitre saw mode.
Switch A (8) and the trigger switch (20) are used for starting/stopping the mitre saw.
11.2 Converting the saw from mitre to table saw operating mode (Fig. 4)
Move the turntable to the 90° position, bevel angle at 90° position.
Tighten the turntable locking knob (9) and the beveling lock (16).
Hold the cutting handle (6) and press switch A (8)
Push down the cutting handle to the end and plug in the saw mode locking pin (22) at the
same time
Pull the motor locking pin (38), at the same time pull down the upper sawing table (1) to
the lowest position and release the locking pin (38) once the upper table is in the lowest
position.
The saw has now been set to table saw mode.
The ON/OFF switch (7) is used for starting/stopping the table saw.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Varo POWX07583 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Varo POWX07583 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Varo POWX07583

Varo POWX07583 Gebruiksaanwijzing - Nederlands - 17 pagina's

Varo POWX07583 Gebruiksaanwijzing - Deutsch - 17 pagina's

Varo POWX07583 Gebruiksaanwijzing - Français - 17 pagina's

Varo POWX07583 Aanvulling / aanpassing - Alle talen - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info