611085
9
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
9
7.4 Remove the vent connection unit.
Detach the vent connection unit from the top of the
appliance case by removing the screw at front. Slide
the vent connection unit back and lift clear (see
fig.10).
7.5 Fit the canopy shield.
Attach the canopy shield to the convection air outlet
aperture using the three thread cutting screws
supplied in the fire front pack (see figure 11).
Take care not to damage the vent safety shut-
off switch mounted at the top left of the
convection air outlet
7.6 “Visage” front only
Fit the two surround securing brackets to the
convection box side flanges with the screws
supplied. Be aware of the different orientation of
the brackets at left and right sides - See figure 11A.
8. GAS SUPPLY LINE
INSTALLATION
8.1 Gas connection to the appliance is 3/8”NPT.
8.2 Use only new black iron or steel pipes or copper
tubing if acceptable - check local codes. Note that in
USA copper tubing must be internally tinned for protection
against sulfur compounds.
8.3 Unions in gas lines should be of ground joint type.
8.4 The gas supply line must be sized and installed to
provide a supply of gas sufficient to meet the
maximum demand of the appliance without undue
loss of pressure.
8.5 Sealants used must be resistant to the action of all
gas constituents including LP gas. Sealants should be
applied lightly to male threads to ensure excess
sealant does not enter gas lines.
8.6 The supply line should include a manual shut-off
valve to allow the appliance to be disconnected for
servicing.
8.7 A plugged 1/8”NPT tapping must be installed in the
line. The tapping must be accessible for test gauge
connection and be immediately upstream of the gas
supply connection to the appliance.
8.8 Before the appliance is fitted into the fireplace
opening the supply line must be extended so that it
will project through the opening at back of the
convection box.
The supply pipe route to the gas valve / connector is
shown in figure 12.
Fig12 Supply pipe routing
Fig10 Vent connector removal
Fig. 11 Canopy shield attachment
Left side Right side
Fig. 11A “Visage” surround securing brackets
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Valor 722AN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Valor 722AN in de taal/talen: Engels als bijlage per email.

De handleiding is 0,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info